Powering up the projector, Projection | Panasonic PT-DW100U instruction

Projection (continued)

6 3

1 27

5 4, 8-l 3	9
6

5

4, k8 j

9

Powering up the projector

1 Connect the supplied power cable. (120 V/240 V, 50 Hz/60 Hz)

2 Press the “ ” marked side of the MAIN POWER switch to turn on the power.

•The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode.

3 Press POWER ON “ ”.

•The power indicator lamp illuminates in green and soon the image is projected on the screen.

Note

•If the projector is powered up at about 0 °C, a warm-up period of approximately 5 minutes may be necessary to start projection. The temperature monitor (TEMP) lamp lights up during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen.

•If the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 °C or higher, and then turn on the MAIN POWER switch and the POWER ON “ ” switch once more.

Be sure to set the date and time when the projector is turned on for the first time after being purchased. For details, refer to “Setting the date and time” on page 81.

Making adjustment and

selection

4 Roughly adjust the focus of the lens. (p. 38)

5 Select and set the projection scheme. (p. 76)

6 Select the input signal by pressing the input selector button RGB1, RGB2, DVI-D, VIDEO, S-VIDEO and AUX. (p. 46)

•The AUX button is disabled when an optional input module is not connected.

7 Adjust the tilt of the main unit in front and rear or right and left. (p. 20)

8 Adjust the H & V Lens shift as required. (p. 38)

9 Press AUTO SETUP if the input signal is RGB signal. (p. 47)

j Zoom the lens so the image fills the screen. (p. 38)

k Adjust the focus. (p. 38)

l Readjust the zoom so that the image size fits in the screen. (p. 38)

36 – ENGLISH

Image 36

Panasonic PT-DW100U Powering up the projector, Making adjustment Selection, Projection, Press Power on

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Getting Started PanasonicPage „ Do not disassemble the lamp unit „ Do not place liquid containers on top of the projector„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other Precautions with regard to safety English Before Using Accessories„ Do not place the projector on a vinyl sheet or carpet Level, set the Altitude MODE, described on page 76, to on „ Maintenance Disposal„ To view clear images „ Lamp Remote control unit Location and function of each part„ Front Remote control transmitter window „ Side„ Bottom Lock button Remote control receiver window front Projector Main UnitLocation and function of each part „ Rear „ Controls Connection Terminals p ControlsSelf-diagnosis display ･･･････････ pp Light ON/OFF button „ Connection terminals Using the remote control unit Effective range of remote Control operationLoading batteries Setting projector ID Number to remote control Using a wired remote ControlUsing the remote control unit Installation Examples of system expansion Adjusting the feet Installation geometryInstallation Projection scheme Started GettingSide View Top View For the screen aspect ratio of 169 Units m feet/inches „ Calculation formulas for projection distance by lens types Installation dimensions diagram One unit is used Two units are used Allowable Pin No Signal ConnectionBefore starting connection Pin No Example of connecting with Video devices Connection Example of connecting with personal computers Installing the input module Module Module model Terminal Signal formats supported„ Types of the input modules optional „ Procedure of installation Install the two screws Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module Installation of optional input modules Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional Connecting signals to the DVI-D input module Signal PinDVI-D input module optional How to install Projection lens How to remove Projection lens Power indicator lamp Connecting the power CordIndicator Projector status Status Projection Powering up the projector Making adjustment SelectionPress Power on Projection Powering off the projector Press Power Standby How to adjust the lens How to adjust the focus, zoom and shiftPress to select an item and adjust it „ Using the remote control Adjustment range after lens position optical shift Moving the projection lens position to the home positionModel number of projection lens Lens adjustment to compensate for uneven screen focus How to adjust the lens„ About the focus balance Left Precautions for projector installation work Registration of input signal data Registration of new dataDisplayed Press Enter Clearing Registered Signals data Registration of input signal dataPress Default Sub memory „ How to erase sub memory „ On-screen indicationsRestrictions Using the Shutter Function Switching the input signalOn-screen display Function Status function Automatic adjustment Using the FUNC1 buttonTurning on button Illumination Displaying the internal Test pattern Basic operations using the remote control Press Aspect on the remote controlChanging the picture Aspect ratio On-screen menus „ Picture ppIcon Main Menu item On-screen menus Using the menu screens Resetting to the factory Default Adjusting the picture Switching the picture modeAdjusting Contrast Adjusting Brightness Adjusting ColorAdjusting Tint Adjusting the color Temperature Gamma setting Adjusting the picturePress to switch Color Temperature Press to switch Gamma Sharpness setting Noise reduction settingDynamic iris setting Settings as presettings To display pictures complying With the sRGB standard Display the Picture screen. p Press to select PicturePress to select Natural Press to select Color ET-MD100SD4 Adjusting the position Shift adjustment„ For vertical up and down adjustment Press to select Shift Adjusting the aspect ratio Press to switch AspectPress to select Aspect Adjusting the zoom ratio Clock phase adjustmentAdjusting the position Keystone distortion Correction Press to adjust the correction amount How to use Advanced Menu Blanking adjustmentPress to switch Digital Cinema Reality Digital cinema reality Adjusting the input Resolution Adjusting the clamp Position Edge blending adjustment How to use Advanced Menu Frame delay Press to select Frame DelayPress to switch Frame Delay Press to select Bright Inside Press Enter Press to adjust the position When 43 pictures are displayedRaster position Press to select Raster Position Setting the Display Language Changing the display LanguagePress to select the desired language Display Language Display Option settings Adjusting color matchingPress to switch Color Matching Press to select Color Matching Adjusting the color matching Using a colorimeter These values will not need to beChanged Press to select the colors Press to select their Values After all the data has been input Press Menu Display Option settings RGB in Only RGB inputLarge Screen Correction Press to switch DVI Edid Press to switch DVIPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed On-Screen display setting FeaturesBack Color Press to select Back Color Setting the startup logo Press to switch Back ColorPress to switch Startup Logo Press to select Startup Logo Projector setup Setting a projector IDProjector Setup Press to select Projector ID Installation Setting Altitude ModeProjector setup Direction Press to switch Lamp Select Lamp selectPress to select Lamp Select RS-232C setting Remote2 modeLamp relay Cleaning the air filter Press to select AIR Filter CleaningStatus Press to select Status Auto power off Press to switch TimePress to select Auto Power OFF Press to switch Auto Power OFF Setting FUNC1 Setting the date and timeSave all user data Service password Load all user dataInitialize Press to select Load ALL User Data Using the P in P function Setting the P in P functionPress to select P in P Mode USER1, USER2, USER3 Main Window SUB WindowFrame Lock Type Displaying the internal test pattern „ Cycle of displayed internal test PatternsPress to select Test Pattern Setting the security Setting the security PasswordDisplaying the security Screen Changing the security Password Setting the textChanging the text Control device setup Setting the securityPress to select Control Device Setup Press to select Control Panel or Remote Controller How to use network functions Initial setting of network FunctionNetwork standby Press Enter How to use network functions Network controlNetwork status Press to select Network Network connections „ Name and function of network function partsLAN LINK/ACT lamp green LAN10/100 lamp yellow Accessing from the Web browser „ Change PasswordPress OK to display the Projector status Detailed set up button „ Basic controlSelection tabs Monitor information button Lens adjustment Test pattern display „ Detail control„ Projector status Menu display „ Error information OK Normal operationFailed Occurrence of trouble Parameter Description „ E-mail setup English English „ Authentication set up „ Ping test Temperature Warning Setup Minimum Time „ Adjust clock „ Network config „ Firmware update Using the PJLink protocol Supported commands„ PJLink security authorization Command Control details Using the serial terminals „ Pin assignments and signal names„ Communication conditions Factory setting Examples of connection Pin Signal Description No. name Signal level RS-422-compliant„ For RS-422 Control commands Using the serial terminalsCommand Function of command Remarks Basic format Cable specifications „ Connecting to a PC„ When multiple projectors are connected Using the Remote 2 terminal Example of a control panel layoutPin assignments and control Names of terminals Open H Short L Monitor Lamp Indicators Lamp Cleaning and replacement of air filter Procedure of cleaningProjector Install the movable metal mesh Filter to the filter cleaning unitInstall the brush cover so that it Replacement of lamp unit Precautions on lamp unit replacementTiming of lamp unit replacement „ Indication after 1 800 hours Procedure of lamp unit replacement Use a Phillips screwdriver toLamp unit to be replaced until Lamp unit cover screw Installation procedure Symptoms Check point Power does not turn on Self-diagnosis display Details Remedy FF0 Specifications Model NoPT-DW100U RGB2 input Compatible Signals Appendix MAC21 List of P in P Appendix Dimensions Outside dimensions Index Wired remote control ･･････････････････････････ Trademark Acknowledgement Français Précautions de sécurité „ Ne pas surcharger la prise du secteur„ Ne pas retirer le capot ou le modifier „ Ne pas placer le projecteur sur des surfaces instables „ Ne jamais démonter la lampe„ Ne pas mettre d’objets étrangers dans le projecteur „ Ne pas placer plusieurs kits les uns sur les autres Mise en garde Précautions de sécurité suiteNe pas placer d’objets lourds sur le projecteur Ne pas mélanger des piles anciennes et nouvelles „ Ne jamais réutiliser une lampe usagée Accessoires Mise en garde concernant les déplacements du projecteurMises en garde concernant la configuration Avant l’utilisation Remarques concernant l’utilisation Mise au rebutRemarques concernant la sécurité Remplacement de la lampe Précautions à prendre lors du remplacement de la lampeIntervalle de remplacement de la lampe „ Indication après 1 800 heures Procédure de remplacement de la lampe Vis du couvercle de la lampe Tqbj S0808-2098C