Connection, Before starting connection | Panasonic PT-DW100U

Connection

Before starting connection

•Before connection, read carefully the instruction manual for the device to be connected.

•Turning off the power switch of the devices before connecting cables.

•If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device.

•Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In this case, a time base corrector (TBC) must be connected.

•The projector accepts the following signals: video, S-Video, analog RGB, DVI-D and signals which are compatible with the optional input module (p. 28).

•Some PC models cannot be connected to the projector.

zThe pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below.

	Pin No.	Signal
	1	Ground (luminance signal)
	2	Ground (color signal)
Outside view	3	Luminance signal
Outside view	4	Color signal

zThe pin-out and signal names of the RGB2 IN terminal are shown in the diagram below.

Pin No.

Signal

1R/PR

2	G/G • SYNC/Y
3	B/PB

mHD/SYNC

nVD

Outside view

4, 9, l,and o are not assigned. 5-8, j and k are GND terminals.

zThe pin-out and signal names of the DVI-D IN terminal are shown in the diagram below.

Getting Started

x q

p 9

81

Outside view

	Pin No.	Signal	Pin No.	Signal

	1	T.M.D.S data 2–	m
	2	T.M.D.S data 2+	n	+5V
	3	T.M.D.S data 2 / 4 shield	o	Ground
	3	T.M.D.S data 2 / 4 shield	p	Hot plug detection
			p	Hot plug detection
	4		q	T.M.D.S data 0-
	5		r	T.M.D.S data 0+
	6	DDC clock	s	T.M.D.S data 0 / 5 shield
	7	DDC data	s	T.M.D.S data 0 / 5 shield
	7	DDC data
	8		t

	9	T.M.D.S data 1–	u
	j	T.M.D.S data 1+	v	T.M.D.S clock shield
	k	T.M.D.S data 1 / 3 shield	w	T.M.D.S clock+
	l		x	T.M.D.S clock–

ENGLISH – 25

Image 25

Panasonic PT-DW100U operating instructions Connection, Before starting connection, Outside view, Pin No Signal

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Panasonic Getting StartedPage „ Do not place liquid containers on top of the projector „ Do not disassemble the lamp unit„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other Precautions with regard to safety English Accessories Before Using„ Do not place the projector on a vinyl sheet or carpet Level, set the Altitude MODE, described on page 76, to on Disposal „ Maintenance„ To view clear images „ Lamp Location and function of each part Remote control unit„ Front „ Side Remote control transmitter window„ Bottom Lock button Projector Main Unit Remote control receiver window frontLocation and function of each part „ Rear Connection Terminals p Controls „ ControlsSelf-diagnosis display ･･･････････ pp Light ON/OFF button „ Connection terminals Effective range of remote Control operation Using the remote control unitLoading batteries Using a wired remote Control Setting projector ID Number to remote controlUsing the remote control unit Examples of system expansion Installation Installation geometry Adjusting the feetInstallation Projection scheme Getting StartedSide View Top View For the screen aspect ratio of 169 Units m feet/inches „ Calculation formulas for projection distance by lens types One unit is used Two units are used Allowable Installation dimensions diagram Connection Pin No SignalBefore starting connection Pin No Connection Example of connecting with Video devices Example of connecting with personal computers Module Module model Terminal Signal formats supported Installing the input module„ Types of the input modules optional Install the two screws Register the input signal „ Procedure of installationRemove the slot cover Insert the input module Installation of optional input modules Connecting signals to the input module Connecting the signal to the HD/SD-SDI input module Connecting the signal to the SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional Signal Pin Connecting signals to the DVI-D input moduleDVI-D input module optional How to remove Projection lens How to install Projection lens Connecting the power Cord Power indicator lampIndicator Projector status Status Projection Making adjustment Selection Powering up the projectorPress Power on Projection Press Power Standby Powering off the projector How to adjust the focus, zoom and shift How to adjust the lensPress to select an item and adjust it „ Using the remote control Moving the projection lens position to the home position Adjustment range after lens position optical shiftModel number of projection lens How to adjust the lens Lens adjustment to compensate for uneven screen focus„ About the focus balance Left Precautions for projector installation work Registration of new data Registration of input signal dataDisplayed Press Enter Registration of input signal data Clearing Registered Signals dataPress Default Sub memory „ On-screen indications „ How to erase sub memoryRestrictions Switching the input signal Using the Shutter FunctionOn-screen display Function Status function Using the FUNC1 button Automatic adjustmentTurning on button Illumination Displaying the internal Test pattern Press Aspect on the remote control Basic operations using the remote controlChanging the picture Aspect ratio „ Picture pp On-screen menusIcon Main Menu item On-screen menus Resetting to the factory Default Using the menu screens Switching the picture mode Adjusting the pictureAdjusting Contrast Adjusting Color Adjusting BrightnessAdjusting Tint Adjusting the color Temperature Adjusting the picture Gamma settingPress to switch Color Temperature Press to switch Gamma Noise reduction setting Sharpness settingDynamic iris setting Settings as presettings Display the Picture screen. p Press to select Picture To display pictures complying With the sRGB standardPress to select Natural Press to select Color ET-MD100SD4 Shift adjustment Adjusting the position„ For vertical up and down adjustment Press to select Shift Press to switch Aspect Adjusting the aspect ratioPress to select Aspect Clock phase adjustment Adjusting the zoom ratioAdjusting the position Keystone distortion Correction Press to adjust the correction amount Blanking adjustment How to use Advanced MenuPress to switch Digital Cinema Reality Digital cinema reality Adjusting the clamp Position Adjusting the input Resolution How to use Advanced Menu Edge blending adjustment Press to select Frame Delay Frame delayPress to switch Frame Delay Press to select Bright Inside Press Enter When 43 pictures are displayed Press to adjust the positionRaster position Press to select Raster Position Changing the display Language Setting the Display LanguagePress to select the desired language Display Language Adjusting color matching Display Option settingsPress to switch Color Matching Press to select Color Matching These values will not need to be Adjusting the color matching Using a colorimeterChanged Press to select the colors Press to select their Values After all the data has been input Press Menu RGB in Only RGB input Display Option settingsLarge Screen Correction Press to switch DVI Press to switch DVI EdidPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed Features On-Screen display settingBack Color Press to select Back Color Press to switch Back Color Setting the startup logoPress to switch Startup Logo Press to select Startup Logo Setting a projector ID Projector setupProjector Setup Press to select Projector ID Altitude Mode Installation SettingProjector setup Direction Lamp select Press to switch Lamp SelectPress to select Lamp Select Remote2 mode RS-232C settingLamp relay Press to select AIR Filter Cleaning Cleaning the air filterStatus Press to select Status Press to switch Time Auto power offPress to select Auto Power OFF Press to switch Auto Power OFF Setting the date and time Setting FUNC1Save all user data Load all user data Service passwordInitialize Press to select Load ALL User Data Setting the P in P function Using the P in P functionPress to select P in P Mode USER1, USER2, USER3 SUB Window Main WindowFrame Lock Type „ Cycle of displayed internal test Patterns Displaying the internal test patternPress to select Test Pattern Setting the security Password Setting the securityDisplaying the security Screen Setting the text Changing the security PasswordChanging the text Setting the security Control device setupPress to select Control Device Setup Press to select Control Panel or Remote Controller Initial setting of network Function How to use network functionsNetwork standby Press Enter Network control How to use network functionsNetwork status Press to select Network „ Name and function of network function parts Network connectionsLAN LINK/ACT lamp green LAN10/100 lamp yellow „ Change Password Accessing from the Web browserPress OK to display the Projector status „ Basic control Detailed set up buttonSelection tabs Monitor information button „ Detail control Lens adjustment Test pattern display„ Projector status Menu display OK Normal operation „ Error informationFailed Occurrence of trouble Parameter Description „ E-mail setup English English „ Ping test „ Authentication set up Temperature Warning Setup Minimum Time „ Network config „ Adjust clock „ Firmware update Supported commands Using the PJLink protocol„ PJLink security authorization Command Control details „ Pin assignments and signal names Using the serial terminals„ Communication conditions Factory setting Examples of connection Signal level RS-422-compliant Pin Signal Description No. name„ For RS-422 Using the serial terminals Control commandsCommand Function of command Remarks Basic format „ Connecting to a PC Cable specifications„ When multiple projectors are connected Example of a control panel layout Using the Remote 2 terminalPin assignments and control Names of terminals Open H Short L Lamp Monitor Lamp Indicators Procedure of cleaning Cleaning and replacement of air filterProjector Filter to the filter cleaning unit Install the movable metal meshInstall the brush cover so that it Precautions on lamp unit replacement Replacement of lamp unitTiming of lamp unit replacement „ Indication after 1 800 hours Use a Phillips screwdriver to Procedure of lamp unit replacementLamp unit to be replaced until Lamp unit cover screw Installation procedure Power does not turn on Symptoms Check point Details Remedy Self-diagnosis display FF0 Model No SpecificationsPT-DW100U RGB2 input Appendix Compatible Signals MAC21 Appendix List of P in P Outside dimensions Dimensions Index Wired remote control ･･････････････････････････ Trademark Acknowledgement Français „ Ne pas surcharger la prise du secteur Précautions de sécurité„ Ne pas retirer le capot ou le modifier „ Ne jamais démonter la lampe „ Ne pas placer le projecteur sur des surfaces instables„ Ne pas mettre d’objets étrangers dans le projecteur „ Ne pas placer plusieurs kits les uns sur les autres Précautions de sécurité suite Mise en gardeNe pas placer d’objets lourds sur le projecteur Ne pas mélanger des piles anciennes et nouvelles „ Ne jamais réutiliser une lampe usagée Mise en garde concernant les déplacements du projecteur AccessoiresMises en garde concernant la configuration Avant l’utilisation Mise au rebut Remarques concernant l’utilisationRemarques concernant la sécurité Précautions à prendre lors du remplacement de la lampe Remplacement de la lampeIntervalle de remplacement de la lampe „ Indication après 1 800 heures Vis du couvercle de la lampe Procédure de remplacement de la lampe Tqbj S0808-2098C