Adjusting the feet, Projection scheme | Panasonic PT-DW100U manual

Installation (continued)

Adjusting the feet

The four adjustable feet (p. 14) mounted at the bottom of the projector are level-adjustable (0 mm–15 mm) which can be used when the mounting surface is uneven.

(Front)

(Rear)

Projection scheme

All four combinations of Front, Rear, Ceiling or Floor mounting are available. Use the INSTALLATION menu to choose the desired projection scheme. (p. 76)

Installation geometry

When planning the projector and screen geometry, refer to the figures below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens shifting mechanism.

zWhen attaching an optional ceiling mount bracket (ET-PKD100H)

Side View	(unit : mm/inch)
	700.5	27.6˝)
H	580.5 -	(22.9˝ -
H
	L
	254
SH	(10˝)
SH
	L
H
Screen

Top View	(unit : mm/inch)
	200
	(7.9˝)
	66	(2.6˝)
SW	L	120	(4.7˝) 314 (12.4˝)
SW		120	(4.7˝) 314 (12.4˝)
	L1
	175
	(6.9˝)
Screen	254
Screen	(10˝)
	(10˝)

LProjection distance

	SH	Height of the image
	SW	Image width
	H	Vertical distance between the lens center level and
	H	the bottom edge of the projected image
		the bottom edge of the projected image

*H = -0.2 × SH to 1.2 × SH

*However, if the ET-D75LE5 has been installed, the value will be fixed at H=SH/2. If the ET-D75LE6 has been installed, the values will be H = -0.1 × SH to 1.1 × SH.

	Lens	Lens Protrusion L1
	Lens	(Approx.)
		(Approx.)

	ET-D75LE1	62.5 (2.5˝)
	ET-D75LE2	47 (1.9˝)
	ET-D75LE3	50.5 (2˝)
	ET-D75LE4	74.4 (2.9˝)
	ET-D75LE5	150.5 (5.9˝)
	ET-D75LE6	160 (6.3˝)
	ET-D75LE8	202.5 (8˝)

20 – ENGLISH

Image 20

Panasonic PT-DW100U Adjusting the feet, Projection scheme, Installation geometry, Lens Lens Protrusion L1 Approx

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Getting Started PanasonicPage „ Do not disassemble the lamp unit „ Do not place liquid containers on top of the projector„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other Precautions with regard to safety English Before Using Accessories„ Do not place the projector on a vinyl sheet or carpet Level, set the Altitude MODE, described on page 76, to on „ Maintenance Disposal„ To view clear images „ Lamp „ Front Remote control unitLocation and function of each part Remote control transmitter window „ Side„ Bottom Lock button Remote control receiver window front Projector Main UnitLocation and function of each part „ Rear Self-diagnosis display ･･･････････ pp Light ON/OFF button „ ControlsConnection Terminals p Controls „ Connection terminals Loading batteries Using the remote control unitEffective range of remote Control operation Using the remote control unit Setting projector ID Number to remote controlUsing a wired remote Control Installation Examples of system expansion Adjusting the feet Installation geometryInstallation Projection scheme Side View Top View StartedGetting For the screen aspect ratio of 169 Units m feet/inches „ Calculation formulas for projection distance by lens types Installation dimensions diagram One unit is used Two units are used Allowable Pin No Signal ConnectionBefore starting connection Pin No Example of connecting with Video devices Connection Example of connecting with personal computers „ Types of the input modules optional Installing the input moduleModule Module model Terminal Signal formats supported „ Procedure of installation Install the two screws Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module Installation of optional input modules Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional DVI-D input module optional Connecting signals to the DVI-D input moduleSignal Pin How to install Projection lens How to remove Projection lens Power indicator lamp Connecting the power CordIndicator Projector status Status Projection Powering up the projector Making adjustment SelectionPress Power on Projection Powering off the projector Press Power Standby How to adjust the lens How to adjust the focus, zoom and shiftPress to select an item and adjust it „ Using the remote control Model number of projection lens Adjustment range after lens position optical shiftMoving the projection lens position to the home position „ About the focus balance Lens adjustment to compensate for uneven screen focusHow to adjust the lens Left Precautions for projector installation work Registration of input signal data Registration of new dataDisplayed Press Enter Clearing Registered Signals data Registration of input signal dataPress Default Sub memory Restrictions „ How to erase sub memory„ On-screen indications Using the Shutter Function Switching the input signalOn-screen display Function Status function Automatic adjustment Using the FUNC1 buttonTurning on button Illumination Displaying the internal Test pattern Changing the picture Aspect ratio Basic operations using the remote controlPress Aspect on the remote control Icon Main Menu item On-screen menus„ Picture pp On-screen menus Using the menu screens Resetting to the factory Default Adjusting Contrast Adjusting the pictureSwitching the picture mode Adjusting Brightness Adjusting ColorAdjusting Tint Adjusting the color Temperature Gamma setting Adjusting the picturePress to switch Color Temperature Press to switch Gamma Dynamic iris setting Sharpness settingNoise reduction setting Settings as presettings To display pictures complying With the sRGB standard Display the Picture screen. p Press to select PicturePress to select Natural Press to select Color ET-MD100SD4 Adjusting the position Shift adjustment„ For vertical up and down adjustment Press to select Shift Press to select Aspect Adjusting the aspect ratioPress to switch Aspect Adjusting the zoom ratio Clock phase adjustmentAdjusting the position Keystone distortion Correction Press to adjust the correction amount How to use Advanced Menu Blanking adjustmentPress to switch Digital Cinema Reality Digital cinema reality Adjusting the input Resolution Adjusting the clamp Position Edge blending adjustment How to use Advanced Menu Frame delay Press to select Frame DelayPress to switch Frame Delay Press to select Bright Inside Press Enter Press to adjust the position When 43 pictures are displayedRaster position Press to select Raster Position Setting the Display Language Changing the display LanguagePress to select the desired language Display Language Display Option settings Adjusting color matchingPress to switch Color Matching Press to select Color Matching Adjusting the color matching Using a colorimeter These values will not need to beChanged Press to select the colors Press to select their Values After all the data has been input Press Menu Large Screen Correction Display Option settingsRGB in Only RGB input Press to switch DVI Edid Press to switch DVIPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed On-Screen display setting FeaturesBack Color Press to select Back Color Setting the startup logo Press to switch Back ColorPress to switch Startup Logo Press to select Startup Logo Projector setup Setting a projector IDProjector Setup Press to select Projector ID Installation Setting Altitude ModeProjector setup Direction Press to select Lamp Select Press to switch Lamp SelectLamp select Lamp relay RS-232C settingRemote2 mode Cleaning the air filter Press to select AIR Filter CleaningStatus Press to select Status Auto power off Press to switch TimePress to select Auto Power OFF Press to switch Auto Power OFF Save all user data Setting FUNC1Setting the date and time Service password Load all user dataInitialize Press to select Load ALL User Data Using the P in P function Setting the P in P functionPress to select P in P Mode USER1, USER2, USER3 Main Window SUB WindowFrame Lock Type Displaying the internal test pattern „ Cycle of displayed internal test PatternsPress to select Test Pattern Displaying the security Screen Setting the securitySetting the security Password Changing the text Changing the security PasswordSetting the text Control device setup Setting the securityPress to select Control Device Setup Press to select Control Panel or Remote Controller How to use network functions Initial setting of network FunctionNetwork standby Press Enter How to use network functions Network controlNetwork status Press to select Network Network connections „ Name and function of network function partsLAN LINK/ACT lamp green LAN10/100 lamp yellow Press OK to display the Projector status Accessing from the Web browser„ Change Password Detailed set up button „ Basic controlSelection tabs Monitor information button Lens adjustment Test pattern display „ Detail control„ Projector status Menu display „ Error information OK Normal operationFailed Occurrence of trouble Parameter Description „ E-mail setup English English „ Authentication set up „ Ping test Temperature Warning Setup Minimum Time „ Adjust clock „ Network config „ Firmware update Using the PJLink protocol Supported commands„ PJLink security authorization Command Control details Using the serial terminals „ Pin assignments and signal names„ Communication conditions Factory setting Examples of connection „ For RS-422 Pin Signal Description No. nameSignal level RS-422-compliant Control commands Using the serial terminalsCommand Function of command Remarks Basic format „ When multiple projectors are connected Cable specifications„ Connecting to a PC Using the Remote 2 terminal Example of a control panel layoutPin assignments and control Names of terminals Open H Short L Monitor Lamp Indicators Lamp Projector Cleaning and replacement of air filterProcedure of cleaning Install the brush cover so that it Install the movable metal meshFilter to the filter cleaning unit Replacement of lamp unit Precautions on lamp unit replacementTiming of lamp unit replacement „ Indication after 1 800 hours Procedure of lamp unit replacement Use a Phillips screwdriver toLamp unit to be replaced until Lamp unit cover screw Installation procedure Symptoms Check point Power does not turn on Self-diagnosis display Details Remedy FF0 PT-DW100U SpecificationsModel No RGB2 input Compatible Signals Appendix MAC21 List of P in P Appendix Dimensions Outside dimensions Index Wired remote control ･･････････････････････････ Trademark Acknowledgement Français „ Ne pas retirer le capot ou le modifier Précautions de sécurité„ Ne pas surcharger la prise du secteur „ Ne pas placer le projecteur sur des surfaces instables „ Ne jamais démonter la lampe„ Ne pas mettre d’objets étrangers dans le projecteur „ Ne pas placer plusieurs kits les uns sur les autres Mise en garde Précautions de sécurité suiteNe pas placer d’objets lourds sur le projecteur Ne pas mélanger des piles anciennes et nouvelles „ Ne jamais réutiliser une lampe usagée Accessoires Mise en garde concernant les déplacements du projecteurMises en garde concernant la configuration Avant l’utilisation Remarques concernant la sécurité Remarques concernant l’utilisationMise au rebut Remplacement de la lampe Précautions à prendre lors du remplacement de la lampeIntervalle de remplacement de la lampe „ Indication après 1 800 heures Procédure de remplacement de la lampe Vis du couvercle de la lampe Tqbj S0808-2098C