Installation Setting, Altitude Mode | Panasonic PT-DW100U instruction

Projector setup (continued)

Installation Setting

A projection scheme can be chosen depending on the installation of the projector. If the picture is shown upside down or in reverse, change the projection scheme.

•Select the setting by displaying the on-screen indications using buttons of the remote control or the control panel on the main unit.

1. Press ▲▼ to select

“INSTALLATION”.
	PROJECTOR ID	ALL
	INSTALLATION	FRONT-FLOOR
	ALTITUDE MODE	ON

2.Press ◄► to switch “INSTALLATION”.

•The setting will change as follows each time ◄► is pressed.

FRONT-FLOOR FRONT-CELING

3.Press MENU twice.

•The on-screen indications disappear and the normal screen appears again.

Altitude Mode

When using the projector over 1 400 m above sea level, set to “ON”.

1. Press ▲▼ to select “ALTITUDE MODE”.

INSTALLATIONFRONT-FLOOR

ALTITUDE MODE	ON
DIRECTION	HORIZONTAL

2.Press ◄► to switch “ALTITUDE MODE”.

•The setting will change as follows each time ◄► is pressed.

OFF

ON

	REAR-CELING		REAR-FLOOR
	REAR-CELING		REAR-FLOOR

Floor mount front projection (FRONT-FLOOR)

Ceiling mount front projection (FRONT-CEILING)

Floor mount rear projection (REAR-FLOOR)

Ceiling mount rear projection (REAR-CEILING)

Direction

The fan speed is changed in accordance with the projector orientation (pointed forward, or toward the ceiling or floor)

1. Press ▲▼ to select “DIRECTION”.

	ALTITUDE MODE	ON
	DIRECTION	HORIZONTAL
	LAMP SELECT	QUAD

2.Press ◄► to switch “DIRECTION”.

•The setting will change as follows each time ◄► is pressed.

HORIZONTAL

VERTICAL

•HORIZONTAL:

This is the standard setup.

•VERTICAL:

Select this if the projector is tilted at a large vertical angle (an angle which exceeds 30°from the horizontal).

76 – ENGLISH

Image 76

Panasonic PT-DW100U operating instructions Installation Setting, Altitude Mode, Direction, Projector setup

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Getting Started PanasonicPage „ Do not disassemble the lamp unit „ Do not place liquid containers on top of the projector„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other Precautions with regard to safety English Before Using Accessories„ Do not place the projector on a vinyl sheet or carpet Level, set the Altitude MODE, described on page 76, to on „ Maintenance Disposal„ To view clear images „ Lamp Location and function of each part Remote control unit„ Front Remote control transmitter window „ Side„ Bottom Lock button Remote control receiver window front Projector Main UnitLocation and function of each part „ Rear Connection Terminals p Controls „ ControlsSelf-diagnosis display ･･･････････ pp Light ON/OFF button „ Connection terminals Effective range of remote Control operation Using the remote control unitLoading batteries Using a wired remote Control Setting projector ID Number to remote controlUsing the remote control unit Installation Examples of system expansion Adjusting the feet Installation geometryInstallation Projection scheme Getting StartedSide View Top View For the screen aspect ratio of 169 Units m feet/inches „ Calculation formulas for projection distance by lens types Installation dimensions diagram One unit is used Two units are used Allowable Pin No Signal ConnectionBefore starting connection Pin No Example of connecting with Video devices Connection Example of connecting with personal computers Module Module model Terminal Signal formats supported Installing the input module„ Types of the input modules optional „ Procedure of installation Install the two screws Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module Installation of optional input modules Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional Signal Pin Connecting signals to the DVI-D input moduleDVI-D input module optional How to install Projection lens How to remove Projection lens Power indicator lamp Connecting the power CordIndicator Projector status Status Projection Powering up the projector Making adjustment SelectionPress Power on Projection Powering off the projector Press Power Standby How to adjust the lens How to adjust the focus, zoom and shiftPress to select an item and adjust it „ Using the remote control Moving the projection lens position to the home position Adjustment range after lens position optical shiftModel number of projection lens How to adjust the lens Lens adjustment to compensate for uneven screen focus„ About the focus balance Left Precautions for projector installation work Registration of input signal data Registration of new dataDisplayed Press Enter Clearing Registered Signals data Registration of input signal dataPress Default Sub memory „ On-screen indications „ How to erase sub memoryRestrictions Using the Shutter Function Switching the input signalOn-screen display Function Status function Automatic adjustment Using the FUNC1 buttonTurning on button Illumination Displaying the internal Test pattern Press Aspect on the remote control Basic operations using the remote controlChanging the picture Aspect ratio „ Picture pp On-screen menusIcon Main Menu item On-screen menus Using the menu screens Resetting to the factory Default Switching the picture mode Adjusting the pictureAdjusting Contrast Adjusting Brightness Adjusting ColorAdjusting Tint Adjusting the color Temperature Gamma setting Adjusting the picturePress to switch Color Temperature Press to switch Gamma Noise reduction setting Sharpness settingDynamic iris setting Settings as presettings To display pictures complying With the sRGB standard Display the Picture screen. p Press to select PicturePress to select Natural Press to select Color ET-MD100SD4 Adjusting the position Shift adjustment„ For vertical up and down adjustment Press to select Shift Press to switch Aspect Adjusting the aspect ratioPress to select Aspect Adjusting the zoom ratio Clock phase adjustmentAdjusting the position Keystone distortion Correction Press to adjust the correction amount How to use Advanced Menu Blanking adjustmentPress to switch Digital Cinema Reality Digital cinema reality Adjusting the input Resolution Adjusting the clamp Position Edge blending adjustment How to use Advanced Menu Frame delay Press to select Frame DelayPress to switch Frame Delay Press to select Bright Inside Press Enter Press to adjust the position When 43 pictures are displayedRaster position Press to select Raster Position Setting the Display Language Changing the display LanguagePress to select the desired language Display Language Display Option settings Adjusting color matchingPress to switch Color Matching Press to select Color Matching Adjusting the color matching Using a colorimeter These values will not need to beChanged Press to select the colors Press to select their Values After all the data has been input Press Menu RGB in Only RGB input Display Option settingsLarge Screen Correction Press to switch DVI Edid Press to switch DVIPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed On-Screen display setting FeaturesBack Color Press to select Back Color Setting the startup logo Press to switch Back ColorPress to switch Startup Logo Press to select Startup Logo Projector setup Setting a projector IDProjector Setup Press to select Projector ID Installation Setting Altitude ModeProjector setup Direction Lamp select Press to switch Lamp SelectPress to select Lamp Select Remote2 mode RS-232C settingLamp relay Cleaning the air filter Press to select AIR Filter CleaningStatus Press to select Status Auto power off Press to switch TimePress to select Auto Power OFF Press to switch Auto Power OFF Setting the date and time Setting FUNC1Save all user data Service password Load all user dataInitialize Press to select Load ALL User Data Using the P in P function Setting the P in P functionPress to select P in P Mode USER1, USER2, USER3 Main Window SUB WindowFrame Lock Type Displaying the internal test pattern „ Cycle of displayed internal test PatternsPress to select Test Pattern Setting the security Password Setting the securityDisplaying the security Screen Setting the text Changing the security PasswordChanging the text Control device setup Setting the securityPress to select Control Device Setup Press to select Control Panel or Remote Controller How to use network functions Initial setting of network FunctionNetwork standby Press Enter How to use network functions Network controlNetwork status Press to select Network Network connections „ Name and function of network function partsLAN LINK/ACT lamp green LAN10/100 lamp yellow „ Change Password Accessing from the Web browserPress OK to display the Projector status Detailed set up button „ Basic controlSelection tabs Monitor information button Lens adjustment Test pattern display „ Detail control„ Projector status Menu display „ Error information OK Normal operationFailed Occurrence of trouble Parameter Description „ E-mail setup English English „ Authentication set up „ Ping test Temperature Warning Setup Minimum Time „ Adjust clock „ Network config „ Firmware update Using the PJLink protocol Supported commands„ PJLink security authorization Command Control details Using the serial terminals „ Pin assignments and signal names„ Communication conditions Factory setting Examples of connection Signal level RS-422-compliant Pin Signal Description No. name„ For RS-422 Control commands Using the serial terminalsCommand Function of command Remarks Basic format „ Connecting to a PC Cable specifications„ When multiple projectors are connected Using the Remote 2 terminal Example of a control panel layoutPin assignments and control Names of terminals Open H Short L Monitor Lamp Indicators Lamp Procedure of cleaning Cleaning and replacement of air filterProjector Filter to the filter cleaning unit Install the movable metal meshInstall the brush cover so that it Replacement of lamp unit Precautions on lamp unit replacementTiming of lamp unit replacement „ Indication after 1 800 hours Procedure of lamp unit replacement Use a Phillips screwdriver toLamp unit to be replaced until Lamp unit cover screw Installation procedure Symptoms Check point Power does not turn on Self-diagnosis display Details Remedy FF0 Model No SpecificationsPT-DW100U RGB2 input Compatible Signals Appendix MAC21 List of P in P Appendix Dimensions Outside dimensions Index Wired remote control ･･････････････････････････ Trademark Acknowledgement Français „ Ne pas surcharger la prise du secteur Précautions de sécurité„ Ne pas retirer le capot ou le modifier „ Ne pas placer le projecteur sur des surfaces instables „ Ne jamais démonter la lampe„ Ne pas mettre d’objets étrangers dans le projecteur „ Ne pas placer plusieurs kits les uns sur les autres Mise en garde Précautions de sécurité suiteNe pas placer d’objets lourds sur le projecteur Ne pas mélanger des piles anciennes et nouvelles „ Ne jamais réutiliser une lampe usagée Accessoires Mise en garde concernant les déplacements du projecteurMises en garde concernant la configuration Avant l’utilisation Mise au rebut Remarques concernant l’utilisationRemarques concernant la sécurité Remplacement de la lampe Précautions à prendre lors du remplacement de la lampeIntervalle de remplacement de la lampe „ Indication après 1 800 heures Procédure de remplacement de la lampe Vis du couvercle de la lampe Tqbj S0808-2098C