Traps enterprise-Specific, DevHealthAndStatus | Paradyne 9123

SNMP MIBs and Traps, and RMON Alarm Defaults

Traps: enterprise-Specific

These traps indicate that an enterprise-specific event has occurred. Supported enterprise-specific traps are listed below.

Table B-7. enterprise-Specific Traps and Variable-Bindings (1 of 3)

Trap

Variable-Bindings

Possible Cause

enterpriseCIR- Change(15)

HdevFrExtDlciIfIndex (devFrExt.mib)

HdevFrExtDlciDlci (devFrExt.mib)

HdevFrExtDlciCIR (devFrExt.mib)

HdevLastTrapString (devHealthAndStatus.- mib)

CIR has changed due to the LMI report. LMI Protocol is set to Standard and the network's CIR changed.

String:

`CIR on $ifString changed to $CIR bps.'

enterpriseConfig-	H devLastTrapString	Configuration has been changed
Change(6)	(devHealthAndStatus.-	via the menu-driven user
	mib)	interface, an SNMP Manager,
		or auto-configuration after 60
		seconds has elapsed without
		another change.
		String:
		`Device configuration change.'

enterpriseDLCI-	H devFrExtDlciIfIndex	The DLCI has been deleted. The
delete(17)	(devFrExt.mib)	network no longer supports the
	H devFrExtDlciDlci	DLCI, and it was removed.
	H devFrExtDlciDlci
	(devFrExt.mib)	Strings:
	H devLastTrapString	`$ifString deleted by Auto-DLCI
	H devLastTrapString	delete.'
	(devHealthAndStatus.-	delete.'
	(devHealthAndStatus.-
enterpriseDLCI-	mib.)	DLCI Status is set to Inactive; the
enterpriseDLCI-		DLCI Status is set to Inactive; the
Down(11)		DLCI is down.
		Strings:
		`$ifString down.' (Due to LMI or
		physical failure.)
		`$ifString administratively
		shutdown.' (Due to an intentional
		shutdown.)

enterpriseDLCIUp(12)		DLCI Status is set to Active;
		DLCI is up again.
		String:
		`$ifString up.'

9123-A2-GB20-10

July 2000

B-11

Image 237

Paradyne 9123 manual Traps enterprise-Specific, DevHealthAndStatus

Contents

FrameSaver Flex Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuration Security and Logins Troubleshooting Setting Up NetScout Manager Plus for FrameSaver Devices Index About This Guide Purpose and Intended AudienceDocument Organization Where installation and setup information is located and how Setting Up OpenLane for FrameSaver Devices. IdentifiesSetting Up NetScout Manager Plus for FrameSaver Devices. Describes setup of the NetScout Manager Plus Product-Related Documents Conventions Used When viewing this manual online. Click onTo indicate a hyperlink to additional information Highlighted text About the FrameSaver Flex System OverviewSystem Overview FrameSaver Flex Feature Sets Flex Flex SLV Feature Feature Set Basic Advanced Basic Flex Features Maximum Number of PVCs and Management PVCs Supported 9123-A1-211 9123-A1-213 Feature 9123-A1-221 9123-A1-223Models Through Connections PVCs Dedicated Management PVCs July Advanced Flex SLV Features OpenLane SLM System NetScout Manager Plus and NetScout Probes About the FrameSaver Flex User Interface Basic Operation Logging On Procedure If your login was Then Main Menu SelectMain Menu Service Level Verification System Options Screen Work AreasScreen Format Description Navigating the Screens Keyboard KeysPress Select For the screen Press Enter to Function Function Keys Selecting from a Menu Switching Between Screen Areas Selecting a Field Entering InformationExample User Interface and Basic Operation Configuration Configuration Basic Configuration Configuration MenuConfiguration EDIT/DISPLAY Configuration Option Area Description Configuration Option Areas Main Menu → Configuration Accessing and Displaying Configuration Options Configuration → PVC Connections Changing Configuration Options Saving Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example Default If the selection is Unit is configured to operate Entering System Information Setting the System Clock Setting Up So the Router Can Receive RIPConfiguration → Data Ports → Dlci Records Main Menu → Control → System Information Main Menu → Auto-Configuration Setting Up Auto-ConfigurationAuto-Configuration Screen Example AUTO-CONFIGURATION Selecting a Frame Relay Discovery Mode Main Menu → Auto-Configuration → Frame Relay Discovery ModeDiscovery Mode Configuration Description 9123-A2-GB20-10 July Automatically Removing a Circuit Setting Up Back-to-Back Operation Changing Operating ModeMain Menu → Control → Change Operating Mode Configuring the Overall System Configuration Option Tables Main Menu → Configuration → System → Frame Relay and LMI Configuring Frame Relay and LMI for the SystemSystem Frame Relay and LMI Options 1 LMI Behavior LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 System Frame Relay and LMI Options 2Traffic Policing System Frame Relay and LMI Options 3 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 Service Level Verification Options 1 Configuring Service Level Verification Options Service Level Verification Options 2 SLV Timeout Clearing Event ThresholdSLV Packet Size bytes Configuring General System Options Main Menu → Configuration → System→ GeneralGeneral System Options Configuring the Network Interface Configuring the Physical InterfacesMain Menu → Configuration → Network → Physical Network Physical Interface Options 1 Bit Stuffing Network Physical Interface Options 2Transmit Timing Network Initiated LLB Network Physical Interface Options 3 Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Initiated PLB Ansi Performance Report Messages Circuit Identifier Network Physical Interface Options 4 Main Menu → Configuration → Data Ports → Physical Configuring the User Data PortData Port Physical Interface Options 1 Transmit Clock Source Data Port Physical Interface Options 2 Monitor RTS ControlPort DTE Initiated Loopbacks Main Menu → Easy Install → Time Slot Assignment Screen Assigning Time Slots/Cross ConnectionsAssigning Frame Relay Time Slots to the Network Interface Value Meaning Frame Relay Network Time Slot Assignment Screen ExampleTime Slot Assignment Rule Frame Relay Network 1 Assignment Select Frame Relay Network Assignments Assigning the Synchronous Data Port to Network Time Slots Synchronous Data Port Assignment Screen ExampleSync Data Port Assignment Clearing Assignments Interface Frame Relay Options 1 Configuring Frame Relay for an Interface LMI Parameters Interface Frame Relay Options 2 Frame Relay DS0s Base Rate Interface Frame Relay Options 3 Main Menu→ Configuration→ Network/Data Port→ Dlci Records Manually Configuring Dlci RecordsDlci Type Possible Settings Standard, Multiplexed Dlci Record Options 1 CIR bps Dlci Record Options 2Committed Burst Size Bc Bits Excess Burst Size Bits Dlci Record Options 3 Dlci PriorityOutbound Management Priority Configuring PVC Connections Main Menu → Configuration → PVC ConnectionsPVC Connection Options 1 Destination Link PVC Connection Options 2Destination Dlci Destination Edlci Configuring Node IP Information Setting Up Management and Communication Options Node IP Options 1 Node IP Options 2 TS Access Management Link Node IP Options 3 TS Access Configuring Management PVCs 10. Management PVC Options 1Name Primary Link Possible Settings Net1-FR1, Port-1, Clear 10. Management PVC Options 2Set DE 10. Management PVC Options 3 Primary DlciPrimary Edlci Name 1 Access Configuring General Snmp Management11. General Snmp Management Options 1 Snmp Management Configuring Telnet and/or FTP Session Support 11. General Snmp Management Options 212. Telnet and FTP Session Options 1 12. Telnet and FTP Session Options 2 Inactivity Timeout 12. Telnet and FTP Session Options 3 FTP Login RequiredDisconnect Time Minutes FTP Session Access Type Configuring Snmp NMS Security13. Snmp NMS Security Options NMS IP Validation 14. Snmp Traps Options 1 Configuring Snmp TrapsSnmp Traps Number of Trap Managers Enterprise Specific Traps 14. Snmp Traps Options 2 Link Traps Possible Settings Disable, Up, Down, Both 14. Snmp Traps Options 3Rmon Traps Configuring the Ethernet Port 15. Ethernet Port Options 1Interface Status Proxy ARP 15. Ethernet Port Options 2 16. Communication Port Options 1 Configuring the Communication PortPort Use Character Length 16. Communication Port Options 2 Login RequiredStop Bits Ignore Control Leads 16. Communication Port Options 3 RIP 16. Communication Port Options 4 External Modem Commands Configuring the COM Port to Support an External ModemDial-In Access 17. External Modem COM Port Options Configuration Security and Logins Controlling Asynchronous Terminal Access Limiting Access Set the configuration option Controlling Telnet or FTP Access Controlling External COM Port Device Access Limiting Telnet Access Limiting FTP Access Limiting Telnet or FTP Access Over the TS Management Link Disabling Snmp Access Controlling Snmp Access Assigning Snmp Community Names and Access Levels Limiting Snmp Access Through IP Addresses Creating a Login Main Menu → Control → Administer LoginsField Enter Deleting a Login Modifying a Login Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Viewing LEDs and Control Leads Main Menu → Status → Display LEDs and Control LeadsDisplay LEDs & Control Leads Screen General Status LEDs 1 Label Indication Color What It Means LED Descriptions Network Interface LEDs Label Indication Color What It Means General Status LEDs 2 Label Indication Color What It Means User Data Port LED Label Indication Color What It Means Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network Interface Device Messages 1 What It Indicates What To Do Device Messages See Changing Software Device Messages 2 What It Indicates What To Do Device Messages 3 What It Indicates What To Do Software Device Messages 4 What It Indicates What To Do Changes? prompt Device Messages 5 What It Indicates What To Do Status Information Status MenuStatus Last System Reset Date and Time Self-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Self-Test Results Messages Health and Status Messages 1 What It Indicates Health and Status Messages Frame relay link Health and Status Messages 2 What It Indicates Frame relay link 1, 2 Health and Status Messages 3 What It Indicates Test Status Messages 1 What It Indicates Test Status Messages Test Status Messages 2 What It Indicates Network LMI-Reported DLCIs StatusMain Menu → Status → LMI Reported DLCIs LMI-Reported DLCIs Status Screen Example Network LMI-Reported DLCIs Status Field What It Indicates Main Menu → Status → PVC Connection Status PVC Connection StatusPVC Connection Status Screen Example 10. PVC Connection Status 1 Field 10. PVC Connection Status 2 Field What It Indicates Displaying Network Time Slot Assignments Time Slot Assignment StatusMain Menu → Status → Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen Example Cross Connect Status Field Indicates Bottom Main Menu → Status → IP Routing Table IP Routing TableIP Routing Table Screen Example 11. IP Routing Table Values 1 Column What It Indicates 11. IP Routing Table Values 2 Column What It Indicates Main Menu → Status → Performance Statistics Performance StatisticsPerformance Statistics Menu Performance Statistics Performance Statistics → Clear All Statistics Clearing Performance StatisticsPerformance Statistics → Frame Relay Performance Statistics → ESF Line Service Level Verification Performance Statistics Average round trip latency is measured every SLV sampling Dlci Performance Statistics Main Menu → Status → Performance Statistics → Dlci13. Dlci Performance Statistics 1 What It Indicates CIR&EIR 13. Dlci Performance Statistics 2 What It Indicates Frame Relay Performance Statistics Frame Relay ErrorsMain Menu → Status → Performance Statistics → Frame Relay 14. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors contd 14. Frame Relay Performance Statistics 2 What It IndicatesFrame Relay LMI 14. Frame Relay Performance Statistics 3 What It Indicates Frame Relay Hdlc Errors ESF Line Performance Statistics Main Menu → Status → Performance Statistics → ESF LineTo select intervals You must enter an interval or time on ±LOFC±± ESF Line Performance Statistics Screen Example UAS Statistic What It Indicates Main Menu → Status → Performance Statistics → Ethernet Ethernet Performance Statistics Main Menu → Status → Trap Event Log Trap Event LogTrap Event Log Screen Example Trap Event LOG FTP File Transfers Dir directory Command Definition If the message displayed is Then Upgrading System Software Changing Software Determining Whether a Download Is Completed If retrieving Then Transferring Collected Data Troubleshooting Indicators See Problem Indicators Resetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power If selecting Following occurs Restoring Communication with a Misconfigured Unit Troubleshooting Management Link Feature LMI Packet Capture Utility FeatureMain Menu → Control → LMI Packet Capture Utility LMI Packet Capture Utility → Display LMI Trace Log LMI Trace Log ExampleLMI Trace LOG Alarm Conditions 1 What It Indicates What To Do Alarms Operational appears Alarm Conditions 2 What It Indicates What To Do Alarm Conditions 3 What It Indicates What To Do Alarm Conditions 4 What It Indicates What To Do Device Problems Troubleshooting TablesDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event Log With a Misconfigured Unit Device Problems 2 Symptom Possible Cause Solutions Frame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC Problems Tests Available Test Menu ExampleTest Test Timeout Feature When the status of a test is Only command available isStarting and Stopping a Test Aborting All Tests PVC Tests PVC Tests Screen ExampleNetwork PVC Tests Send Pattern PVC LoopbackMain Menu → Test → Network PVC Tests Main Menu → Test → Data Port PVC Tests Connectivity Monitor Pattern Physical Tests Screen Example Physical Tests Main Menu → Test → Network Physical Tests Line Loopback Payload Loopback Repeater Loopback Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Qrss Send and Monitor Pattern Tests Main Menu → Test → Data Port Physical Tests DTE Loopback Main Menu → Test → IP Ping IP Ping Test Procedure Main Menu → Test → Lamp Test Lamp Test OpenLane Support of FrameSaver Devices OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver Flex and SLV Support To Find Your License Key Number Ordering Flex SLV Activations Activation Certificate Administering and Managing Flex SLV Activations Checking Activation Certificate Status Entering an Activation Certificate Scheduling Activations Cancelling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations July Setting Up NetScout Manager Plus for FrameSaver Devices Preparation AlarmsProperties User history Configuring NetScout Manager Plus Procedure Adding SLV Alarms Using a Template Editing Alarms 9123-A2-GB20-10 July Adding SLV Alarms Manually Paradyne Field Select or Enter Creating History Files Procedure Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Installing the User-Defined History Files Monitoring a DLCIs History Data July 9123-A2-GB20-10 July Monitoring the Agent Using NetScout Manager Plus Procedure Setting Up NetScout Manager Plus for FrameSaver Devices Setting Up Network Health for FrameSaver Devices Installation and Setup of Network Health Discovering FrameSaver Elements Configuring the Discovered Elements Grouping Elements for Reports About Service Level Reports Generating Reports for a GroupAbout At-a-Glance Reports Reports Applicable to Flex and SLV Devices About Trend ReportsPrinted Reports July 9123-A2-GB20-10 July Setting Up Network Health for FrameSaver Devices Menus Menu Hierarchy Status Menu Hierarchy Frame Relay Mode Easy Install Auto-Configuration Data Ports Assignment Menu Hierarchy Leased Line Mode Control Menu Hierarchy Snmp MIBs and Traps, Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB Support System Group mib-2 FrameSaver Units sysDescr systemFrameSaver Units sysObjectID system Paradyne Indexes to the Interface Table ifTable Interfaces Group mib-2Physical Layer Frame Relay Logical Layer NetScout Indexes to the Interface Table ifTable Rmon Logical LayerFor the DTE Examples Standards Compliance for Snmp Traps Trap warmStart Trap authenticationFailureTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown MIB Physical Sublayer Logical Link Sublayer Physical Sublayer contd DevHealthAndStatus Traps enterprise-Specific SLVs devFrExt.mib Placeholder Traps RMON-Specific Event Defaults Rmon Alarm and Event DefaultsEventIndex EventDescription EventType EventCommunity Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults ± Paradyne Area Dlci Alarm Defaults ± NetScout Area Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.2.1 6.1.2.1.2.10.32.2.16.1.4.1.1795.2.24.2 Dlci CIR 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4.4.2 Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 Snmp MIBs and Traps, and Rmon Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Rear Panel Connectors, Cables, Pin Assignments Canadian T1 Line Interface Cable Feature No -F1-510 T1 Network Cable Feature No -F1-500T1 Network Interface Function Circuit Direction Pin Number Signal Direction Pin # COM Port Connector Pin Standard EIA-232-D Crossover Cable AT Command String To configure the modem to Signal Data Port ConnectorStandard V.35 Straight-through Cable Direction Pin Socket Ethernet Port Connector Connectors, Cables, and Pin Assignments Technical Specifications T1 Network Interface COM PortEthernet Port Data Port FrameSaver Flex SLV Upgrade Description Model / Feature NumberEquipment List Equipment Optional Features Description Part Number Feature NumberCables NMS Products Numbers Index IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8 IN-9 IN-10