Data Port Physical Interface Options 2 | Paradyne 9123 manual

Configuration

Table 3-5. Data Port Physical Interface Options (2 of 2)

Monitor RTS (Control)

Possible Settings: Enable, Disable

Default Setting: Enable

Specifies whether the state of the Request To Send (RTS) circuits on the user data port will be used to determine when valid data communication is possible with the DTE. When the RTS off condition is detected, CTS is deasserted, LMI is declared down, and no further transfer of frame relay data can occur on this interface.

Enable ± Interchange circuit CA (ITU 105) ± RTS is monitored to determine when valid data communication is possible with the DTE.

Disable ± RTS is not monitored. RTS is assumed to be asserted and data is being transmitted, regardless of the state of the lead.

Port (DTE) Initiated Loopbacks

Possible Settings: Local, Disable

Default Setting: Disable

Allows a local external DTE Loopback to be started or stopped via the port's attached data terminal equipment using the port's interchange lead LL (ITU 141).

Local ± The DTE attached to the port controls the local external DTE Loopback.

Disable ± The DTE attached to the port cannot control the local external DTE Loopback.

3-28

July 2000

9123-A2-GB20-10

Image 60

Paradyne 9123 manual Data Port Physical Interface Options 2, Monitor RTS Control, Port DTE Initiated Loopbacks

Contents

FrameSaver Flex Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuration Security and Logins Troubleshooting Setting Up NetScout Manager Plus for FrameSaver Devices Index About This Guide Purpose and Intended AudienceDocument Organization Setting Up OpenLane for FrameSaver Devices. Identifies Where installation and setup information is located and howSetting Up NetScout Manager Plus for FrameSaver Devices. Describes setup of the NetScout Manager Plus Product-Related Documents When viewing this manual online. Click on Conventions UsedTo indicate a hyperlink to additional information Highlighted text About the FrameSaver Flex System OverviewSystem Overview FrameSaver Flex Feature Sets Feature Feature Set Basic Advanced Flex Flex SLV Basic Flex Features 9123-A1-211 9123-A1-213 Feature 9123-A1-221 9123-A1-223 Maximum Number of PVCs and Management PVCs SupportedModels Through Connections PVCs Dedicated Management PVCs July Advanced Flex SLV Features OpenLane SLM System NetScout Manager Plus and NetScout Probes About the FrameSaver Flex User Interface Basic Operation Procedure Logging On If your login was Then Main Menu SelectMain Menu Service Level Verification System Options Screen Work AreasScreen Format Description Navigating the Screens Keyboard KeysPress Function Keys Select For the screen Press Enter to Function Switching Between Screen Areas Selecting from a Menu Selecting a Field Entering InformationExample User Interface and Basic Operation Configuration Configuration Basic Configuration Configuration MenuConfiguration EDIT/DISPLAY Configuration Option Areas Configuration Option Area Description Accessing and Displaying Configuration Options Main Menu → Configuration Changing Configuration Options Configuration → PVC Connections Saving Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example If the selection is Unit is configured to operate Default Setting Up So the Router Can Receive RIP Entering System Information Setting the System ClockConfiguration → Data Ports → Dlci Records Main Menu → Control → System Information Setting Up Auto-Configuration Main Menu → Auto-ConfigurationAuto-Configuration Screen Example AUTO-CONFIGURATION Selecting a Frame Relay Discovery Mode Main Menu → Auto-Configuration → Frame Relay Discovery ModeDiscovery Mode Configuration Description 9123-A2-GB20-10 July Automatically Removing a Circuit Setting Up Back-to-Back Operation Changing Operating ModeMain Menu → Control → Change Operating Mode Configuration Option Tables Configuring the Overall System Configuring Frame Relay and LMI for the System Main Menu → Configuration → System → Frame Relay and LMISystem Frame Relay and LMI Options 1 LMI Behavior LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 System Frame Relay and LMI Options 2Traffic Policing LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 System Frame Relay and LMI Options 3 Configuring Service Level Verification Options Service Level Verification Options 1 Service Level Verification Options 2 SLV Timeout Clearing Event ThresholdSLV Packet Size bytes Configuring General System Options Main Menu → Configuration → System→ GeneralGeneral System Options Configuring the Physical Interfaces Configuring the Network InterfaceMain Menu → Configuration → Network → Physical Network Physical Interface Options 1 Network Physical Interface Options 2 Bit StuffingTransmit Timing Network Initiated LLB Network Initiated Dclb Possible Settings Disable, V.54&ANSI Network Physical Interface Options 3Network Initiated PLB Ansi Performance Report Messages Network Physical Interface Options 4 Circuit Identifier Configuring the User Data Port Main Menu → Configuration → Data Ports → PhysicalData Port Physical Interface Options 1 Transmit Clock Source Data Port Physical Interface Options 2 Monitor RTS ControlPort DTE Initiated Loopbacks Main Menu → Easy Install → Time Slot Assignment Screen Assigning Time Slots/Cross ConnectionsAssigning Frame Relay Time Slots to the Network Interface Frame Relay Network Time Slot Assignment Screen Example Value MeaningTime Slot Assignment Rule Frame Relay Network 1 Assignment Select Frame Relay Network Assignments Assigning the Synchronous Data Port to Network Time Slots Synchronous Data Port Assignment Screen ExampleSync Data Port Assignment Clearing Assignments Configuring Frame Relay for an Interface Interface Frame Relay Options 1 Interface Frame Relay Options 2 LMI Parameters Interface Frame Relay Options 3 Frame Relay DS0s Base Rate Manually Configuring Dlci Records Main Menu→ Configuration→ Network/Data Port→ Dlci RecordsDlci Type Possible Settings Standard, Multiplexed Dlci Record Options 1 Dlci Record Options 2 CIR bpsCommitted Burst Size Bc Bits Excess Burst Size Bits Dlci Record Options 3 Dlci PriorityOutbound Management Priority Configuring PVC Connections Main Menu → Configuration → PVC ConnectionsPVC Connection Options 1 PVC Connection Options 2 Destination LinkDestination Dlci Destination Edlci Setting Up Management and Communication Options Configuring Node IP Information Node IP Options 1 TS Access Management Link Node IP Options 2 TS Access Node IP Options 3 Configuring Management PVCs 10. Management PVC Options 1Name Primary Link Possible Settings Net1-FR1, Port-1, Clear 10. Management PVC Options 2Set DE 10. Management PVC Options 3 Primary DlciPrimary Edlci Configuring General Snmp Management Name 1 Access11. General Snmp Management Options 1 Snmp Management Configuring Telnet and/or FTP Session Support 11. General Snmp Management Options 212. Telnet and FTP Session Options 1 Inactivity Timeout 12. Telnet and FTP Session Options 2 FTP Login Required 12. Telnet and FTP Session Options 3Disconnect Time Minutes FTP Session Configuring Snmp NMS Security Access Type13. Snmp NMS Security Options NMS IP Validation Configuring Snmp Traps 14. Snmp Traps Options 1Snmp Traps Number of Trap Managers 14. Snmp Traps Options 2 Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both 14. Snmp Traps Options 3Rmon Traps Configuring the Ethernet Port 15. Ethernet Port Options 1Interface Status 15. Ethernet Port Options 2 Proxy ARP Configuring the Communication Port 16. Communication Port Options 1Port Use Character Length Login Required 16. Communication Port Options 2Stop Bits Ignore Control Leads 16. Communication Port Options 3 16. Communication Port Options 4 RIP Configuring the COM Port to Support an External Modem External Modem CommandsDial-In Access 17. External Modem COM Port Options Configuration Security and Logins Limiting Access Controlling Asynchronous Terminal Access Set the configuration option Controlling External COM Port Device Access Controlling Telnet or FTP Access Limiting Telnet Access Limiting FTP Access Limiting Telnet or FTP Access Over the TS Management Link Controlling Snmp Access Disabling Snmp Access Assigning Snmp Community Names and Access Levels Limiting Snmp Access Through IP Addresses Creating a Login Main Menu → Control → Administer LoginsField Enter Modifying a Login Deleting a Login Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Viewing LEDs and Control Leads Main Menu → Status → Display LEDs and Control LeadsDisplay LEDs & Control Leads Screen LED Descriptions General Status LEDs 1 Label Indication Color What It Means General Status LEDs 2 Label Indication Color What It Means Network Interface LEDs Label Indication Color What It Means Control Lead Descriptions User Data Port LED Label Indication Color What It MeansAdditional Control Leads Label Indication What It Means Network Interface Device Messages Device Messages 1 What It Indicates What To Do Device Messages 2 What It Indicates What To Do See Changing Software Device Messages 3 What It Indicates What To Do Device Messages 4 What It Indicates What To Do Software Device Messages 5 What It Indicates What To Do Changes? prompt Status Information Status MenuStatus Self-Test Results Messages Last System Reset Date and Time Last System Reset Date and TimeSystem and Test Status Messages Self-Test Results Messages Health and Status Messages Health and Status Messages 1 What It Indicates Health and Status Messages 2 What It Indicates Frame relay link Health and Status Messages 3 What It Indicates Frame relay link 1, 2 Test Status Messages Test Status Messages 1 What It Indicates Network LMI-Reported DLCIs Status Test Status Messages 2 What It IndicatesMain Menu → Status → LMI Reported DLCIs LMI-Reported DLCIs Status Screen Example Network LMI-Reported DLCIs Status Field What It Indicates PVC Connection Status Main Menu → Status → PVC Connection StatusPVC Connection Status Screen Example 10. PVC Connection Status 1 Field 10. PVC Connection Status 2 Field What It Indicates Time Slot Assignment Status Displaying Network Time Slot AssignmentsMain Menu → Status → Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen Example Cross Connect Status Field Indicates Bottom IP Routing Table Main Menu → Status → IP Routing TableIP Routing Table Screen Example 11. IP Routing Table Values 1 Column What It Indicates 11. IP Routing Table Values 2 Column What It Indicates Performance Statistics Main Menu → Status → Performance StatisticsPerformance Statistics Menu Performance Statistics Clearing Performance Statistics Performance Statistics → Clear All StatisticsPerformance Statistics → Frame Relay Performance Statistics → ESF Line Service Level Verification Performance Statistics Average round trip latency is measured every SLV sampling Dlci Performance Statistics Main Menu → Status → Performance Statistics → Dlci13. Dlci Performance Statistics 1 What It Indicates 13. Dlci Performance Statistics 2 What It Indicates CIR&EIR Frame Relay Errors Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics → Frame Relay 14. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors contd 14. Frame Relay Performance Statistics 2 What It IndicatesFrame Relay LMI Frame Relay Hdlc Errors 14. Frame Relay Performance Statistics 3 What It Indicates ESF Line Performance Statistics Main Menu → Status → Performance Statistics → ESF LineTo select intervals You must enter an interval or time on ESF Line Performance Statistics Screen Example ±LOFC±± Statistic What It Indicates UAS Ethernet Performance Statistics Main Menu → Status → Performance Statistics → Ethernet Trap Event Log Main Menu → Status → Trap Event LogTrap Event Log Screen Example Trap Event LOG FTP File Transfers Command Definition Dir directory Upgrading System Software If the message displayed is Then Determining Whether a Download Is Completed Changing Software Transferring Collected Data If retrieving Then Troubleshooting Problem Indicators Indicators See Resetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power Restoring Communication with a Misconfigured Unit If selecting Following occurs Troubleshooting Management Link Feature LMI Packet Capture Utility FeatureMain Menu → Control → LMI Packet Capture Utility LMI Packet Capture Utility → Display LMI Trace Log LMI Trace Log ExampleLMI Trace LOG Alarms Alarm Conditions 1 What It Indicates What To Do Alarm Conditions 2 What It Indicates What To Do Operational appears Alarm Conditions 3 What It Indicates What To Do Alarm Conditions 4 What It Indicates What To Do Troubleshooting Tables Device ProblemsDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event Log Device Problems 2 Symptom Possible Cause Solutions With a Misconfigured Unit Frame Relay PVC Problems Frame Relay PVC Problems Symptom Possible Cause Solutions Tests Available Test Menu ExampleTest Test Timeout Feature When the status of a test is Only command available isStarting and Stopping a Test Aborting All Tests PVC Tests PVC Tests Screen ExampleNetwork PVC Tests PVC Loopback Send PatternMain Menu → Test → Network PVC Tests Main Menu → Test → Data Port PVC Tests Monitor Pattern Connectivity Physical Tests Physical Tests Screen Example Line Loopback Main Menu → Test → Network Physical Tests Payload Loopback Repeater Loopback Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Send and Monitor Pattern Tests Qrss DTE Loopback Main Menu → Test → Data Port Physical Tests IP Ping Test Main Menu → Test → IP Ping Procedure Lamp Test Main Menu → Test → Lamp Test OpenLane Support of FrameSaver Devices OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver Flex and SLV Support Ordering Flex SLV Activations To Find Your License Key Number Activation Certificate Administering and Managing Flex SLV Activations Entering an Activation Certificate Checking Activation Certificate Status Scheduling Activations Cancelling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations July Setting Up NetScout Manager Plus for FrameSaver Devices Alarms PreparationProperties User history Configuring NetScout Manager Plus Procedure Adding SLV Alarms Using a Template Editing Alarms 9123-A2-GB20-10 July Adding SLV Alarms Manually Field Select or Enter Paradyne Creating History Files Procedure Installing the User-Defined History Files Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Monitoring a DLCIs History Data July 9123-A2-GB20-10 July Monitoring the Agent Using NetScout Manager Plus Procedure Setting Up NetScout Manager Plus for FrameSaver Devices Setting Up Network Health for FrameSaver Devices Installation and Setup of Network Health Discovering FrameSaver Elements Configuring the Discovered Elements Grouping Elements for Reports About Service Level Reports Generating Reports for a GroupAbout At-a-Glance Reports Reports Applicable to Flex and SLV Devices About Trend ReportsPrinted Reports July 9123-A2-GB20-10 July Setting Up Network Health for FrameSaver Devices Menu Hierarchy Menus Menu Hierarchy Frame Relay Mode Status Auto-Configuration Easy Install Menu Hierarchy Leased Line Mode Data Ports Assignment Control Menu Hierarchy Snmp MIBs and Traps, Rmon Alarm Defaults MIB Support Downloading MIBs and Snmp Traps System Group mib-2 FrameSaver Units sysDescr systemFrameSaver Units sysObjectID system Interfaces Group mib-2 Paradyne Indexes to the Interface Table ifTablePhysical Layer Frame Relay Logical Layer NetScout Indexes to the Interface Table ifTable Rmon Logical LayerFor the DTE Standards Compliance for Snmp Traps Examples Trap authenticationFailure Trap warmStartTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown Physical Sublayer MIB Physical Sublayer contd Logical Link Sublayer Traps enterprise-Specific DevHealthAndStatus SLVs devFrExt.mib Placeholder Traps RMON-Specific Rmon Alarm and Event Defaults Event DefaultsEventIndex EventDescription EventType EventCommunity Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults ± Paradyne Area Dlci Alarm Defaults ± NetScout Area Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.2.1 6.1.2.1.2.10.32.2.16.1.4.1.1795.2.24.2 6.1.4.1.1795.2.24.2.6.9.4 Dlci CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 Snmp MIBs and Traps, and Rmon Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Connectors, Cables, Pin Assignments Rear Panel T1 Network Cable Feature No -F1-500 Canadian T1 Line Interface Cable Feature No -F1-510T1 Network Interface Function Circuit Direction Pin Number COM Port Connector Signal Direction Pin # Standard EIA-232-D Crossover Cable Pin AT Command String To configure the modem to Data Port Connector SignalStandard V.35 Straight-through Cable Direction Pin Socket Ethernet Port Connector Connectors, Cables, and Pin Assignments Technical Specifications COM Port T1 Network InterfaceEthernet Port Data Port Description Model / Feature Number FrameSaver Flex SLV UpgradeEquipment List Equipment Description Part Number Feature Number Optional FeaturesCables NMS Products Index Numbers IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8 IN-9 IN-10