Using the Command Line Interface (CLI)

Syslog Lowest Priority

Integer

1 – 7

RW

syslogpritolog

Logged

 

1 = LOG_ALERT

 

 

 

 

2

= LOG_CRIT

 

 

 

 

3

= LOG_ERR

 

 

 

 

4

= LOG_WARNING

 

 

 

 

5

= LOG_NOTICE

 

 

 

 

6

= LOG_INFO (default)

 

 

 

 

7

= LOG_DEBUG

 

 

Heartbeat Status

Integer

enable (1)

RW

sysloghbstatus

 

 

disable (2) (default)

 

 

Heartbeat Interval (seconds)

Integer

1 – 604800 seconds;

RW

sysloghbinterval

 

 

900 sec. (default)

 

 

NOTE

The Heartbeat parameters are advanced settings not available via the HTTP interface. When Heartbeat is enabled, the AP periodically sends a message to the Syslog server to indicate that it is active. The frequency with which the heartbeat message is sent depends upon the setting of the Heartbeat Interval.

Syslog Host Table

The table described below configures the Syslog hosts that will receive message from the AP. You can configure up to ten Syslog hosts.

 

Name

 

Type

 

Values

 

Access

CLI Parameter

 

Syslog Host Table

 

Table

 

N/A

 

 

 

R

sysloghosttbl

 

Table Index

 

Integer

 

1 – 10

 

 

N/A

index

 

IP Address

 

IpAddress

 

User Defined

 

 

RW

ipaddr

 

Comment (optional)

 

DisplayString

 

User Defined

 

 

RW

cmt

 

Status (optional)

 

Integer

 

enable

 

 

RW

status

 

 

 

 

 

disable

 

 

 

 

 

 

 

 

 

 

 

 

delete

 

 

 

 

 

 

 

Bridge Parameters

 

 

 

 

 

 

 

 

 

 

 

Spanning Tree Parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name

Type

Values

Access

 

CLI Parameter

 

 

Spanning Tree

Group

N/A

R

 

stp

 

 

 

 

Spanning Tree Status

Integer

enable (default)

RW

 

stpstatus

 

 

 

 

 

disable

 

 

 

 

 

 

 

 

Bridge Priority

Integer

0 – 65535

RW

 

stppriority

 

 

 

 

 

32768 (default)

 

 

 

 

 

 

 

 

Maximum Age

Integer

600 – 4000

RW

 

stpmaxage

 

 

 

 

 

(in 0.01 sec intervals;

 

 

 

 

 

 

 

 

 

 

 

i.e., 6 to 40 seconds)

 

 

 

 

 

 

 

 

 

 

 

2000 (default)

 

 

 

 

 

 

 

 

Hello Time

Integer

100 – 1000

RW

 

stphellotime

 

 

 

 

 

(in 0.01 sec intervals;

 

 

 

 

 

 

 

 

 

 

 

i.e., 1 to 10 seconds)

 

 

 

 

 

 

 

 

 

 

 

200 (default)

 

 

 

 

 

 

 

 

Forward Delay

Integer

400 – 3000

RW

 

stpfwddelay

 

 

 

 

 

(in 0.01 sec intervals;

 

 

 

 

 

 

 

 

 

 

 

i.e., 4 to 30 seconds)

 

 

 

 

 

 

 

 

 

 

 

1500 (default)

 

 

 

 

 

 

 

Spanning Tree Priority and Path Cost Table

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name

Type

Values

Access

 

CLI Parameter

 

 

 

Spanning Tree Table

Table

N/A

R

 

stpbl

 

 

 

 

Table Index (Port)

N/A

1 – 15

R

 

index

 

 

 

173

Page 173
Image 173
Proxim AP-2000 Bridge Parameters, Spanning Tree Parameters, Syslog Host Table, Spanning Tree Priority and Path Cost Table