802.11b/g Only Parameters | Proxim AP-2000 guide

Using the Command Line Interface (CLI)

802.11b/g Only Parameters

Name	Type	Values		Access	CLI Parameter
Wireless Operational Mode	Integer	dot11b-only		RW	mode
		dot11g-only
		dot11bg (default)
		dot11g-wifi
Operating Frequency Channel	Integer	1 - 14; available		RW	channel
		channels vary by
		regulatory
		domain/country; see
		802.11g Channel
		Frequencies
Supported Data Rates	Octet String	See Transmit Rate,		R	suppdatarates
		below
Transmit Rate	Integer32	For 802.11b-only mode:		RW	txrate
		0	(auto fallback - default)
		1	Mbits/sec
		2	Mbits/sec
		5.5 Mbits/sec
		11 Mbits/sec
		For 802.11g-only mode:
		0	(auto fallback - default)
		6	Mbits/sec
		9	Mbits/sec
		12 Mbits/sec
		18 Mbits/sec
		24 Mbits/sec
		36 Mbits/sec
		48 Mbits/sec
		54 Mbits/sec
		For 802.11g-wifi and
		802.11bg modes:
		0	(auto fallback - default)
		1	Mbits/sec
		2	Mbits/sec
		5.5 Mbits/sec
		11 Mbits/sec
		6	Mbits/sec
		9	Mbits/sec
		12 Mbits/sec
		18 Mbits/sec
		24 Mbits/sec
		36 Mbits/sec
		48 Mbits/sec
		54 Mbits/sec
Physical Layer Type	Integer	ERP (Extended Rate		R	phytype
		Protocol)
SuperMode	Integer	enable		RW	supermode
		disable (default)
TurboMode	Integer	enable		RW	turbomode
		disable (default)

Note 1: Super Mode must be enabled first on the wireless interface before Turbo Mode can be enabled.

Wireless Distribution System (WDS) Parameters

Name	Type	Values	Access	CLI Parameter
WDS Table	Table	N/A	R	wdstbl
Port Index	Integer	3.1 - 3.6 (Wireless)	R	portindex
Status	Integer	enable, disable	RW	status
Partner MAC Address	PhysAddress	User Defined	RW	partnermacaddr

164

Image 164

Proxim AP-2000 manual 802.11b/g Only Parameters, Wireless Distribution System WDS Parameters

Contents

ORiNOCO AP-2000 Access Point Copyright Contents Viewing Status Information Bridge Monitoring the AP-2000 Troubleshooting the AP-2000 Using the Command Line Interface CLI Other Network Settings CLI Batch File Regulatory Information Introduction to Wireless Networking Document Conventions Introduction Guidelines for Roaming Ieee 802.11 Specifications Command Line InterfaceManagement and Monitoring Capabilities HTTP/HTTPS Interface Snmp Management SNMPv3 Secure Management Getting Started Prerequisites System Requirements GHz Antenna Adapter or AP-2000 11a Upgrade KitProduct Package Hardware Installation AP-2000 with Active Ethernet AP-2000 with Power Supply Connect an Ethernet cable from an AE hub to the AP Install the power supply Power LED turns green when the unit is operational GHz or AP-2000 11a Upgrade Kit 10 Remove the AP cover 12 Replace cover ScanTool Instructions InitializationScanTool 13 Scan List Setup Wizard Setup Wizard InstructionsClick LAN Settings Set IP Address Type to Static 15 Enter Network Password Getting Started Download the Latest Software Setup your Tftp Server Additional Hardware Features Installing the AP in a PlenumInstalling/Removing the Metal Faceplate Enter the command download tftpaddr filename img LED Indicators Active Ethernet Related Topics Viewing Status Information Logging into the Http Interface System Status System Status Screen Performing Advanced Configuration Configuring the AP Using the HTTP/HTTPS Interface Performing Advanced Configuration Dynamic DNS Support Access Point System Naming ConventionSystem IP Configuration NetworkBasic IP Parameters DNS Client Dhcp Server Configuration Screen Dhcp Server Link Integrity Start IP Address End IP AddressComment optional Target IP Address Comment optional Operational Mode 8Wireless-A and Wireless-B Ethernet Interfaces Operational Mode 8Wireless-A and Wireless-BOperational Mode Selection Wireless a 802.11a RTS/CTS Medium Reservation Wireless Service StatusDynamic Frequency Selection DFS Wireless 802.11b Traps Generated During Wireless Service Shutdown and Resume Distance Between APs Multicast Rate Small Cell Large Cell Wireless 802.11b/g 1 Mbits/s and 11 Mbits/s Multicast Rates Wireless Distribution System WDS Bridging WDS Click on Interfaces Wireless-A or Wireless-B WDS Edit Entry Screen Ethernet Management PasswordsIP Access Table Services Snmp SettingsHttp Access Https Access 10 Management Services Configuration Screen Telnet Configuration Settings Secure Shell SSH SettingsSSH Session Setup Configuring SSH Click Commands Update AP via Http or via Tftp Uploading Externally Generated Host Keys Serial Configuration Settings Radius Based Management Access Set up Automatic Configuration for Static IP Automatic Configuration AutoConfigAuto Configuration and the CLI Batch File Set up Automatic Configuration for Dynamic IP 12 Automatic Configuration Screen 13 Dhcp Options Setting the Boot Server Host Name Hardware Configuration Reset Chrp Configuration Reset via Serial Port During Bootup Click Configure -Management -CHRD Configuring Hardware Configuration ResetProcedure to Reset Configuration via the Serial Interface Filtering Ethernet ProtocolStatic MAC Select the Filter Operation Type 16 Static MAC Configuration Screen Static MAC Filter Examples Prevent Two Specific Devices from Communicating Advanced TCP/UDP PortAdding TCP/UDP Port Filters Click Add under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Click Edit under the TCP/UDP Port Filter Table heading Groups AlarmsConfiguration Trap Group Wireless Interface/Card Trap Group Security Trap GroupOperational Trap Group Flash Memory Trap Group Bridge MIB RFC 1493 Alarms Tftp Trap GroupImage Trap Group RFC 1215-Trap Alarm Host Table Setting Syslog Event NotificationsConfiguring Syslog Event Notifications Syslog Syslog Messages Following messages are supported in the AP Rogue Access Point Detection RAD RAD Configuration Requirements Configuring RAD 19 Rogue Access Point Detection Screen Bridge Spanning TreeStorm Threshold Intra BSS QoS Quality of Service Packet Forwarding Pkt Fwd Radius Servers per Authentication Mode and per Vlan Radius Profiles RADIUS-based Vlan Assignment Configuring Radius ProfilesRadius Servers Enforcing Vlan Access Control Adding or Modifying a Radius Server Profile 22 Add Radius Server Profile MAC Access Control Via Radius Authentication 802.1x Authentication using Radius Radius Accounting Session Length Vlan Overview SSID/VLAN/SecurityManagement Vlan Typical User Vlan Configurations Vlan Workgroups and Traffic Management Control Access to the AP Provide Access to a Wireless Host in the Same WorkgroupDisable Vlan Management Click Configure SSID/VLAN/Security MAC Access Configuring MAC Access WEP Encryption 802.1x AuthenticationSecurity Profiles Wi-Fi Protected Access WPA Authentication Process Authentication Protocol Hierarchy VLANs and Security Profiles Configuring Security Profiles Click Configure -SSID/VLAN/Security -Security ProfileNon Secure Station WEP Station 802.1x Station WPA StationWPA-PSK Station 802.11i Station 27 Security Profile Table Add Entries Wireless-A and Wireless-B Click on SSID/VLAN/Security Wireless-A or Wireless-B 30 SSID/VLAN Edit Entries Screen Vlan Protocol Disabled Performing Advanced Configuration Adding or Modifying an SSID/VLAN with Vlan Protocol Enabled Click SSID/VLAN/Security Wireless-A or Wireless-B 33 SSID/VLAN Add Entries Screen Vlan Protocol Enabled 34 SSID/VLAN Edit Entries Screen Vlan Protocol Enabled Broadcast Ssid and Closed System Monitoring the AP-2000 Monitoring the AP-2000 Version Component Name Icmp IP/ARP Table Learn Table Iapp Radius 106 Station Statistics Enabling and Viewing Station StatisticsRefreshing Station Statistics Description of Station Statistics 108 Performing Commands Performing Commands Image Error Checking during File Transfer Introduction to File Transfer via Tftp or HttpTftp File Transfer Guidelines Http File Transfer Guidelines Update AP via Tftp Update AP via Tftp Command Screen Update AP via Http Update AP via Http Command Screen 114 Retrieve File via Tftp Command Screen Retrieve File via Tftp Retrieve File via Http Command Screen Retrieve File via Http 117 Reboot 13 Reboot Command Screen Reset 14 Reset to Factory Defaults Command Screen Help Link Program Files/ORiNOCO/AP/HTML/index.htm Troubleshooting the AP-2000 Troubleshooting Concepts Basic Software Setup and Configuration Problems Symptoms and SolutionsConnectivity Issues Http browser or Telnet Interface Does Not Work Html Help Files Do Not AppearTelnet CLI Does Not Work Tftp Server Does Not Work Client Connection Problems Vlan Operation Issues Recovery Procedures Active Ethernet AEAP Does Not Work There Is No Data Link Reset to Factory Default Procedure Forced Reload Procedure Preparing to Download the AP Image Download a New Image Using ScanToolDownload Procedure Download a New Image Using the Bootloader CLI Setting IP Address using Serial Port Initializing the IP Address using CLIHardware and Software Requirements Attaching the Serial Port Cable 130 Tftp Server Radius Authentication ServerRelated Applications General Notes Prerequisite Skills and KnowledgeNotation Conventions Important Terminology Navigation and Special Keys Command Line Interface CLI VariationsCLI Error Messages Bootloader CLI Figure A-1 Results of help bootloader CLI command CLI Command Types Operational CLI Commands? List Commands Example 1. Display Command list Example 3b. Display parameters based on letter sequence Example 3. Display parameters for set and showExample 3a. Display every parameter that can be changed Done, exit, quit DownloadHelp Example 4. Display Prompts for Successive Parameters Reboot HistoryPasswd Search Parameter Control Commands Show CLI CommandSet CLI Command Upload Configuring Objects that Require Reboot Set and show Command ExamplesExample 1 Set the Access Point IP Address Parameter Following elements require reboot ipaddr Example 5 Show the Group Parameters Example 4 Enable, Disable, or Delete a table entry or rowExample 3 Modify a table entry or row Example 6 Show Individual and Table Parameters Using Tables & User StringsWorking with Tables Configuring the AP using CLI commands Using StringsLog into the AP using HyperTerminal Log into the AP using Telnet Set Basic Configuration Parameters using CLI Commands Change PasswordsSet System Name, Location and Contact Information Set Static IP Address for the AP Set Network Names for the Wireless Interface Configure Ssid Network Name and Vlan Pairs, and Profiles 146 Other Network Settings Download an AP Configuration File from your Tftp ServerBackup your AP Configuration File Set up Auto Configuration Configure the AP as a Dhcp Server Configure the DNS ClientMaintain Client Connections using Link Integrity Change your Wireless Interface Settings Operational Mode Enable/Disable Closed SystemShutdown/Resume Wireless Service Enable/Disable Interference Robustness 802.11b Only Set Ethernet Speed and Transmission Mode Set Interface Management Services Configure Syslog Configure Intra BSSConfigure Secure Socket Layer Https Set Telnet Session Timeouts Configure MAC Access Control Setup MAC Address Access ControlAdd an Entry to the MAC Access Control Table Disable or Delete an Entry in the MAC Access Control Table Configure Radius Authentication servers Set Radius Parameters 154 Set Rogue Access Point Detection RAD Parameters Figure A-16 Results of show rad CLI command Set Hardware Configuration Reset Parameters Enable Vlan ManagementCLI Monitoring Parameters Parameter Tables 157 Name Type Values Access CLI Parameter System Parameters IP Configuration Parameters DNS Client for Radius Name ResolutionNetwork Parameters Inventory Management Information Dhcp Server Parameters Dhcp Server table for IP pools Link Integrity Parameters Link Integrity IP Target Table Wireless Interface Parameters Interface ParametersCommon Parameters to 802.11a, 802.11b, and 802.11b/g APs 802.11a Only Parameters 802.11b Only Parameters 802.11b Channel Frequencies Wireless Distribution System WDS Parameters 802.11b/g Only Parameters Wireless Interface SSID/VLAN/Profile Parameters Wireless Distribution System WDS Security Table Parameters Management Parameters Ethernet Interface ParametersSecure Management Parameters Snmp Parameters Telnet Parameters Serial Port Parameters Radius Based Management Access Parameters SSH Parameters Tftp Server Parameters Auto Configuration ParametersIP Access Table Parameters Filtering Parameters Ethernet Protocol Filtering ParametersStatic MAC Address Filter Table Ethernet Protocol Filtering Table Proxy ARP Parameters IP ARP Filtering ParametersBroadcast Filtering Table TCP/UDP Port Filtering Syslog Parameters Alarms ParametersSnmp Table Host Table Parameters Bridge Parameters Spanning Tree ParametersSyslog Host Table Spanning Tree Priority and Path Cost Table Storm Threshold Parameters Intra BSS Subscriber BlockingPacket Forwarding Parameters Storm Threshold Table Radius Parameters MAC Access Control ParameterSecurity Parameters VLAN/SSID Parameters Rogue Access Point Detection RAD ParametersHardware Configuration Reset Configuring a Security Profile with WEP Security Mode Configuring a Security Profile with 802.1x Security ModeConfiguring a Security Profile with WPA Security Mode Set secprofiletbl index secmode nonsecure status enable Configuring a Security Profile with WPA-PSK Security Mode Configuring a Security Profile with 802.11i Security ModeOther Parameters Iapp Parameters Auto Configuration and the CLI Batch File CLI Batch FileCLI Batch File Format and Syntax Sample CLI Batch File Reboot Behavior CLI Batch File Error Log Ascii Character Chart Management Functions Software FeaturesNumber of Stations per BSS Security Functions Medium Access Control MAC FunctionsAdvanced Bridging Functions Hardware Specifications Advanced Wireless FunctionsPhysical Specifications Network Functions Radio Specifications Ethernet InterfaceSerial Port Interface Active Ethernet Interface 802.11a Channel Frequencies FCC Etsi Telec Asia 802.11b Channel Frequencies 802.11g Channel Frequencies Wireless Communication Range 802.11b 802.11a 5 GHz Upgrade Kit 802.11a 11a Upgrade Kit 802.11b/g Range International For the U.S. and CanadaEurope, the Middle East, and Africa Emea Warranty Coverage Repair or ReplacementLimitations of Warranty Support Procedures Ask a Question or Open an Issue Other InformationSearch Knowledgebase Other Adapter Cards Regulatory Information Important Safety Instructions Information to the User Wireless LAN and your Health Regulatory Information Informations pour l’utilisateur Instructions Importantes Concernant LA Securite Réseaux sans fil et votre santé Informations sur les réglementations Informazioni per l’utente Norme DI Sicurezza Importanti Wireless LAN e la salute Informazioni legali Informationen für den Benutzer Wichtige Sicherheitshinweise Funk-LAN und gesundheitliche Sicherheit Rechtliche Hinweise Información para el usuario Instrucciones DE Seguridad Importantes LAN inalámbrica y su salud Información sobre normativas これらの指示書を保管してください無線 LAN と人体への影響 United States FCC Information Modifications Industry Canada IC Product SafetyCanada IC Information Europe Information 210 Japan Information Association of Radio Industries and Businesses Arib AP-II E South Korea InformationPC24E-H-FC Radio Approvals Certifications radioOmologazioni radio Funkgenehmigungen Australia Alpha-1 A13QBF For indoor use only Austria ÖsterreichR0167 SRD3a G13ENE-PC PC24E-H-FC PC24E-H-ET-L PC24E-H-ET A19PCE-PC AP-AG-AT-01AP-AG-AT-02 B11FNF C38WCW A04VBA-PC 219 AP-AT-AG-01 AP-AT-AG-02 France Restricted frequency band On French territoryPC24E-H-FR-L PC24E-H-FR PC24E-H-ET Cetecom D810069L 223 224 225 Pays Émetteur Radio Numéro du Permis Restrictions Paese G05INI-PCPC24E-H-ET-L CEPT-RLAN PC24E-H-ET CEPT-RLAN PC24E-H-FC Telec NYCA0010 Telec 01NYDA1121Telec 01NYDA1122 G13GNJ-PC Telec 03YNDA0185 Telec 03GZDA0150 228 229 PC24E-11-FC/R Cofetel G11FNF-PC CofetelRTIPRPC02-369 A13QBF-PC Cofetel PCPPRAL03-095 AP-AG-AT-01 RCPPRAP03-537AP-AG-AT-02 RCPPRAP03-537 PTIPRAL03-094 232 PC24E-H-FC RFS PC24E-H-ET-L RFS G11FNF-PC Gost ME96 G13ENE-PC PC24E-H-FC/RPC24E-H-ET-L PC24E-H-ET/R PC24E-H-FC IDA PC24E-H-ET IDA PMREQ-WLAN-B-0934G13ENE-PC IDA A09SBS-PC IDA 236 237 238 Switzerland AP-700 For indoor use only Suisse Pour usage intérieur uniquementSchweiz Svizzera A09TBT-PC USA PC24E-H-FC FCC ID IMRWLPCE24H IMRWLPCE2411RFCC ID IMRWLPC2411R USA G11FNF-PC HZB-G11FNFPC FCC ID HZB-B11FNF USA FCC ID HZB-G11FNF USAFCC ID HZB-A13QBF AP-AG-AT-01 IXMAPAGAT01 242 243 244