Honeywell 3.5, ZyAIR G-3000 manual Connecting the Transformer, Installing the Control, 3-23, Uvst

Section 3 - Installing the Control

UVCM AND UVST SUMMARY OF CONNECTIONS

Refer to UVS Installation and Setup Guide K4214 for complete information

NOTE 1: CONNECT TO PROPER EARTH GROUND.

SW

SWITCH BANK 1

SW

SWITCH BANK 2

1

UVST 1 AUX AUDIO, ON = ENABLED

1

FUTURE USE, SET TO ON

NOTE 2: POWER MAY ALSO BE SUPPLIED BY A LISTED CLASS 2

POWER SUPPLY RATED 12VDC, MIN 600mA CONNECTED TO THE

2

UVST 2 AUX AUDIO, ON = ENABLED

2

FUTURE USE, SET TO ON

UVCM +12VDC IN AND GND TERMINALS.

3

UVST 3 AUX AUDIO, ON = ENABLED

3

TELEPHONE RING, ON = ENABLED

4

UVST 4 AUX AUDIO, ON = ENABLED

4

END USER VOICE, ON = DISABLED

NOTE 3: SOME CONTROL PANELS USE BUILT-IN TRIGGER AND SOME

5

UVST 5 AUX AUDIO, ON = ENABLED

5

FUTURE USE, SET TO ON

USE 4204 RELAY MODULE. REFER TO AAV SECTION OF CONTROL PANEL

6

UVST 6, ON = OUTSIDE, OFF = INSIDE

6

CS CODE LEARN, ON = DISABLED

INSTALLATION AND SETUP GUIDE FOR CONNECTION.

7

UVST 7, ON = OUTSIDE, OFF = INSIDE

7

USER CODE LEARN, ON = DISABLED

NOTE 4: EITHER MUSIC SOURCE OR 4286 VIP MODULE CAN BE USED BUT

8

VOICE TRIGGER, ON = IMMED, OFF = CALLBACK

8

FUTURE USE, SET TO ON

NOT AT THE SAME TIME.

NOTE 5: DO NOT CONNECT IF 4286 VIP MODULE IS USED.

SHIPPED WITH ALL SWITCHES IN "ON" POSITION.

ON

ON

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

SWITCH BANK 1

SWITCH BANK 2

4SPKR 5SPKR 6SPKR 7SPKR AUDAUXILIARYIN AUDAUXILIARYENABLE GND GNDEARTH USEDNOT TIP RING

IN+12VDC

GND

USEDNOT

TRIGVOICERISING

VOICEFALLINGTRIG

NCRELAYVOICE

POLERELAYVOICE

INTRIGALARM

UVSTOUTSIDEPWR

PWRUVSTINSIDE

GND 1MIC 2MIC 3MIC 4MIC 5MIC 6MIC 7MIC PWRUVSTINSIDE GND

1SPKR

2SPKR 3SPKR

ALTERNATE

AUXILIARY

+12 VDC IN FOR

PLUG-IN WALL PACK

(SEE NOTE 2)

																																						AUDIO LEVEL
				1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	ADJUSTMENT
																																						TRIM POT
																																		NOTE 1
													MUSIC SOURCE
												5)	OPTIONAL						AUDIO OUT
													(NOTE 4)
												(OPTIONAL; NOTE
								SELECT APPROPRIATE													GND
				(NOTE 2)	(NOTE 2)				INPUT																													RJ31X	TIP
													CONTROL PANEL																				PLUG							INCOMING
																																						JACK	RING	TELCO
SPKR			PWRUVST	AUX PWR (12VDC)			WAY-2 VOICE TRIGGER (SEE NOTE 3)				BELL OUTPUT																							GRAY	BROWN					LINES
	MIC	GND			GND											SPEAKER					VOLUME																	TIP RING
																						RED	GREEN							DIRECT
																														CONNECT
																															CORD
															INCOMING RING
																INCOMING TIP
															HANDSET RING
																HANDSET TIP
																					SPEAKER
			VOLUME CONTROL DIAL													VOLUME					CONTROL
																TRIM POT
				UVST															4286 VIP												7
																			MODULE												6
																			OPTIONAL
																															5
																			(NOTE 4)
						1																4									4
																						3									3
						2																1 2									2
						3																	P3								1
						4																						KEYED				P7
																						P2						HEADER										ANSWERING
						TYPICAL 1 OF 7																					P1											MACHINE

FOR COMPLETE INFORMATION, SEE 4286 VIP MODULE INSTRUCTIONS.

COMPLIES WITH FCC RULES, PART 68

FCC REGISTRATION NO. AC3 USA-40133-SP-T

RINGER EQUIVALENCE: 1.0B

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO	WARNING: TO PREVENT RISK
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY	OF ELECTRICAL SHOCK,
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE	DISCONNECT TELCO JACK
	BEFORE SERVICING THIS PANEL.
THAT MAY CAUSE UNDESIRED OPERATION.

PREMISES ANSWERING MACHINE AND PHONE (S)

UVCM_UVST-SOC-V1

Figure 3-28: UVS Connections to the Control Panel

Connecting the Transformer

This product uses the 1361 transformer (1361CN in Canada). If you are using X-10 devices, the 1361X10 transformer interface must be used instead of the regular 1361 transformer. The 1361X10 supplies the control panel with AC, and also sends control pulses through the premises electrical system to control the X- 10 devices.

Use 1361CN Transformer in Canadian UL installations.

3-23