J7 CONNECTOR
|
|
|
|
|
|
| 4142TR | |
|
|
|
|
|
|
| CABLE | |
|
|
|
| GROUND START | GRAY (GROUND) | |||
|
| 675 |
|
| ||||
|
|
| TRIGGER |
| YELLOW (OUT 1) | |||
| GROUND | BLUE |
| WHITE (GROUND) | ||||
| START |
| ||||||
|
|
|
| |||||
|
|
|
| RED (OUT 2) | ||||
| MODULE |
|
| TO AUX. POWER | ||||
|
|
|
|
|
|
| ||
|
|
|
| BLACK | GREEN (GROUND) | |||
(CUT ORANGE | TERM. 7 | |||||||
|
|
| ||||||
|
|
|
| |||||
| JUMPER) |
|
| TO AUX. POWER | BROWN (OUT 3) | |||
|
|
|
| VIOLET | BLUE (GROUND) | |||
|
|
|
| TERM. 6 | ||||
BROWN |
| GREEN |
|
|
| (50mA CURRENT DRAW) | BLACK (OUT 4) | |
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||
|
|
|
|
|
| IF USED: |
| |
|
|
|
|
|
| 1. OUT 1 IS NO LONGER |
| |
TO | TO |
|
| USABLE FOR SMOKE DETECTOR RESET | ||||
TELCO | EARTH |
|
| (SEE FIELD 1*46). |
| |||
RING | GROUND | 2. OUT 2, 3, 4 CAN STILL BE |
| |||||
USED TO PROVIDE ALARM STATUS INDICATIONS OR TO OPERATE A KEYSWITCH (SEE FIELD *15).
3. THE 675 IS NOT UL LISTED.
N/U | 1 |
| 2 |
| 3 |
| 4 |
| 5 |
| 6 |
| 7 |
| 8 |
| 9 |
Figure
Installing a Remote Keyswitch
A
The keyswitch is wired across zone 7. This zone is no longer available as a protection zone. Be sure to program Zone 7 with a response type (e.g., type 10).
Operation
•A momentary short across zone 7 arms the partition in the AWAY mode, and a short held for more than 3 seconds arms the partition in STAY mode. A subsequent short disarms the partition.
•The keyswitch LEDs indicate the partition’s status (see table below).
•A momentary short across Zone 7 silences alarm bell and keypad sounds, and disarms the system if it was armed. A subsequent short across Zone 7 clears the alarm memory indication and resets 2- wire smoke and glassbreak detectors (if used).
LED Indications
Green | Red | Indication |
| |
On | Off | Disarmed & Ready |
| |
Off | Off | Disarmed & Not Ready |
| |
Off | On Steady | Armed Away |
| |
Off | Slow Flash | Armed Stay |
| |
Off | Rapid Flash | Alarm Memory |
| |
|
|
|
|
|
Keyswitch Tamper Operation
The tamper switch need not be used for fire or UL Household Burglary installations. For UL Commercial Burglary installations, the tamper switch must be wired to a zone (zone 6 in Figure
Program that zone for Day Trouble/Night Alarm (response type 5). When the keyswitch is removed from the wall, the tamper switch opens, causing an alarm or trouble on the zone. This also causes the control to disable keyswitch operation until the tamper is restored and the associated partition is disarmed.
Wiring for the Remote Keyswitch
To install the 4146 keyswitch, perform the following steps:
Step Action
1Connect the 4146 to the panel as shown in Figure
2If you are using the tamper, make sure it is connected to a zone.
The keyswitch reports as user 0, if Open/Close reporting is enabled in field ✳40.
