Honeywell 3.5 manual Installing the Ground Start Module, Installing the Control, 3-17, Step Action

			SWITCH				4 2 0 4		A D D R E S S			S E T T I N G S
OFF ➞➞ ON			POSITION						("—" means "OFF")
1	ON		➞	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
2		➞	2	ON	—	ON	—	ON	—	ON	—	ON	—	ON	—	ON	—	ON	—
3		➞	3	ON	ON	—	—	ON	ON	—	—	ON	ON	—	—	ON	ON	—	—
4		➞	4	ON	ON	ON	ON	—	—	—	—	ON	ON	ON	ON	—	—	—	—
5		➞	5	ON	ON	ON	ON	ON	ON	ON	ON	—	—	—	—	—	—	—	—

Section 3 - Installing the Control

			SWITCH				4 2 0 4 C F			A D D R E S S			S E T T I N G S
OFF ➞ ➞ ON			POSITION							("—" means "OFF")
1	ON		➞	0	1	2	3	4		5	6	7	8	9	10	11	12	13		14	15
2		➞	2	ON	—	ON	—	ON	—		ON	—	ON	—	ON	—	ON	—		ON	—
3		➞	3	ON	ON	—	—	ON		ON	—	—	ON	ON	—	—	ON	ON		—	—
4		➞	4	ON	ON	ON	ON	—		—	—	—	ON	ON	ON	ON	—	—		—	—
5		➞	5	ON	ON	ON	ON	ON		ON	ON	ON	—	—	—	—	—	—		—	—
																		- ALARM POLARITY
								12						–					SHOWN

4204				RELAY
➞ DIP SWITCH				4
				TYPICAL
FOR SETTING DEVICE ADDRESS				(SHOWN "OFF")
AND ENABLING/DISABLING TAMPER
COVER TAMPER (REED) SWITCH
➞	4-PIN CONSOLE PLUG
				➞
	EITHER OR BOTH
	CAN BE USED			➞
	TB1		➞
13	14	15	16

	12
	11
	10
RELAY	9
3	8
	7
RELAY	6
2	5
	4
RELAY	3
1	2
	1

C

NC

NO

C

NC

NO C NC NO

C

NC

NO

➞ DIP SWITCH

11

NC

NOTIFICATION

- EACH OUTPUT

FOR SETTING DEVICE

APPLIANCE B

PROVIDES

ADDRESS AND

10

NC

2K EOLR

STYLE Y

ENABLING/DISABLING

+

#610-7

SUPERVISION

9

TAMPER

- EACH OUTPUT

COVER TAMPER (REED) SWITCH

8

NC

POLARIZED

RATED 1.2A MAX

NC

NOTIFICATION

- USE

➞

6 7

APPLIANCE

NOTIFICATION

4-PIN CONSOLE PLUG

–

APPLIANCES

➞

NOTIFICATION

COMPATIBLE

5

APPLIANCE A

WITH

EITHER OR BOTH

4

2K EOLR

NOTIFICATION

CAN BE USED

➞

+

#610-7

APPLIANCE

3

POWER SUPPLY

TB1

➞

2

NC

VOLTAGE

1

+

POWER FOR

RATING

13

14 15 16

NC

–

} NOTIFICATION APPLIANCE A,

▲

NOTIFICATION APPLIANCE B

YEL

DATA IN

TB2

8-28VDC OR VFW. UP TO 2.4A

FROM CONTROL

DEPENDING ON BELL CURRENT

YEL	DATA IN	▲	TB2
BLK	FROM CONTROL
	(–) GROUND
GRN
	DATA OUT
RED	TO CONTROL
	(+) 12V

Figure 3-21: 4204 Relay Module

Installing X10 Devices

X-10 devices are either plugged into standard AC outlets or wired into the AC electrical system by a licensed electrician, depending on the type of device used.

Note each device’s House and Unit Code setup, as these codes will be used to program the devices in Output Programming in #93 Menu Mode described in the Programming Guide.

BLK	(–) GROUND	NOTIFICATION APPLIANCE AND
GRN	DATA OUT	CONSOLE DATA OUTPUTS ARE
		POWER LIMITED
RED	TO CONTROL
	(+) 12V; SUPPLIES POWER TO MODULE
	CIRCUITRY (INCLUDING NOTIFICATION
	APPLIANCE RELAY COILS). CURRENT
	DRAIN AT 12V IS: 25 mA + (80 mA PER
	ACTIVE OUTPUT)

Figure 3-22: 4204CF Relay Module

X-10 devices require the use of a 1361X10 transformer in place of the regular 1361 transformer.

X-10 devices respond to “on” and “off” commands sent from the panel through the 1361X10 transformer.

To connect the 1361X10 transformer, see Connecting the Transformer, later in this section.

Installing the Ground Start Module

UL	The Ground Start Module is not intended for
	use in UL Listed applications.

Output 1 may be used to trigger an optional 675 Ground Start Module for installations having telephone lines that require ground start instead of loop start operation to obtain a dial tone from the telco central office.

When the panel has a message to transmit to the central station, it seizes the line, goes off hook, and then triggers the 675 Module to connect the RING side of the telephone line to earth ground. The panel causes the module to break the connection between RING and earth ground when it obtains a dial tone.

To install the 675 Ground Start Module, perform the following steps:

Step Action

1Determine which side of the telephone line is the RING side by connecting the (+) lead of a DC voltmeter to earth ground, and the (-) lead to one side of the telephone line.

The wire that reads + 50VDC is the RING side.

2Connect the 675 Ground Start Module to the panel’s J7 connector trigger output 1, to auxiliary power, and to the RING side of the telephone line as shown in Figure 3-23.

3Program field 1✳46 Auxiliary Output Enable with a [0].

You cannot use Output 1 for the Ground Start if you are using it for Open/Close or an AAV module.

3-17