Connecting Vacuum Pumps | Sterling 882.00255.00 CV3-655 guide

Connecting Vacuum Pumps and Filter Chambers to the Network

Connecting Vacuum Pumps

Make sure that all previous installation steps have been done first before starting this task.. To connect a vacuum pump to the network:

1.Attach patchcords from vacuum pump junction boxes to the appropriate ArmorBlock connectors. See Figures 12, 13, and 14.

Figure 12: 4-Vacuum Pump ArmorBlock Connections

Note 1: The block shown is addressed 33, for the first (2) pumps. The block addressed 34 would have connectors for pumps 3 and 4, etc.

Note 2: If a pump does not have “Pump Fault #2” or a local pump alarm light, the T connector is not required. Connect the patchcord directly to the connector on the ArmorBlock.

24-Pump, 128-Station Controller

Chapter 3: Installation

28

Image 29

Sterling 882.00255.00 CV3-655 specifications Connecting Vacuum Pumps and Filter Chambers to the Network

Contents

SCC 24-Pump 128-Station Controller Parts and Service Department Shipping Information Table of Contents Maintenance Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Operator Responsibility ResponsibilityGeneral Responsibility Reporting a Safety Defect Maintenance Responsibility Mechanical Features Standard FeaturesFunctional Description Models Covered in This Manual Safety Devices and Interlocks Optional FeaturesElectrical Features Controller Features Fail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs System Installation Overview InstallationUncrating Mounting the Control Panel Installing KwikLink Cable Making Control Panel Power Drop Wiring ConnectionsElectrical Connections Running KwikLink Cables Setting Up Mounting Plates Setting Up and Installing Mounting Plates Terminating Cable Runs Installing Assembled Mounting Plates Discard the standard resistor cap to eliminate confusion Installing Inside KwikLink Connectors with Blank Caps ArmorBlock Address Ranges Addressing and Installing ArmorBlocksAddressing ArmorBlocks Setting ArmorBlock Addresses Using seal block to pierce cable Installing KwikLink Connectors Connecting the Remote Interface to the Main Controller Connecting the Controller to the NetworkPage Proper Controller and Remote Interface Connections Connecting the Power Supply Enclosure to the NetworkPage Connecting Vacuum Receivers to the Network Proper Power Supply Enclosure Connections 24/128 8-Connector ArmorBlock Connections Proper Vacuum Receiver Connections Connecting Vacuum Pumps Connecting Vacuum Pumps and Filter Chambers to the Network Proper Vacuum Pump Connections, Standard XPD/XPC Pumps Proper Vacuum Pump Connections, Xpdb Pump Connecting Filter Chambers Proper Filter Chamber Connections, Blowback Proper Filter Chamber Connections, Implosion Type Connecting Central Alarms to the Network Proper Central Alarm Connections Connector ArmorBlock Connections for Central Alarms Setup Setting the Number of Stations and the Number of Pumps Setting Up the System Naming Purge Valves and Materials Setting the Date/TimeChecking Addressing and Wiring for System Components Setting Up Alarm Silences Setting Up Pump Staging Alarm Horn Silence Setting Up a Single Station Setting Up Stations Naming Stations To copy the selected station’s settings to one other station Copying Settings from One Station to Others Setting Up a Single Pump Setting Up PumpsPage Naming Pumps Copying Settings from One Pump to Others To copy the current pump’s settings to all other pumps To copy the selected pump’s settings to one other pump Finishing Setup Setting Up Passwords Save/Restore Settings Password Duration Initial Startup Starting and Stopping the System OperationOverview Reviewing Station Status Basic Tasks Color Label Description Reviewing Pump Status Logging On and Logging Off Enabling and Disabling Stations and Pumps Enter the alphanumeric password Navigating among the Station Operator Screens Reviewing and Adjusting Basic Station SettingsReaching and Reading the Station Operator Screens Activating and Stopping Priority Convey for a Station Adjusting Convey Time and Dump Delay Changing the Mixture for a Remote Proportioning Valve Transferring Stations to a Standby Pump Reviewing and Resetting a Pump Hour MeterAdvanced Tasks Page Page Silencing Alarms AlarmsReviewing Alarms Preventative Maintenance MaintenanceCorrective Maintenance Network Scanner Module Considerations Memory Module Considerations Configurable SettingsOptions for Station Setup Name Description Options Default Conveying Options Option Input Pump, 128-Station Controller Configurable Settings Pump, 128-Station Controller Configurable Settings Options for Pump Setup Pump, 128-Station Controller Configurable Settings General Troubleshooting Troubleshooting Alarm message Possible cause Station Alarms Pump, 128-Station Controller Troubleshooting System Alarms Pump Alarms Optional Components WarrantyAppendix 24-Pump, 128-Station Controller with 10 Display Drawings and Diagrams Typical System Installation Layout Spare Parts List Credit Returns Warranty ReturnsReturned Material Policy Controller Identification Serial Number Tag Safety Tag InformationController Safety Tags Technical Assistance Contact Information Service DepartmentParts Department Sales Department