Create your ﬁrst port and install the driver | Tektronix Phaser 840

Windows 95 and Windows 98: PhaserPort Software 6

Create your ﬁrst port and install the driver

1.After the port monitor is installed, the Add PhaserPort dialog box is displayed. Create your ﬁrst port:

a.In the Description ﬁeld, enter a name for the port (this can be the printer name/model, location, or any other descriptive name of your choice), such as Phaser 840.

b.In the Name/Address ﬁeld, enter the IP address or DNS name of the printer (for example, 192.1.1.2).

If you don’t know the printer’s IP address or DNS name, click Browse to display a list of printers on the network. Double-click the printer you want; PhaserPort automatically enters the information into the Add PhaserPort dialog. To search the network again, click Refresh; to narrow down the search by using subnets, click Advanced.

c.Click OK.

2.If you have NetWare software installed on your computer, you are asked if you want to install the PhaserShare Administrator software. If you also want to print using NetWare, choose Yes, then click Next.

3.If you chose to install drivers and PPD ﬁles earlier in the installation, the Finish Installation dialog displays information about the Add Printer Wizard. Read the information, then click Next to start the Add Printer Wizard, which allows you to install the driver for your printer. The drivers are on your printer’s CD-ROM.

If you did not choose to install drivers and PPD ﬁles earlier in the installation, go to Step 5.

4.Install the driver.

a.In the Add Printer Wizard, click Next. Choose Local printer, then click Next.

b.Click Have Disk, type the drive letter for the CD-ROM, and click OK.

c.Select your printer from the list, then click Next.

d.In the Available ports list, select the port you created during the ﬁrst part of the installation and click Next.

Setup Guide

33

Image 39

Tektronix Phaser 840 setup guide Create your ﬁrst port and install the driver

Contents

L O R P R I N T E R Page Phaser 840 Color Printer PhaserShare Networking Setup Guide Page Contents Index Setting the Printer’s IP Addressing ParametersPhaserLink Printer Management Software Windows NT Unix Introduction Before you begin network conﬁguration Printing a ConﬁgurationPrinting a Conﬁguration Printer management If you need more information PhaserShare Series B Ethernet interface Connecting Your Printer to a Network Built-in Ethernet connector Ethernet connections and indicators PhaserShare Series B Ethernet card 10Base5 Thick Ethernet Ethernet cables and termination10BaseT or 100BaseTx Twisted Pair 10Base2 Thin Ethernet PhaserShare Series B Token Ring card Token Ring connections and indicators Ring speed jumper Token Ring parameters Token Ring conﬁguration Conﬁguring Token Ring parameters Using the conﬁg-TokenRingscript Arp Using PhaserLink software to conﬁgure Token Ring Using the PhaserShare Administrator to conﬁgure Token Ring PhaserShare Series B LocalTalk card LocalTalk card connections and indicatorsLocalTalk connection Connecting to a single computer LocalTalk connectors, cables, and terminators Connecting Your Printer to a Network PhaserShare Networking Conﬁguration overview EtherTalk, LocalTalk TokenTalk Configuration Finding the printer’s name in the Chooser Novell NetWare Configuration Installing the PhaserShare AdministratorInstallation Select a print server Using the Quick Conﬁguration WizardStart the PhaserShare Administrator Log on to the ﬁle server Launch the Quick Conﬁguration Wizard Conﬁgure the printer and set up queues Verify information and ﬁnish the conﬁguration Setting IPX frame types from the front panel TCP/IP Configuration Unix Adding the printer to the host tableAssigning a print queue to the printer Assigning print queues with PhaserPrint for Unix Required remote printer queue namesUnix model ﬁles Example installation for a typical BSD Unix system Descriptions of printcap parameters Sample printcap ﬁle Printer conﬁguration Listing the contents of unix.tar Extracting ﬁles from unix.tarExtracting the ﬁles TCP/IP conﬁguration for a PC Windows 95 PhaserPort Software Setting the printer’s IP address PhaserPort software installationUsing the installer Create your ﬁrst port and install the driver Adding a port for a new printer Installation Completed dialog, click Finish Adding a port to an existing printer Changing a port’s IP address Windows NT Add the printer Click Start, Settings, and Printers Creating an AppleTalk port Creating an LPR port Install the driver Name the printer and set up sharingWindows NT creates the printer Adding a Windows NT 4.0 driver on an NT 3.51 server Select the port where the printer is connected Enter the printer’s name and set up sharing Adding a Windows NT 3.x driver Creating an LPR port Set up sharing Windows NT PhaserShare Networking Setting the Printer’s IP Addressing Parameters Setting the Printer’s IP Addressing Parameters Setting IP parameters from the front panel Set the network mask Setting IP parameters Rarp or Bootp T E Setting IP parameters Dhcp Installing the Dhcp serverSetting up a Dhcp server Open the Network Administration group Dhcp transactions Supported BOOTP/DHCP ﬁelds Setting IP parameters PostScript utility ﬁle Unix only Conﬁg-IP ﬁlename Running the conﬁg-IPscript Setting IP parameters PhaserLink Printer Management Software DNS Setting the Printer’s IP Addressing Parameters Accessing printer information from a browser PhaserLink Printer Management Software PhaserLink Printer Management software help ﬁles Conﬁguring PhaserLink HelpAccessing PhaserLink Help Information Forwarding Setting printer parameters PhaserLink software pages Disabling Information Forwarding Index With config-IP script With config-TokenRingscript Rarp Page Printed on recycled paper