Index | Tektronix Phaser 840 guide

Index

A

Adapter Status 12

ARP (Address Resolution Protocol)

with config-IP script 55

with config-TokenRing script 13

B

BOOTP 47

Broadcast 12

Broadcast address 48

C

cables 8 Chooser 20 conﬁg-IP55 conﬁg-TokenRing14 Conﬁguration Page

front panel 2

D

DHCP 51 DNS

printer configuration 57 UNIX host configuration 25

DOS 1

E

Early Token Release 12 etc/hosts ﬁle 27 etc/printcap ﬁle 28 Ethernet

adapters 5 cables 8 terminators 8

EtherTalk 19

F

front panel

printing Configuration Page 2 setting IPX frame type 24

setting printer’s IP addressing parameters 48

G

Gateway IP address 48

H

hosts ﬁle 27

I

information forwarding 61 installation

PhaserShare software 21 Intelligent Ready 3

IP addressing parameters DHCP 51

setting from the front panel 48

setting using a PostScript utility file (UNIX) 54 setting using PhaserLink software 56 setting using RARP or BOOTP 49

J

Job accounting 3

L

LocalTalk 19

M

model ﬁles 26

N

NetWare 21

Network Address 12

Network mask 48

NIS 25

Setup Guide

63

Image 69

Tektronix Phaser 840 setup guide Index, With config-IP script With config-TokenRingscript

Contents

L O R P R I N T E R Page Phaser 840 Color Printer PhaserShare Networking Setup Guide Page Contents PhaserLink Printer Management Software Setting the Printer’s IP Addressing ParametersWindows NT Index Unix Introduction Before you begin network conﬁguration Printing a ConﬁgurationPrinting a Conﬁguration Printer management If you need more information PhaserShare Series B Ethernet interface Connecting Your Printer to a Network Built-in Ethernet connector Ethernet connections and indicators PhaserShare Series B Ethernet card 10BaseT or 100BaseTx Twisted Pair Ethernet cables and termination10Base2 Thin Ethernet 10Base5 Thick Ethernet PhaserShare Series B Token Ring card Token Ring connections and indicators Ring speed jumper Token Ring parameters Token Ring conﬁguration Conﬁguring Token Ring parameters Using the conﬁg-TokenRingscript Arp Using PhaserLink software to conﬁgure Token Ring Using the PhaserShare Administrator to conﬁgure Token Ring PhaserShare Series B LocalTalk card LocalTalk card connections and indicatorsLocalTalk connection Connecting to a single computer LocalTalk connectors, cables, and terminators Connecting Your Printer to a Network PhaserShare Networking Conﬁguration overview EtherTalk, LocalTalk TokenTalk Configuration Finding the printer’s name in the Chooser Novell NetWare Configuration Installing the PhaserShare AdministratorInstallation Start the PhaserShare Administrator Using the Quick Conﬁguration WizardLog on to the ﬁle server Select a print server Launch the Quick Conﬁguration Wizard Conﬁgure the printer and set up queues Verify information and ﬁnish the conﬁguration Setting IPX frame types from the front panel TCP/IP Configuration Unix Adding the printer to the host tableAssigning a print queue to the printer Assigning print queues with PhaserPrint for Unix Required remote printer queue namesUnix model ﬁles Example installation for a typical BSD Unix system Descriptions of printcap parameters Sample printcap ﬁle Printer conﬁguration Listing the contents of unix.tar Extracting ﬁles from unix.tarExtracting the ﬁles TCP/IP conﬁguration for a PC Windows 95 PhaserPort Software Setting the printer’s IP address PhaserPort software installationUsing the installer Create your ﬁrst port and install the driver Adding a port for a new printer Installation Completed dialog, click Finish Adding a port to an existing printer Changing a port’s IP address Windows NT Add the printer Click Start, Settings, and Printers Creating an AppleTalk port Creating an LPR port Install the driver Name the printer and set up sharingWindows NT creates the printer Adding a Windows NT 4.0 driver on an NT 3.51 server Select the port where the printer is connected Enter the printer’s name and set up sharing Adding a Windows NT 3.x driver Creating an LPR port Set up sharing Windows NT PhaserShare Networking Setting the Printer’s IP Addressing Parameters Setting the Printer’s IP Addressing Parameters Setting IP parameters from the front panel Set the network mask Setting IP parameters Rarp or Bootp T E Setting IP parameters Dhcp Installing the Dhcp serverSetting up a Dhcp server Open the Network Administration group Dhcp transactions Supported BOOTP/DHCP ﬁelds Setting IP parameters PostScript utility ﬁle Unix only Conﬁg-IP ﬁlename Running the conﬁg-IPscript Setting IP parameters PhaserLink Printer Management Software DNS Setting the Printer’s IP Addressing Parameters Accessing printer information from a browser PhaserLink Printer Management Software PhaserLink Printer Management software help ﬁles Conﬁguring PhaserLink HelpAccessing PhaserLink Help Information Forwarding Setting printer parameters PhaserLink software pages Disabling Information Forwarding Index With config-IP script With config-TokenRingscript Rarp Page Printed on recycled paper