Troubleshooting
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
No picture. | The output and input for the picture are | Set “VIDEO CONV.” to “ON” or connect your source | ||
| connected to different types of video | components in the same way as you connect your |
| |
| jacks. | video monitor to this unit. |
| |
|
|
|
| |
| Connect your video monitor to the COMPONENT | |||
| only output at the COMPONENT VIDEO | VIDEO MONITOR jacks. |
| |
| MONITOR OUT jacks. |
|
| |
|
|
|
| |
| Connect your video monitor to the HDMI OUT or | — | ||
| video signals cannot be output at the S | COMPONENT VIDEO MONITOR OUT jacks. |
| |
| VIDEO and VIDEO MONITOR OUT |
|
| |
| jacks. |
|
| |
|
|
|
| |
| This unit outputs the video signals are not | Select “INITIALIZE” in “VIDEO” to reset the video | ||
| supported on the video monitor connected | parameters. |
| |
| to the HDMI OUT jack. |
|
| |
| Set “MONITOR CHECK” to “YES”. | |||
|
| |||
|
|
|
| |
| Pure Direct mode is active. | Turn off the Pure Direct mode. | ||
|
|
|
| |
|
| Set “MODE” in “PURE DIRECT” to | ||
|
| “AUDIO+VIDEO”. |
| |
|
|
|
| |
|
|
| ||
|
|
|
| |
Short message | “SHORT MESSAGE” is set to “OFF”. | Set “SHORT MESSAGE” to “ON”. | ||
displays do not |
|
|
| |
“GRAY BACK” is set to “OFF”. | Set “GRAY BACK” to “AUTO”. | |||
appear on the video | ||||
monitor. |
|
|
| |
“VIDEO CONV.” is set to “OFF”. | Set “VIDEO CONV.” to “ON”. | |||
| ||||
|
|
|
| |
| The signals input at the HDMI input jacks |
|
| |
| are being output at the HDMI OUT jack. |
|
| |
|
|
|
| |
| Video signals in the progressive format or |
|
| |
| HDTV video signals are being input. |
|
| |
|
|
|
| |
The sound suddenly | The protection circuitry has been activated | Check that the speaker impedance setting is correct. | ||
goes off. | because of a short circuit, etc. |
|
| |
Check that the speaker wires are not touching each | — | |||
|
| |||
|
| other and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned off this unit. | Turn on this unit, and play the source again. | — | |
|
|
|
| |
Sound is heard from | Incorrect cable connections. | Connect the cables properly. If the problem persists, | ||
the speaker on one |
| the cables may be defective. |
| |
side only. |
|
|
| |
The speaker level settings are incorrect. | Adjust “LEVEL” settings. | |||
| ||||
|
|
|
| |
Only the center | When playing a monaural source with a |
|
| |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
| |
No sound is heard | “CENTER SP” in “CONFIG” is set to | Set “CENTER SP” to “SMALL” or “LARGE”. | ||
from the center | “NONE”. |
|
| |
speaker. |
|
|
| |
|
|
|
| |
No sound is heard | This unit is in the “STRAIGHT” mode. | Press OSTRAIGHT to turn off the “STRAIGHT” | ||
from the presence |
| mode. |
| |
speakers. |
|
|
| |
You are using a source or program | Try another sound field program. | |||
|
combination that does not output sound from all channels.
INFORMATION | ADDITIONAL |
|
|
English