Troubleshooting

Problem

Cause

Remedy

See

page

 

 

 

An audio source

The audio source component is not

Connect the audio source component to the DIGITAL

21

cannot be recorded by

connected to the DIGITAL INPUT jacks.

INPUT jacks.

 

the digital recording

 

 

 

Some components cannot records Dolby

 

 

component connected

 

 

to the DIGITAL

Digital or DTS sources.

 

 

OUTPUT jacks.

You are trying to record an audio source

Connect the recording component to the analog

21

 

 

input at the DOCK terminal by the digital

AUDIO OUT (DVR, VCR or MD/CD-R) jacks.

 

 

recording component connected to the

 

 

 

DIGITAL OUTPUT jacks.

 

 

 

 

 

 

 

(U.S.A. model only)

Connect the recording component to the analog

21

 

HD Radio signals are not output at the

AUDIO OUT (DVR, VCR or MD/CD-R) jacks.

 

 

DIGITAL OUTPUT jacks

 

 

 

 

 

 

An audio source

The audio source component is not

Connect the audio source component to the AUDIO

21

cannot be recorded by

connected to the analog AUDIO IN jacks.

IN jacks.

 

the analog recording

 

 

 

XM Satellite Radio and SIRIUS Satellite

 

 

component connected

 

 

to the analog AUDIO

Radio signals are not output at the analog

 

 

OUT (DVR, VCR or MD/

AUDIO OUT (DVR, VCR or MD/CD-R)

 

 

CD-R) jacks.

jacks.

 

 

 

 

 

 

Recorded materials

The settings made on this unit (such as

 

 

sound differently.

tonal quality, volume level and sound field

 

 

 

programs) do not affect recorded material.

 

 

 

 

 

 

A video source cannot

"VIDEO CONV." is set to "ON".

While "VIDEO CONV." is set to "ON", video signals

21, 80

be recorded by the

 

are output only at the MONITOR OUT jacks. To

 

recording component.

 

record a video source by the recording component, set

 

 

 

"VIDEO CONV." to "OFF" and make the same type

 

 

 

of video connections between each component (e.g.

 

 

 

VCR IN (S VIDEO) to DVR OUT (S VIDEO).

 

 

 

 

 

The sound field

“MEMORY GUARD” in “SET MENU”

Set “MEMORY GUARD” to “OFF”.

84

parameters and some

is set to “ON”.

 

 

other settings of this

 

 

 

unit cannot be

 

 

 

changed.

 

 

 

 

 

 

 

This unit does not

The internal microcomputer has been

Disconnect the power cable from the AC wall outlet

—

operate properly.

frozen by an external electric shock (such

and then plug it in again after about 30 seconds.

 

 

as lightning or excessive static electricity)

 

 

 

or by a power supply with low voltage.

 

 

 

 

 

 

“CHECK SP WIRES”

Speaker cables are short-circuited.

Make sure all speaker cables are connected correctly.

13

appears in the front

 

 

 

panel display.

 

 

 

 

 

 

 

There is noise

This unit is too close to the digital or high-

Move this unit further away from such equipment.

—

interference from

frequency equipment.

 

 

digital or radio

 

 

 

frequency equipment.

 

 

 

 

 

 

 

The picture is

The video source uses scrambled or

 

 

disturbed.

encoded signals to prevent dubbing.

 

 

 

 

 

 

This unit suddenly

The internal temperature becomes too

Wait about 1 hour for this unit to cool down and then

—

enters the standby

high and the overheat protection circuitry

turn it back on.

 

mode.

has been activated.

 

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

English

107 En