Simplicity H924RX How To Adjust The Belts, How To Replace The Belts, How To Adjust The Belt Guide

Page 13

11.(Figure 15) To check the adjustment, depress the drive lever and check the length “A” of the drive spring (7). In correct adjustment, the length “A” of the drive spring (7) is as follows:

minimum 3 inches (76 mm) maximum 3-3/8 inches (85 mm).

12.(Figure 23) Install the bottom panel (2).

13.Tighten the bolts (3) on each side of the bottom panel (2).

How To Adjust The Belts

The belts will stretch during normal use. If you need to adjust the belts due to wear or stretch, proceed as follows.

How To Adjust The Auger Drive Belt

If the snow thrower will not discharge snow, check the adjustment of the auger drive cable. See “How To Check And Adjust The Cables” in the Maintenance section. If the adjustment is correct, then check the condition of the auger drive belt. If the auger drive belt is damaged, replace the auger drive belt. See “How To Replace The Belts” in the Maintenance section. If the auger drive belt is loose, adjust as follows.

1.(Figure 1) Pull out the safety key (8).

2.(Figure 18) Remove screw (2) from belt cover (1). Remove the belt cover (1).

3.(Figure 19) Loosen the nut (2) on the idler pulley (3) Move the idler pulley (3) 1/8 inch (3 mm) toward the auger drive belt (4).

4.Tighten the nut (2).

5.(Figure 22) Depress the auger drive lever. Check the tension on the auger drive belt

(4). In correct adjustment, the auger drive belt (4) will deflect 1/2 inch (12.5 mm) (5) with moderate pressure. If the adjustment is not correct, repeat the adjustment.

6.(Figure 18) Install the belt cover (1). Tighten screw (2).

7.Check the adjustment of the auger drive cable. See “How To Check And Adjust The Cables” in the Maintenance section.

Traction Drive Belt

The traction drive belt has constant spring pressure and does not require an adjustment. If the traction drive belt is slipping, replace the belt. See “How To Replace The Belts” in the Maintenance section.

How To Replace The Belts

The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center.

Some steps require the assistance of a second person.

How To Remove the Auger Drive Belt

If the auger drive belt is damaged, the snow thrower will not discharge snow. Replace the damaged belt as follows.

1.(Figure 1) Pull out the safety key (8).

2.(Figure 23) Loosen the bolts (3) on each side of the bottom panel (2).

1742227

3.Remove the bottom panel (2).

4.(Figure 18) Remove screw (2) from belt cover (1). Remove the belt cover (1).

5.(Figure 19) Loosen the belt guide (9). Pull the belt guide (9) away from the auger drive pulley (10).

6.Pull the idler pulley (3) away from the auger drive belt (4) and slip the auger drive belt

(4) off of the idler pulley (3).

7.Remove the auger drive belt (4) from the engine pulley (11). To remove the auger drive belt (4), the engine pulley (11) may have to be partially rotated.

8.(Figure 20) Remove the top four bolts (21) that hold together the auger housing (22) and the motor box (23). Loosen the bottom two bolts (24). The auger housing (22) and the motor box (23) can now be split apart for removal of the belt.

9.(Figure 19) Remove the old auger drive belt (4) from the auger drive pulley (10). Replace the auger drive belt (4) with an original factory replacement belt available from an authorized service center.

10.Install the new auger drive belt (4) onto the auger drive pulley (10).

11.Assemble the auger housing (22) to the motor box (23) with the four bolts (21) that were removed in step 8. Tighten the bottom two bolts (24).

12.Install the auger drive belt (4) onto the engine pulley (11).

13.Slip the auger drive belt (4) under the idler pulley (3).

14.Adjust the auger drive belt (4). See “How To Adjust The Auger Drive Belt” in the Maintenance section.

15.Adjust the belt guide (9). See “How To Adjust The Belt Guide” in the Maintenance section.

16.(Figure 18) Install the belt cover (1). Tighten screw (2).

17.Check the adjustment of the cables. See “How To Check And Adjust The Cables” in the Maintenance section.

How To Remove the Traction Drive Belt

If the snow thrower will not move forward, check the traction drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows.

1.(Figure 1) Pull out the safety key (8).

2.Remove the auger drive belt. See “How To Remove The Auger Drive Belt” in the Maintenance section.

3.(Figure 19) Remove the e−ring (17) from one end of the swing plate axle rod (18). Remove the swing plate axle rod (18) to allow the the swing plate to pivot forward.

4.Remove the traction drive spring (16).

5.Remove the old traction drive belt (13) from the traction drive pulley (14) and from the engine pulley (15). Replace the traction drive belt (13) with an original factory replacement belt available from an authorized service center.

6.Install the new traction drive belt (13) onto the traction drive pulley (14) and onto engine pulley (15).

13

en

7.Make sure the traction drive idler pulley

(12)is properly aligned with the traction drive belt (13).

8.Attach the traction drive spring (16).

9.Install the swing plate axle rod (18) and secure with the e−ring (17) removed earlier.

10.(Figure 31) The bottom of the swing plate

(20)must be positioned between the alignment tabs (19). Make sure the swing plate (20) is properly secured.

NOTE: If the drive will not engage after the traction drive belt has been replaced, then check to make sure that the swing plate is positioned between the alignment tabs (19).

11.(Figure 19) Install and adjust the auger drive belt (4). See “How To Remove The Auger Drive Belt” in the Maintenance section.

12.Adjust the belt guide (9). See “How To Adjust The Belt Guide” in the Maintenance section.

13.(Figure 23) Install the bottom panel (2).

14.Tighten the bolts (3) on each side of the bottom panel (2).

15.(Figure 18) Install the belt cover (1). Tighten screw (2).

16.Check the adjustment of the cables. See “How To Check And Adjust The Cables” in the Maintenance section.

How To Adjust The Belt Guide

1.(Figure 1) Pull out the safety key (8).

2.(Figure 18) Remove screw (2). Remove the belt cover (1).

3.(Figure 1) Engage the auger drive lever (5).

4.(Figure 24) Measure the distance between the belt guide (2) and auger drive belt (3). The correct distance (4) is 1/8 inch (3 mm).

5.If an adjustment is necessary, loosen the mounting bolt for the belt guide (2). Move the belt guide (2) to the correct position

(4). Tighten the mounting bolt for the belt guide (2).

6.(Figure 18) Install the belt cover (1). Tighten screw (2).

How To Adjust Or Replace The Friction Wheel

How To Check The Friction Wheel

If the snow thrower will not move forward, check the traction drive belt, the traction drive cable or the friction wheel. If the friction wheel is worn or damaged, it must be replaced. See “How To Replace the Friction Wheel” in this section. If the friction wheel is not worn or damaged, check as follows.

1.(Figure 1) Remove the gas from the gas tank. Stand the snow thrower up on the front end of the auger housing (4).

WARNING: Drain the gasoline outdoors, away from fire or flame.

2.Pull out the safety key (8).

3.(Figure 23) Loosen the bolts (3) on each side of the bottom panel (2).

4.Remove the bottom panel (2).

5.(Figure 1) Position the shift speed lever (6) in the lowest forward speed.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents OPERATOR’S Manual 1742227 Contents Left Right Down 1742227 When Adding Fuel Training Rules for Safe OperationPreparation OperationChildren Service, Maintenance And Storage Ignition SystemClearing a Clogged Discharge Chute EmissionsOperation AssemblyHow To Throw Snow Figure How To Stop The Snow ThrowerHow To Use The Wheel Lockout Pin How To Stop The Engine FigureMaintenance Maintenance ChartHow To Adjust The Scraper Bar Figure How To Adjust The Height Of The Skids FigureHow To Check And Adjust The Cables Lubrication Every 10 Hours FigureHow To Replace The Belts How To Adjust The BeltsHow To Adjust The Belt Guide How To Adjust Or Replace The Friction WheelHow To Prepare The Snow Thrower For Storage How To Replace the Auger Shear BoltHow To Order Replacement Parts Trouble Shooting Chart Significations Table DES MatièresGauche Droit Haut BAS Avertissement Avertissement Formation Règles D’UTILISATION Dans DES Conditions DE SécuritéPréparation Enfants Entretien, maintenance et stockageNettoyage d’une chute encrassée Système d’allumageFonctionnement MontageSe familiariser avec le chasse−neige Figure Commande du déversement de la neigeArrêt du chasse−neige Figure Avancer et reculer FigureOu un levier pour retirer neige et débris Conseils pour l’utilisation du chasse−neigeEntretien Tableau DE MaintenanceRéglage de la hauteur des patins Figure Pièces à ne pas lubrifier FigureRéglage du bord d’attaque Figure Vérification et réglage des câblesRéglage ou remplacement du disque de friction Remplacement des courroiesRéglage du guide de courroie Taille du pneu Distance « a » Préparation du chasse−neige pour le remisage12 et 13 pouces 10,5 cm 4−1/8 Pouces Sur la plus basse vitesse de la marche avantTableau DE Depannage Commande de pièces détachéesInhalt Montage Betrieb Wartungsdiagramm FehlersuchdiagrammLinks Rechts Oben Nach Unten Gefahr Warnung Übung Regeln FÜR DEN Sicheren BetriebVorbereitung Kinder Service, Wartung und LagerungFreiräumen eines verstopften Auswurfkanal AbgaseBetrieb Kontrollieren des Schneeauswurfs Über die Schneefräse AbbAnhalten der Schneefräse Abb Vorwärts- und Rückwärtsfahren AbbTips für das Schneefräsen Schnee und Geröll vom Räumwerk entfernenWartung WartungsdiagrammEinstellung der Kufenhöhe Abb Objekte, die nicht geschmiert werden AbbEinstellung der Streichstange Abb Überprüfen und Einstellen der KabelEinstellung der Riemenführung Auswechseln der RiemenEinstellen bzw. Auswechseln des Reibrads Vorbereitung der Schneefräse auf die Lagerung Auswechseln des SchneckenscherbolzensBestellen von Ersatzteilen Fehlersuchdiagramm Montaggio USO Tabella DI Manutenzione Indice1742227 Pericolo Avvertenza Addestramento Regole PER UN Funzionamento SicuroPreparazione ConduzionePulizia di uno scarico a gravità ostruito BambiniManutenzione, assistenza e conservazione EmissioniUSO MontaggioLancio di neve Figura Interruzione delle operazioni dello spazzaneve FiguraPrima di accendere il motore Spegnimento del motore FiguraAvviamento di un motore caldo Figura Suggerimenti per spazzare la neveSe possibile, scaricare la neve sottovento Manutenzione Tabella DI ManutenzioneRegolazione della barra raschiatrice Figura Parti che non devono essere lubrificate FiguraControllo e regolazione dei cavi Regolazione delle cinghieRimozione della cinghia di azionamento della trivella Sostituzione delle cinghieRegolazione della guida della cinghia Regolazione o sostituzione della ruota di frizionePreparazione dello spazzaneve per il rimessaggio Sostituzione dei bulloni di sicurezza della trivellaOrdinazione di parti di ricambio Tabella PER LA Soluzione DEI Problemi Koble til elektrisitetsledning Innhold1742227 Fare 1742227 Opplæring Regler for Sikker BrukForberedelse BrukBarn Service, vedlikehold og lagringRengjøre en tilstoppet utkastingssjakt UtslippBruk MonteringHvordan frese snø Figur Hvordan stoppe snøfreseren FigurFør du starter motoren Hvordan stanse motoren FigurHvordan fjerne snø eller rester fra naverhuset VedlikeholdstabellSnøfresingstips Vedlikehold Hvordan skifte ut beltene Hvordan justere belteneHvordan justere beltelederen Hvordan skifte ut sikkerhetsbolt i naver Hvordan justere eller skifte ut friksjonshjuletHvordan gjøre snøfreseren klar for lagring Hvordan bestille reservedelerFeilsøkingstabell Innehåll Varningssymboler OCH Förklaringar1742227 Fara Varning Utbildning Regler FÖR Säkert HandhavandeDrift FörberedelseRengöring av ett igensatt utkaströr Service, underhåll och förvaringUtsläpp TändningssystemAnvändning Hur man slungar snö Figur Hur man gör för att köra framåt och bakåt FigurHur man använder hjulspärrpinne Figur Innan motorn startasHur man tar bort snö och skräp ur inmatarhuset UnderhållsschemaSnöröjningstips Underhåll Hur man byter ut remmarna Hur man justerar remmarnaHur man justerar remguiden Hur man byter brytbult till inmataren Hur man justerar eller byter ut friktionshjuletHur man förbereder snöslungan för förvaring Hur man beställer reservdelarFelsökningsschema 1742227 1742227 1742227 1742227 1742227 1742227 1742227 1742227 1742227

H924RX specifications

The Simplicity H924RX is a standout addition to the world of residential zero-turn mowers, blending cutting-edge technology with exceptional performance. Designed for homeowners who demand both efficiency and ease of use, this mower comes equipped with features that facilitate an enjoyable mowing experience while delivering superior results.

At the heart of the H924RX is its robust engine, which provides reliable power for tackling thick grass and uneven terrains. The mower is equipped with a high-performance, air-cooled Kawasaki engine, known for its durability and efficiency, ensuring that you can maintain your lawn effortlessly. This engine is paired with a hydrostatic transmission that allows for smooth, responsive handling, making it easy to maneuver around obstacles while providing a top speed that reduces mowing time significantly.

One of the most remarkable features of the H924RX is its 54-inch heavy-duty fabricated deck. This wide cutting deck not only enhances productivity by covering more ground but also offers adjustable cutting heights for a customizable mowing experience. The unique design of the deck ensures an even cut and minimizes clumping, allowing for a healthier lawn appearance.

Simplicity has integrated their patented “Easy Ride” technology into the H924RX, which utilizes advanced torsion suspension to absorb shocks and vibrations. This feature increases comfort for the operator, especially during extended mowing sessions. Coupled with a plush high-back seat and ergonomic controls, the H924RX is designed for user-friendly operation.

In terms of technology, the mower is equipped with a state-of-the-art intuitive control panel, providing all the necessary information at a glance. Features like an integrated hour meter and fuel gauge ensure that users can easily track maintenance schedules and fuel levels. Additionally, LED headlights are included for enhanced visibility during early morning or late evening mowing sessions.

The build quality of the Simplicity H924RX is exceptional, with a heavy-duty frame and components designed to withstand rigorous use. This durability is complemented by an industry-leading warranty, offering peace of mind for users.

In summary, the Simplicity H924RX stands out as an impressive zero-turn mower, combining power, comfort, and advanced technology to meet the needs of every homeowner. Whether you’re maintaining a small yard or managing large expanses of grass, this mower provides the tools necessary for a beautiful lawn.
Top Page Image Contents