Orion Car Audio CO800.1, CO500.1 owner manual Tools of the Trade, End Panel Layouts, Input Plate

Page 4

TOOLS OF THE TRADE

Listed next are the majority of the tools required to perform an installation.. Having the proper tools will make the installation that much easier.. Some of these tools are necessities; some will just make the job easier..

● Allen Wrenches (2mm, 3mm & 4mm)	●	DMM or VOM
● Electric drill with assorted drill bits	●	Grommets
● Heat shrink tubing	●	Marking pen
● Phillips and flat blade screw drivers	●	Nylon tie straps
● Pliers (standard and needle nose)	●	Wire crimper
● RTA (real time analyzer)	●	Wire cutters
● Soldering iron and solder	●	Wire strippers

●Utility knife

●Wire brush or sandpaper for chassis grounding

●Reference CD with 1 kHz Sine Wave at 0dB level (all bits high)

End Panel Layouts

Input Plate

1

2

3

4

5

6

7

8

9

10

11

Figure 1

Figura 1

Abbildung 1

1.Power LED - When lit indicates that the amplifier is on..

2.High Level Input - Connect speaker output from factory radio to amplifier, will auto sense signal from radio and turn amplifier on when needed, turn off after 1 minute without signal..

3.RCA Outputs - provides a full range signal for easy connection to additional ampli- fiers..

4.RCA Inputs - Accepts RCA input from a source unit, preamplifier, or equalizer..

5.Gain Control - Continuously adjusts from 150mV to 8V input to obtain full power output..

6.Phase Control Switch - Allows for adjustment of phase and makes bridging ampli- fiers possible..

7.LPF, FULL, Switch - Selects either Lo-pass crossover or full range crossover..

8.Bass Boost Switch - Adjusts bass gain in three steps (0dB, 6dB, & 12dB)..

© 2007 directed electronics—all rights reserved

3

Image 4

Contents Amplifier Model Table of Contents WHAT’S in the BOX IntroductionPractice Safe Sound End Panel Layouts Tools of the TradeInput Plate CEA Specifications Output PlateAmplifier Settings High Level HarnessesAmplifier Wiring Power Connections for the Orion Cobalt CO500.1 and CO800.1Speaker Wiring Diagram CO500.1/CO800.1 Low-Pass CrossoverAmplifier Installation BridgingChoosing Mounting Locations Passenger CompartmentStep By Step Installation General Precautions and Installation TipsTrunk Compartment Set Up and Troubleshooting Testing the SystemAdjusting the Sound of the System Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Action To Take Amplifier Section CO500.1 CO800.1 SpecificationsCrossover Section Directed electronics-all rights reserved Panneau dentrée figure Agencement DES Panneaux DextrémitéPanneau de sortie figure Configurations dentrée et sortie du signal Spécifications DE LaceFaisceaux À Haut Niveau Réglages DE LamplificateurCâblage DE Lamplificateur Installation DE Lamplificateur Choix de lemplacement du montageCâblage des haut-parleurs CO500.1/CO800.1 Branchement en pontInstallation étape par étape Précautions générales et conseils dinstallationCoffre Réglage ET Dépannage Essai du systèmeRéglage sonore du système Conseils de dépannage Symptôme Cause probable FaireDirected electronics-all rights reserved Section amplificateur CO500.1 CO800.1 SpÉcificationsSection répartiteur Placa de entrada figura Disposiciones del panel de extremoPlaca de salida figura Configuraciones del amplificador Configuraciones de salida y entrada de señalEspecificaciones de la CEA Arneses DE Cableado DE Alto NivelCableado del amplificador Diagrama de cableado de altavoces del CO500.1/CO800.1 Instalación del amplificadorConexión en puente Selección de ubicaciones de montajeMaletero Compartimiento de pasajerosPrecauciones generales y sugerencias de instalación Instalación paso a paso Configuración y detección y reparación de averíasPrueba del sistema Ajuste de sonido del sistema Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarVuelva a ajustar los crossovers.. Consulte la sec Sección de amplificador CO500.1 CO800.1 EspecificacionesSección de crossover Anschlussplatte abbildung Layout DER EndplattenAusgangsplatte abbildung Signaleingangs- und -ausgangskonfigurationen CEA-DATENHOCHPEGEL-LEITUNGSSYSTEME VerstärkereinstellungenVerstärkeranschluss Verstärkerinstallation Lautsprecher-Anschlussdiagramm CO500.1/CO800.1Brückenmodus Wahl der EinbaustelleFahrgastraum Allgemeine Vorsichts- und InstallationshinweiseKofferraum Schrittweise Installation Einrichtung und ProblembehebungSystemtest Systemsound einstellen Problemlösungen Symptom Mögliche Ursache LösungDirected electronics-all rights reserved Verstärkerbereich CO500.1 CO800.1 DatenCrossover-Bereich Pannello d’ingresso figura Layout DEI Pannelli TerminaliPannello di uscita figura Configurazione dei segnali d’ingresso e di uscita Specifiche CEACavi DI Livello Alto Impostazioni dell’amplificatoreCablaggio dell’amplificatore Scelta del punto di installazione Installazione dell’amplificatoreCablaggio a ponte Abitacolo Precauzioni generali e suggerimenti per l’installazioneBagagliaio Procedura di installazione Messa a punto e soluzione dei problemiProva dell’impianto Regolazione dell’audio dell’impianto Soluzione dei problemi Sintomo Causa probabile Intervento necessarioDirected electronics-all rights reserved Sezione amplificatore CO500.1 CO800.1 Dati tecniciSezione crossover Painel de entrada figura Layouts DOS PainéisPainel de saída figura Configurações de entrada e saída dos sinais Especificações da CEALigações DE Alto Nível Ajustes do amplificadorConexão dos cabos do amplificador Instalação do amplificador Esquema de conexão dos alto-falantes ao CO500.1/CO800.1Ligação em ponte Escolha de locais de instalaçãoPorta-malas Cabine de passageirosPrecauções gerais e sugestões de instalação Instalação passo a passo Instalação e resolução de problemasComo testar o sistema Como ajustar o som do sistema Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaReajuste os crossovers.. Consulte as instruções Seção do amplificador CO500.1 CO800.1 EspecificaçõesSeção do crossover Warranty