Wolfcraft 6156, 6155 manual Making Combination Joints

Page 40

NOTE: Dovetail joint is used to connect (lengthen) two straight boards in this application.

5.Stand them vertically on the router table near the router bit, making sure the bottom of the two wood pieces are flush with the tabletop.

6.With the fence removed and using a block of wood as a push shoe so that the tail is not torn out, run the pieces through the router. This makes your first cut and leaves a tail on piece that was offset. See Figure 47.

PUSH

BLOCK

Figure 47

7.Place clamped wood pieces over dovetail/box joint bar with cut straddling bar. Using your first cut as a guide, make the next cut.

8.Continue making your cuts across the entire width of the pieces of wood, using each previous cut as a guide. See Figure 48.

PUSH

BLOCK

Figure 48

9. Assemble joint and test for fit.

NOTE: Move the dovetail/box joint bar slightly towards the bit to make the joint slightly looser; move the bar away from the bit to make the joint slightly tighter.

Making Combination Joints

A combination joint is comprised of a dado cut and a rabbet cut.

1.Set up router with same 3/8" bit height and the same spacing as for dovetail or box joints.

2.Lay a 3/4" piece of wood on the tabletop. With it snuggly against the dovetail bar, run it over the bit. This makes the dado cut. See Figure 49.

Figure 49

40

Image 40

Contents Wolfcraft Table of Contents WarrantySafety Instructions Unpacking and Checking Contents Introduction6156 Router Table features include Features and SpecificationsAdditional 6155 Router Table features include Package Contents & Hardware Legend Package Contents & Hardware Legend Package Contents & Hardware Legend Package Contents & Hardware Legend Package Contents & Hardware Legend Package Contents & Hardware Legend Assembly Tools RequiredAssemble Metal Miter Guide AF, zinc AG, black AH, black AJ, zincAttach Switch Box to Tabletop Assemble Plastic Miter GuideAG, zinc AH, black AJ, zinc AK, black AL, blackAttach Square Nuts and Retainers Attach ExtensionsAM, zinc AJ, zinc AN, black AP, black AQ, blackAttach Height-Adjustable Legs Attach Supports to TabletopAttach Height-Adjustable Legs Safety STICKERB-2 Safety StickerAttach Short Legs Alignment of Tabletop and ExtensionsAttach Optional, Second Shelf Router Table Model Only Attach Tool Tray Router Table Model 6155 OnlyAR, black AS, black AT, black Assemble Push Shoe Assemble Jointing Fence to Router Table FenceAU 1 black AV 2 black AW 1 black AX 1 zinc AH 1 blackAssemble Push Shoe to Fence Attach Security Guard FenceAY, zinc AZ, black Mounting the Router Hole Router Brand Specific ModelMounting Routers with Square Adaptor Plate Mount Router Directly to the TableBA, black 5 6 Alinee CON EL Agujero EN LA Placa AdaptadoraPage Router Base Plate Template Square Adaptor Weldnut Plate Z Securing the Router Table Model 6156 Only Switch BOX IntroductionElectrical Hookup Replace Damaged CordsSwitch Box Familiarization Risk of Electric ShockFor Routers With LOCK-ON Feature Operation of Switch Box and RouterCircuit Breaker Assembling Fence to the Router Table Assemble Inserts Insert UseConnecting a Vacuum Using your router/router tableSetting Depth/Height of the Cut OperationUsing the Router for Beading and Edge Cutting Jointing Push Shoe Clamp PlateFence Insert Using the Router as a Jointer Using the Fence with Board for Larger Workpieces Inside RoutingOutside Routing Routing Irregular WorkpiecesBB, black PIN Storage Starting PIN in Mounting HoleUsing the Miter Guage and Fence BC, black BD, black BE, zinc BF, zincSpacer BAR BIT Dovetail Boxjoint Mounting the BarClamp Offset Making Combination Joints Box Construction Using the Featherboard Flaps Repair Parts 6155/6156 Router Table All Parts KEYKEY Hardware BagsDescription QTY Repair Parts 6156 Router Table Table DES Matieres ÍndiceConsignes DE Sécurité Déballer ET Vérifier LE Contenu Caractéristiques ET Fiche Technique Contenu DE Lemballage ET Légende DU Matériel Contenu DE Lemballage ET Légende DU Matériel suite Article Description QTÉ Artículo Descripción CantContenu DE Lemballage ET Légende DU Matériel suite Contenu DE Lemballage ET Légende DU Matériel suite 24 AS 24 AT Contenu DE Lemballage ET Légende DU Matériel suite ASSEMBLAGE/ARMADO Outils requis/Herramientas necesariasAssembler le guide à onglets métallique Arme la guía de ingletes de metalAssembler le guide à onglets en plastique Arme la guía de ingletes de plásticoAG, zinc AH, noir/negro AJ, zinc AK, noir/negro AL, noir/negroFente DE Guide À Onglets Ranura DE LA Guía DE Ingletes AN, noir/negro AP, noir/negro AQ, noir/negro Fixer les pieds à hauteur réglableFixer les pieds à hauteur réglable suite Fixer les pieds courts Instale las patas cortasAJ, zinc AP, noir/negro AN, noir/negro AQ, noir/negro Alignement de la table et des rallongesFixer le plateau à outils Instale la bandeja de herramientasAR, noir/negro AS, noir/negro AT, noir/negro Fixer la deuxième étagère optionnelleAX 1 zinc AH 1 noir/negro AU AV TFigura Montage DE LA TOUPILLEUSE/CÓMO Montar LA Fresadora Lets Écrou À Tuerca Souder Soldada Modèle 6156 seulement Modelo 6156 solamenteBoîte DINTERRUPTEUR/CAJA DEL Interruptor Introduction / IntroducciónAvertissement Para fresadoras con la característica de LOCK-ON Pour les toupilleuses équipées dune fonction VerrouillageDisjoncteur/Interruptor automático Assemblage DU Guide À LA Table À Toupie Cómo Armar LA Barrera Guía a LA Mesa DE FresadoraAssembler les inserts Arme los insertos Utilisation de linsert Uso de insertosBranchement dun aspirateur UTILISATION/OPERACIÓNCómo conectar vacío Cómo usar la fresadora para corte de molduras y rebordes Débrancher la toupilleuse pour Poignées DE Guide Botones DE LA Barrera Guía Toupiller à lintérieur/Fresado interior Toupiller à lextérieur/Fresado exterior BB, noir/negroBC, noir/negro BD, noir/negro BE, zinc BF, zinc Montage de la barre Montaje de la barra Faire une queue daronde standard joints et joints à rainuresBloc Arrière Bloque DE Empuje Construction dune boîte Construcción de cajaUtilisation des rabats à lamelles Cómo usar las aletas de las tablas de sujeciónPiezas Para Reparación Mesa de fresadora Toutes les pièces / Todas las piezas Descripción CantSacs de matériel/Bolsas para CLÉ N ArticleDescription QTÉ Descripción CantClave No. Artículo Wolfcraft Product Registration Card NameWolfcraft