INDICATION
MANDATORY INFORMATION INSTRUCTION
WARNINGPROHIBITION
These signs will give advice for your safety
Before leaving our factory every machine is thoroughly tested.
Follow our instructions strictly and your machine will give you long service in normal operating conditions.
1.Uses
Use: Wet sawing of old and new concrete and asphalt. Dry sawing only with blade manufacturers approval of specific application.
Tools: Diamond blades — water cooled, Ø: 14”(350mm), 18” (450mm), 20” (500mm),24” (600mm), 26” (650mm), 30” (750mm), and 36” (900mm) with Arbor Ø - 1”.
(For information, contact your supplier.)
Depths of Cut (Maximum): | Blade | Depth | |||
| Blade | Depth | |||
| 14” | 4.5” | 350mm | 110mm |
|
| 18” | 6.5” | 450mm | 160mm | |
| 20” | 7.5” | 500mm | 175mm | |
| 24” | 9.5” | 600mm | 225mm | |
| 26” | 10.5” | 650mm | 260mm | |
| 30” | 12.5” | 750mm | 310mm | |
| 36” | 15.0” | 900mm | 375mm | |
Before starting up the machine, make sure you read this entire manual and are familiar with the operation of this machine.
The working area must be completely clear, well lit and all safety hazards removed.
T h e o p e r a t o r m u s t wear protective clothing appropriate to the work he is doing.
Any persons not involved in the work should leave the area.
Use only blades marked with a maximum operating speed greater than the blade shaft speed.
50
2.Moving The Machine
(See Figures 1, 2 and 5)
Set The Handles To The Desired Length:
•Loosen Knob (1A), pull the Handle Bar (1B) in or out to desired length, then tighten the Knob (1A) to adjust Handle Bar height, Turn Handle Bar Adjustment Lock (1R) counterclockwise to unlock. Adjust Handle Bar (1B) to the desired height. Turn HANDLE ADJUSTMENT LOCK (1R), clockwise to lock in place.
Front Pivot Model (with Electric Tracking System – If equipped)
Moving The Saw With The Engine Off:
•Turn ENGINE START SWITCH (1H) to the “1” (RUN) position.
•Raise the saw by pressing up on the TOGGLE SWITCH (1P) on SPEED CONTROL LEVER (1O) until the DIAMOND BLADE (2E) (if installed) clears the pavement surface.
•Put SPEED CONTROL LEVER (1O) into the STOP POSITION (1BB).
•Set TRANSMISSION BYPASS VALVE (6J) counterclockwise to the up (NEUTRAL) position.
•The saw can now be moved by standing behind it and pushing [while holding the Handle Bars (1B)].
DO NOT attempt to push the saw while it is in NEUTRAL on a grade (or hill). The saw operator could lose control of the saw and cause injury to himself or other persons in
the area.
Moving The Saw With Engine On:
•Raise the saw by pressing up on the TOGGLE SWITCH (1P) on SPEED CONTROL LEVER (1O) until DIAMOND BLADE (2E) (if installed) clears the pavement surface.
•Set WATER SAFETY SWITCH (1L) button to the “0” (OFF) position.
•SPEED CONTROL LEVER (1O) must be in the STOP POSITION (1BB) to start the saw. The engine WILL NOT start unless SPEED CONTROL LEVER (1O) is in the STOP POSITION (1BB).
•Check that TRANSMISSION BYPASS VALVE (6J) is turned clockwise (DOWN) to the closed position. Do NOT start the engine if the valve (6J) is in the Neutral (OPEN) position.
•Turn ENGINE THROTTLE (1F) to a low speed setting.
•Set BLADE CLUTCH SWITCH (1V) (if equipped) to “0” (OFF).
*In cold conditions (below 32° F (0° C)) push in on the ENGINE START SWITCH (1H) for 15 seconds. This preheats the engine for cold weather starting.
•Turn the ENGINE START SWITCH (1H) to the “2” (START) position until the engine starts, then release the switch. It will return to RUN position. If the engine does not start, repeat these steps.