Husqvarna FS4800D manuel dutilisation Using the Blade Depth Indicator 1Q

Page 53

•Start the engine using the ENGINE START SWITCH (1H). Follow the procedure in the engine manual. In Cold conditions, pre-heat the engine by holding in the ENGINE START SWITCH (1H) for 15 seconds.

•Let the engine warm up for several minutes with ENGINE THROTTLE (1F) at the low speed setting.

•When ready, open the WATER VALVE (1T).

•Set WATER SAFETY SWITCH (1L) to “1” (ON).

Test for adequate water supply. (2.5 - 5.0 GPM) (10 - 20 Liters per Minute) Low water flow will cause damage to diamond blades.

•For Machines without the Optional BLADE CLUTCH SWITCH (1V): Pull ENGINE THROTTLE (1F) out to set engine RPM at 3200, as shown on the ENGINE TACHOMETER (1G).

See chart for the appropriate blade shaft and engine speeds for specifc blade sizes.

•Move the saw forward or reverse (Standard and Front Pivot Models) slowly by pushing or pulling on the Speed Control Lever (1O). Move the saw slowly to prevent stalling the blade. Make sure the Front Guide (6D), Rear Guide (6F) and DIAMOND BLADE (2E) stay on the line.

Rear Pivot Model Only: For the Rear Pivot Model, aligning to the cutting line can be made using the pivot feature on the machine. Simply move the DIFFERENTIAL SWITCH (1J) to the Left position (Pivot), and then use both hands to push down on the HANDLEBARS (6G), and the machine can be pivoted from side to side to align with the cutting line. After the saw is properly aligned to the cutting line, toggle the DIFFERENTIAL SWITCH (1J) to the Center (Lock) position.

•Set the BLADE CLUTCH SWITCH (1V) (if equipped) to “1” (ON) to engage the Blade Drive when engine is at IDLE SPEED (1200 RPM or less)! When clutch engages and blade is at idle speed, pull out ENGINE THROTTLE (1F) and set engine RPM at 3200.

•Lower the saw by pressing the TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) downward until the DIAMOND BLADE (2E) is at the desired cutting depth (See “Blade Cutting Depth Information”).

Be certain that water flow is abundant for wet sawing.

Blade Cutting Depth Information:

The saw is equipped with a BLADE DEPTH INDICATOR (1Q) which has two number ranges. The Orange and White number ranges are used for two different purposes:

1)The “Depth” number range, indicated by the Orange color, shows the current Cutting Depth of the DIAMOND BLADE (2E). As the saw is lowered, the BLADE DEPTH INDICATOR (1Q) needle travels through these numbers in increasing order. Or

2)The “SMD” or “Set Maximum Depth” number range, indicated by the White color, is the uncut depth of the DIAMOND BLADE (2E). The desired maximum cutting depth is pre-set using the BLADE DEPTH INDICATOR (1Q). It can be used with or without the BLADE DEPTH STOP SWITCH (1M) feature. As the saw is lowered, the BLADE DEPTH INDICATOR (1Q) needle travels through the White color number range in decreasing order, indicating the unfinished depth of cut. When the BLADE DEPTH INDICATOR (1Q) needle reaches “0” position, the desired maximum cutting depth is reached. If the BLADE DEPTH STOP SWITCH (1M) feature is used (“1” or “ON” position), the lowering process stops automatically.

Using the BLADE DEPTH INDICATOR (1Q):

“Depth” Mode (Orange colored numbers show current cutting depth):

•Turn ENGINE START SWITCH (1H) to “0” (OFF) position to STOP engine (If running).

•Turn ENGINE START SWITCH (1H) to “1” (RUN) position to power electrical system.

•Turn BLADE DEPTH STOP SWITCH (1M) to “0” (OFF) position.

•Lower DIAMOND BLADE (2E) by pushing the TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) downward until the DIAMOND BLADE (2E) touches the surface to be cut.

•Rotate the BLADE DEPTH INDICATOR (1Q) needle to align to the “0” depth.

•As DIAMOND BLADE (2E) is lowered into the cutting surface, the current cutting depth will now be indicated by the Orange text number range on BLADE DEPTH INDICATOR (1Q) needle.

SMD or “Set Maximum Depth” Mode without BLADE DEPTH STOP (White colored numbers show uncut depth):

•Turn ENGINE START SWITCH (1H) to “0” (OFF) position to STOP engine (If running).

•Turn ENGINE START SWITCH (1H) to “1” (RUN) position to power electrical system.

•Lower DIAMOND BLADE (2E) by pushing TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) downward until DIAMOND BLADE (2E) touches the surface to be cut.

•Rotate the BLADE DEPTH INDICATOR (1Q) needle to align with the desired maximum cutting depth on White colored number range. The uncut depth will now be indicated on the White colored number range. When the BLADE DEPTH INDICATOR (1Q) needle gets to the “0” position, the saw is cutting at the desired maximum cutting depth.

•Raise the blade by pushing the TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) upward until the DIAMOND BLADE (2E) is off of the cutting surface.

•Turn the ENGINE START SWITCH (1H) to the “0” (OFF) position to turn off power to electrical system.

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents FS 4800 D USA Déclaration DE Conformité À LA Directive « Machines »Notas Remarque Table of Contents Instrucciones Diagramas EsquemáticosDE Página Schémas Figures DE Référence InstructionsNotas Remarque Blade Safety FirstUSA Do notAdvertencias Advertencias Usure inhabituelle, NE PAS Utiliser LE Disque FaireNE PAS Faire Page Page Page Page Page Page Page Page MAY RESULT. Hearing Protection Required General InformationCalifornia Prop 65 Warning Dust WarningSound Level Technical Data Sound Level, EMC, and HAVInformación general AdvertenciaPeligro Para LA AUDICIóN Advertencia de la Proposición 65 del Estado de California Advertencia Relativa AL PolvoNivel sonoro Datos técnicos Nivel sonoro, EMC y HAVInformation générale AvertissementProposition 65 de Californie Avertissement Avertissement Relatif À LA PoussièreNiveau sonore Données techniques niveau sonore, CEM et VMBNotas Remarque THROTTLE, Diesel Operating InstructionsCrush Hazard Sound Level CEDECAL, Husqvarna FS4800D Manual Axle AdjustmentDECAL, 3 HSQ Crown Gearbox OperationPatents TOP of Blade Guard 542 16Blade RPM & Size Gearbox Range / Blade RPMTOP of Engine Hood Near Shift Lever Shift Lever POSITION-4.5 FlangeShift Lever POSITION-5.0 Flange Shift Lever POSITION-6.0 FlangePower Source Standard FeaturesFS 4800 Diesel Model EngineFS 4800 D Diesel Specifications Características Estándar Modelo Diesel FSFuente DE Alimentación MotorEspecificaciones DE Diesel FS 4800 D Caractéristiques Standards FS 4800 Modèle DiéselSource D’ALIMENTATION MoteurSpécifications DU FS 4800 D Diesel Instructions Spéciales Special InstructionsInstrucciones Especiales Page Service Every 50 Hours Service DailyService Every 100 Hours Service Every 250 Hours1U. SAW Lowering Speed Control Knob 2C. Outer Flange Arbor Use to support the Diamond Blade 2E OIL / Water Separator1Y. Radiator Coolant Overflow Bottle 1N. Gearbox Pulley 1M. V-BELTS Set of 4, 3 Groove2M. V-BELTS Set of 4, 3 Groove 5A. AIR Filter Assembly Includes2N. Gearbox Pulley 5F. Fuel Filter 5G. AIR Filter Rain CAP6M. Alternator / Waterpump Belt Self Do not Operate Engine with Shields or Guards Removed6K. Hydrostatic Transmission Pump Indication Mandatory Information Instruction Uses Moving The Machine Check Before Starting Transport Blade RemovedSee Figures 1, 2, To Transport By VehicleFitting The Blade To Install a SLIP-ON GuardStarting The Saw See Figures 1Using the Blade Depth Indicator 1Q Stopping The Saw Adjustments Straight Line SawingIncidents During Sawing SAW Lowers TOO FastMaintenance Blade Shaft V-Belt Tension Important AdviceHydraulic System Fuel FilterEngine Speed Engine / Blade Shaft / Gearbox Speed AdjustmentBlade Shaft Speed Single Speed Gearbox ModelSee Blade Size Conversion charts for specific information AccessoriesRepairs Spare PartsReferencia Rápida Para Mantenimiento Programado Lista DE Comprobación Preliminar1L. Interruptor DE Seguridad DEL Agua 1H. Interruptor DE Arranque DEL Motor1I. Medidor DE Voltaje Indica el voltaje del 1Z. Interruptor Selector DEL Tacómetro 1O. Palanca DE Control DE Velocidad1A. Caja DE Engranajes DEL Motor Modelo 1N. Polea DE LA Caja DE Engranajes 1M. Correas Trapezoidales Juego de2A. Caja DE Engranajes DEL Motor Modelo 2M. Correas Trapezoidales Juego de 4, 3 ranuras5A. Conjunto DEL Filtro DE Aire Incluye 2P. Perilla DE Retención DE LA Caja DE6K. Bomba DE Transmisión Hidrostática Filtro Hidráulico Filtra el fluido del sistemaHidráulico Traslado de la máquina UsosEstos avisos le dan Consejos por su seguridad Profundidades de corte máxima HojaPara transporte en vehículo Transporte sin la hojaVea las figuras 1, 2 y Colocación de la hoja Revisiones antes del arranqueVea las figuras 1 y Protecto DE LA Hoja 2GPara instalar un Protector Deslizante Arranque de la sierraUso del Indicador DE Profundidad DE LA Hoja 1Q Incidentes durante el corte con sierra Parada de la sierraAjustes Corte en línea recta LA Sierra Desciende Demasiado RápidoMantenimiento Sistema hidráulico Tensión de la correa trapezoidal del eje de la hojaConsejo importante Ruedas Y CubosVelocidad DEL EJE DE LA Hoja Velocidad DEL MotorModelo DE Caja DE Engranajes DE UNA Velocidad 152 mmReparaciones AccesoriosPiezas de repuesto 127 mmGuide Rapide DU Calendrier D’ENTRETIEN Liste DE Vérification Avant Utilisation1O. Levier DE Commande DE Vitesse Accélérateur DU Moteur CommandeE R M O M È T R E D U L I Q U I D E D E EN Diamant 2E 1H. Contacteur DE Démarrage DU Moteur1DD. Élément DU Filtre À AIR DU Radiateur 1Q. Indicateur DE Profondeur DU Disque1V. Commutateur D’EMBRAYAGE DU Disque 1A. Boîte DE Transmission DU Moteur Modèle 2N. Poulie DE Boîte DE Transmission 1N. Poulie DE Boîte DE Transmission5A. Ensemble DU Filtre À AIR L’ensemble 2P. Bouton DE Cran DE LA Boîte DE6C. Protections ET Écrans DE Courroie Remplissageduréservoirhydraulique6J. Robinetdedérivationdelatransmission 6K. Pompe DE Transmission HydrostatiqueLevier DU Frein D’IMMOBILISATION 7A Déplacement de la scie avec le moteur arrêté Déplacement de la machineUtilisations Ces signes donnent des conseils Pour la sécuritéTransport disque retiré Mise en place du disquer Vérifier avant de démarrerTransport de la machine sur un véhicule Voir les figures 1 etDémarrage de la scie Pour installer une Protection AmovibleUtilisation de l’INDICATEUR DE Profondeur DU Disque 1Q LA Scie S’ABAISSE Trop Rapidement Arrêt de la scieIncidents pouvant se produire durant le sciage Entretien Réglages Sciage en ligne droiteFiltre À AIR Tension des courroies trapézoïdales de l’axe du disqueRoues ET Moyeux Filtre À CarburantConseil important Circuit hydrauliqueDisque EN Diamant Régime Moteur Vitesse DE L’AXE DU DisquePage 16 Réparations Accessoires17 Pièces détachées Kits DE Conversion DES Protections DE Disque350mm Convert To Size450mm 600mm650mm 350115mm 850mmFS4800 D Diesel Tabla DE Conversiones DE Tamaños DE LA 350-650 mm Convertir al tamaño14po Jusqu’à la taille450 mm 18 poFlasque 14-26po½po 115mm 14-30po101 102 103 104 105 106 107 108 109 110 Husqvarna South Carolina Husqvarna Corporate OfficeHusqvarna Canada Husqvarna International542 20
Top Page Image Contents