2 610 392 415 - Buch Seite 3 Dienstag, 10. Dezember 2002 7:52 07
|
|
| . |
|
| o | |
Before Putting into Operation | |||
| . |
| |
| r |
|
|
| . |
|
|
■ Before any work on the machine itself, pull | |||
the mains plug. | s |
|
|
|
|
| |
Riving Knife
Checkingprahathe Adjustment of the
For safety reasons t e riving knife 8 must always be used. The iving knife avoids seizing of the saw blade while sawing.
The adjustment takes place at the maximum cut- mikosoftting dep h. 
L sen the screw 6, adjust the riving knife 8 and retighten the screw.
6
8
2,5 - 5 mm
2,5 - 5 mm
|
|
|
|
|
| . |
Adjusting the Cutting Angle |
|
| o | |||
|
|
|
| . |
| |
|
|
| r |
|
| |
|
|
| . |
|
| |
■ Before any work on the machine itself, pull |
|
|
| |||
the mains plug. |
|
| s |
|
|
|
|
|
|
|
|
| |
Loosen winged screw(s) 5. | praha |
|
|
|
| |
|
|
|
|
| ||
Swing the machine to the side until the desired |
|
|
| |||
cutting angle is set on the scale 13. |
|
|
|
|
| |
Tighten winged screw(s) 5 again. |
|
|
|
|
| |
Note: For mitre cutting, the cutting depth is |
|
|
| |||
smaller than the value shown on the cutting depth |
|
|
| |||
scale 17. |
|
|
|
|
|
|
mikosoft |
|
|
|
|
|
|
Cutting Marks |
|
|
|
|
|
|
45° 0° |
| 45° 0° |
|
|
| |
Adjusting the Cutting Depth (see figure C )
■ Before any work on the machine itself, pull | The cutting mark 45° ( 15) indicates the position | |
of the saw blade for 45° cuts. | ||
the mains plug. | ||
|
To achieve an optimum cut, the saw blade | For an exactly true cut, apply the saw as shown |
☞ must not protrude more than 3 mm at the | in the diagrams. |
most from the material.
|
| For adjusting the cutting depth, loosen the |
|
|
|
|
|
|
|
|
|
|
| ||||
|
| winged screw/clamping lever (PKS 46) 18 and |
| Initial Operation |
|
|
|
| . | ||||||||
|
| raise the saw from, or lower it to the base plate 7: |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| |||||||
|
| Raise |
|
|
| . |
| Observe correct mains voltage: The voltage of |
| ||||||||
|
| ➡ for smaller cutting depths |
|
|
|
| |||||||||||
|
|
| the power source must agree with the voltage |
|
|
| |||||||||||
|
| Lower | ➡ |
|
| o |
| o | |||||||||
|
|
|
|
| specified on the |
|
|
|
| ||||||||
|
| for greater cutting.depths |
| nameplate of the machine . |
|
| |||||||||||
|
|
|
|
| r |
|
|
|
|
|
|
| r |
|
|
| |
|
| Set the desired depth on .the cutting depth |
| Equipment marked with 230 V can also be con- |
|
|
| ||||||||||
|
|
| nected to 220 V. |
|
| . |
|
|
| ||||||||
|
| scale 17. |
|
| s |
|
|
|
| s |
|
|
| ||||
|
| Tighten winged screw/cl |
|
|
|
|
|
|
|
|
|
| |||||
|
| mping lever 18 again. |
| Switching On and Off |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| For starting operation of the mac ine, actuate |
|
|
| ||||||
|
| Clamping Lever (PKS 46) |
|
|
| ||||||||||||
|
|
| the safety switch against starting 1 first, and then |
|
|
| |||||||||||
|
| The clam | ing | ower of the clamping lever 18 can |
| press and hold the On/Off switch 2 afterwards. |
|
|
| ||||||||
|
|
| To switch off the machine, release the On/Off |
|
|
| |||||||||||
|
| be adjusted. |
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| praha |
|
|
|
|
| ||
|
|
| praha |
|
|
| switch 2. |
|
|
|
|
|
| ||||
|
| To do his, unscrew the clamping lever and set it |
|
| For safety reasons the On /Off switch of |
|
|
| |||||||||
|
| at at least 30° |
|
|
|
|
| ||||||||||
mikosoft13 • 2 610 392 415 • TMS • 28.11.02 |
|
|
|
| the machine cannot be locked; it must |
|
|
| |||||||||
|
|
|
|
|
|
| |||||||||||
|
|
|
| remain pre | ed during the entire opera- |
|
|
| |||||||||
|
|
|
| tion. |
|
|
|
|
|
|
| ||||||
|
|
| mikosoft |
|
|
|
|
|
| ||||||||
| English - 3 |
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|