Display and Operation | A&D AD-4405 specification

8.1.2.Display and Operation

Action of Accumulating Data

			When accumulating data, the display blinks once.


			If the accumulated data is stored, the M+ mark is displayed.
Caution					This function can not accumulate data with a different unit. Specify a unit


					before use.

Display of Accumulated Data

When setting to Cf08 1 (Effective accumulation function) and pressing the TOTAL

key, total is displayed and the total data is displayed with the M+ mark blinking. Pressing the TOTAL key alternatively displays the accumulated data and the accumulation count. Pressing the ESC key, the weight data is displayed.

The total data can be output. Refer to "Output of Accumulation Data".

Undoing the Accumulation Data

The last weight data can be deduced from the accumulated data unless new data has been accumulated.


Step 1	Press the			TOTAL	key to display			total	and the accumulated data.
Step 2	Press and hold the +/- key for more than 3 seconds. The display blinks once and
	the data accumulated before accumulating the last weight data is displayed.
Caution			External input can not be used.


Clearing the Accumulation Data

Step 1	Press the			TOTAL	key to display			total	and the accumulated data.

Step 2	Press and hold the					ZERO	key more than 3 seconds. The display blinks once and
	the accumulated data is cleared.
Caution			External input can not be used.

Initializing the Data Number and Clearing the Accumulation Data at the same time

When the data number is included with the data of the serial data output or the printer, initializing the data number and clearing the accumulated data can be done at same time.

If using both serial output and printer data number, all data numbers are initialized by this operation.


Step 1	Press			TOTAL	key to display			total	and the accumulated data.

Step 2	Press and hold the					ZERO	and +/- keys at the same time for more than 3 seconds.
	The display blinks once and the accumulated data is cleared. And the data
	number is initialized (1).
Caution			External input can not be used.

AD-4405 Weighing Indicator

Page 35

8. Accumulation

Image 37

A&D AD-4405 manual Display and Operation

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Standard accessories Accessories and optionsSupplemental accessories for printer Options Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format To Get Stabilized Data Specifying the Second Range ResolutionSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Tare Digital Input Preset TareWeighing Tare Clearing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Description of Input parameters and Outputs Setpoint ComparisonF22 = 7 Check weighing Output and Condition Simple Batch F22 = 9 Check weighing 3Loss in weightStart Weighing Completion Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Hold Function Setting the Hold FunctionsDisplay and the Data Output of Hold and Average Relations to the Other Functions Conditions of the Average and Release Key input and command in the hold stateTARE, ZERO, SETPOINT, Total MT, MZ, HC Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time RS-232C Interface 16.1 SpecificationsCircuit and Pin Connection Bit Format Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Preset Tare Commands to Set ParametersSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands to Set the Data Output/ Print Format UFC Commands for the Hold FunctionStart Averaging to Hold Release the Hold Data UFC Command Parameters UFC Commands SF1,$ID$DN$CR$LF$GR$UT$CR$LF $DL’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF TRM RS-422/RS-485, Relay OutputOP-03COM Circuit Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Data Format Current Loop Output Analog Input and A/D Conversion SpecificationsDigital Section Interface General Dimensions Memo Memo Memo