Setpoint Comparison, F22 = 7 Check weighing | A&D AD-4405 specs

10.2. Setpoint Comparison

This function includes the weighing sequence and is used for acquiring a preset target weight.

There are four parameters of "Final", "Preliminary", "Free fall" and "Zero band" that use the setpoint comparison.

The result of the sequence is output to the three relays of OP-03, Op-05 or OP-08. When entering these parameters, it is not necessary to enter the F-function f22 again unless comparison conditions are changed.

10.2.1.Description of Input parameters and Outputs

F22 = 7 (Check weighing 1)

Preset target weight

Weighing value
	Weighing trace
Final	Free fall
	Free fall
	Tare
Tared Zero	Zero band
	Zero band
Calibrated Zero
Output and Condition	Time

Relay HI,	1, Net ] (Final - Free fall)	OFF
Relay LO,	Gross ¢ Zero band	ON

ON

OFF

OFF

ON

Relay OK output can be changed to OVER or UNDER by setting f24. Triangle 2 is not displayed.

OVER/UNDER is judged always and the result is output to the LED and the relay.

F22 = 8 (Check weighing 2)

Preset target weight

Weighing value
	Weighing trace
Final	Free fall
	Free fall
Preliminary
	Tare
Tared Zero	Zero band
	Zero band
Calibrated Zero

Output and Condition

Relay HI, 1, Net ] (Final - Free fall) Relay OK, 2, Net ] (Final - Preliminary) Relay LO, 3, Gross ¢ Zero band

OFF

OFF

ON

ON

ON

OFF

Time

OFF

OFF

ON

OVER/UNDER is judged always and the result is output to the LED but not to the

relay.

AD-4405 Weighing Indicator

Page 41

10.2. Setpoint Comparison

Image 43

A&D AD-4405 Setpoint Comparison, Description of Input parameters and Outputs, F22 = 7 Check weighing, Output and Condition

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Options Accessories and optionsStandard accessories Supplemental accessories for printer Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format Specifying the Second Range Capacity Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Weighing Range of the First Range Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Clearing Tare Digital Input Preset TareTare Weighing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Output and Condition Setpoint ComparisonDescription of Input parameters and Outputs F22 = 7 Check weighing Weighing Completion F22 = 9 Check weighing 3Loss in weightSimple Batch Start Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Relations to the Other Functions Setting the Hold FunctionsHold Function Display and the Data Output of Hold and Average MT, MZ, HC Key input and command in the hold stateConditions of the Average and Release TARE, ZERO, SETPOINT, Total Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time Bit Format 16.1 SpecificationsRS-232C Interface Circuit and Pin Connection Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Limit/Setpoint Value Commands to Set ParametersSet the Preset Tare Set the Unit Weight for Counting Mode Release the Hold Data Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Start Averaging to Hold UFC Command Parameters UFC Commands PF2,$DT$TM$LF$AN$SP$TL$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF ’$AN$TL$LF$LF Circuit RS-422/RS-485, Relay OutputOP-03TRM COM Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Data Format Current Loop Output Interface SpecificationsAnalog Input and A/D Conversion Digital Section General Dimensions Memo Memo Memo