Commands to Control the Indicator | A&D AD-4405 specification

16.3.2.Commands to Control the Indicator

Zero the Display

Sets the current display to the zero point.

Template	MZ

Command	M	Z

Reply	M	Z

Tare

Sets the current display to zero of the net data.

Template	MT
Command
Command	M	T
Reply
Reply	M	T

Clear the Tare Data

Clears the tare data and displays the gross data.

Template	CT

Command	C	T

Reply	C	T

Display the Gross Data

Displays the gross data.

Template	MG

Command	M	G
Reply
Reply	M	G

Display the Net Data

Displays the net data.

Template

Command

Reply

MN

MN M N

Accumulation (M+)

Accumulates the displayed data.

Template	MA
Command
Command	M	A
Reply
Reply	M	A

Clearing the Accumulated data

Clears the accumulated data.

Template

Command

Reply

CA

CA C A

16.3. Command Format

Page 60

AD-4405 Weighing Indicator

Image 62

A&D AD-4405 manual Commands to Control the Indicator

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Supplemental accessories for printer Accessories and optionsStandard accessories Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison LO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and Condition Start F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing Completion Returns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other Functions TARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HC Counting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output Circuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Set the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint Value Start Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold Data UFC Commands UFC Command Parameters ’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LF COM RS-422/RS-485, Relay OutputOP-03TRM Circuit Switching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Current Loop Output Data Format Digital Section SpecificationsAnalog Input and A/D Conversion Interface Dimensions General Memo Memo Memo