Internal Printer OP-06 | A&D AD-4405 specs

14. Internal Printer (OP-06)

A dot matrix type printer (OP-06) can be installed in the AD-4405. It can print out the result of weighing, accumulated weight, date and time, etc. The print format can be arranged by the F-Function settings or by using the serial interface command.

Print

When in the manual print mode, by pressing the PRINT key to print in format 1, and pressing the MODE key while pressing the PRINT key, the print out is done using format 2.

The print out format is set at f70 for format 1 and at f71 for format 2 of the F-Functions.

The print out format can be set using the serial interface (OP-03, OP-05 and/or OP-08). Refer to “16.3.5. Commands to Set the Data Output/ Print Format (UFC)”. The number of repeated printings of the same contents separately, in format 1 and format 2, can be set at f62.

The number of lines that feed before or after the print out separately, in format 1 and format 2, can be set at f63 and/or f64.

The direction of the characters can be set at f65.

Examples
All characters	Date, time, data number, code, gross and net

Initial setting print out	Parameters 92 and 95

AD-4405 Weighing Indicator

Page 51

14. Internal Printer (OP-06)

Image 53

A&D AD-4405 manual Internal Printer OP-06

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Standard accessories Accessories and optionsSupplemental accessories for printer Options Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format To Get Stabilized Data Specifying the Second Range ResolutionSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Tare Digital Input Preset TareWeighing Tare Clearing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode LO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode Description of Input parameters and Outputs Setpoint ComparisonF22 = 7 Check weighing Output and Condition Simple Batch F22 = 9 Check weighing 3Loss in weightStart Weighing Completion Returns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Hold Function Setting the Hold FunctionsDisplay and the Data Output of Hold and Average Relations to the Other Functions Conditions of the Average and Release Key input and command in the hold stateTARE, ZERO, SETPOINT, Total MT, MZ, HC Counting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time RS-232C Interface 16.1 SpecificationsCircuit and Pin Connection Bit Format Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Preset Tare Commands to Set ParametersSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands to Set the Data Output/ Print Format UFC Commands for the Hold FunctionStart Averaging to Hold Release the Hold Data UFC Command Parameters UFC Commands SF1,$ID$DN$CR$LF$GR$UT$CR$LF $DL’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF TRM RS-422/RS-485, Relay OutputOP-03COM Circuit Switching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Data Format Current Loop Output Analog Input and A/D Conversion SpecificationsDigital Section Interface General Dimensions Memo Memo Memo