Installation and Precautions, Load Cell Connections | A&D AD-4405

3. Installation and Precautions

3.1.1.Installation and Precautions

The AD-4405 weighing indicator is a precision electronic instrument. Handle the indicator carefully.

The operating temperature is -10°C to +40°C (14°F to 104°F).

Do not install the scale in direct sunlight.

Mis-operation or other problems may be caused by an unstable power source including momentary power failure or instantaneous noise. Use a stable power source.

Do not connect the power cord before the installation has been completed. Verify that the local voltage and receptacle type are correct for your scale.

Use shielded cable for all connections. Connect the cable shields to the shield terminal or case as an earth terminal.

Earth ground the indicator. Do not join the earth ground line with other electrical power equipment. There is an earth ground terminal at the power cord receptacle. Do not install the indicator in a place where it is apt to be charged with static electricity, or where the relative humidity is lower than 45%RH. Plastic and insulating materials are apt to be charged with static electricity.

3.1.2.The Load Cell Connections

Connect the load cell wires to the connector (receptacle), at the rear panel, using the accessory load cell plug.

It is possible to connect a 4 wire cable provided that pins 1-2 and pins 3-4 are shorted, if the distance between the indicator and the load cell is shorter than 5m. The output voltage of a load cell is a very sensitive signal. Space the load cell cable away from any noise source.

It is possible to connect four 350ohm load cells.

The load cell drive is 5VDC 5% between EXC+ and EXC-, the maximum current 60mA.

AD-4405 Weighing Indicator

Page 5

3. Installation and Precautions

Image 7

A&D AD-4405 manual Installation and Precautions, Load Cell Connections

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Options Accessories and optionsStandard accessories Supplemental accessories for printer Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format Specifying the Second Range Capacity Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Weighing Range of the First Range Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Clearing Tare Digital Input Preset TareTare Weighing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Output and Condition Setpoint ComparisonDescription of Input parameters and Outputs F22 = 7 Check weighing Weighing Completion F22 = 9 Check weighing 3Loss in weightSimple Batch Start Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Relations to the Other Functions Setting the Hold FunctionsHold Function Display and the Data Output of Hold and Average MT, MZ, HC Key input and command in the hold stateConditions of the Average and Release TARE, ZERO, SETPOINT, Total Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time Bit Format 16.1 SpecificationsRS-232C Interface Circuit and Pin Connection Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Limit/Setpoint Value Commands to Set ParametersSet the Preset Tare Set the Unit Weight for Counting Mode Release the Hold Data Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Start Averaging to Hold UFC Command Parameters UFC Commands PF2,$DT$TM$LF$AN$SP$TL$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF ’$AN$TL$LF$LF Circuit RS-422/RS-485, Relay OutputOP-03TRM COM Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Data Format Current Loop Output Interface SpecificationsAnalog Input and A/D Conversion Digital Section General Dimensions Memo Memo Memo