Commands to Set Parameters, Set the Zero Band | A&D AD-4405 guide

SZ, [ value ]

S Z , + 7 4 8

S Z , + 7 4 8

16.3.3.Commands to Set Parameters

Set the Limit/Setpoint Value

Sets the limit or setpoint value of the comparison. The decimal point is not necessary. Template Sm,n, [ value ]

m: code memory number, 0 - 4

n : setpoint order number, refer to "Setting the setpoint"

Command Reply

S1 , 3 , + 1 6 0 S 1 , 3 , + 1 6 0

Set the Zero Band

Sets the F26 value (zero band) of the comparison. The decimal point is not necessary.

Template

Command

Reply

Set the Preset Tare

Sets the preset tare value. The decimal point is not necessary.

Template PT,m, [ value ]

m: code memory number, 0 - 4

Command Reply

PT , 2 , 2 1 3 P T , 2 , 2 1 3

Set the Unit Weight for Counting Mode

Sets the unit weight value with decimal point. Template UW,m, [ value ]

m: code memory number, 0 - 4

Command Reply

UW , 2 , 2 1 . 3 U W , 2 , 2 1 . 3

16.3. Command Format

Page 62

AD-4405 Weighing Indicator

Image 64

A&D AD-4405 manual Commands to Set Parameters, Set the Limit/Setpoint Value, Set the Zero Band, Set the Preset Tare

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Accessories and options Standard accessoriesSupplemental accessories for printer Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and Condition F22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing Completion Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other Functions Key input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HC Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output 16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Commands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold Data UFC Commands UFC Command Parameters $DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF RS-422/RS-485, Relay OutputOP-03 TRMCOM Circuit Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Current Loop Output Data Format Specifications Analog Input and A/D ConversionDigital Section Interface Dimensions General Memo Memo Memo