Accessories and options, Standard accessories | A&D AD-4405 specification

4.1.4.Accessories and options

Standard accessories

					Instruction manual	1
					Load cell plug	1	JM-NJC-207-PF
	Accessories				0.2A or 0.315A time lag fuse	1	FS-EAWK-200MA
	Accessories						FS-EAWK-315MA
							FS-EAWK-315MA
					Capacity label	1
					Function seal	1
Caution			Please confirm that the receptacle type and local voltage is correct for
			your indicator (scale).
Options
	OP-03 (AD-4405-03) *			RS-422/485 interface, 3-Relay outputs
	OP-05 (AD-4405-05) *			RS-232C interface, 3-Relay outputs and 3-Control inputs
	OP-06	(AD-4405-06)		Built-in dot matrix impact printer (16 characters/line)
	OP-07	(AD-4405-07) *		4-20mA analog output
	OP-08	(AD-4405-08) *		RS-232C interface, 20mA current loop output, 3-Relay outputs
				and 1-Control input
	OP-10	(AD-4405-10)		Panel mount kit
				(Panel attachment and load cell input terminal block)

*Only one interface option can be installed at a time, by exchanging with the standard RS-232C interface.

Supplemental accessories (for printer)

Print paper	AX-PP-156-S (10 rolls)
Ink Ribbon	AX--EWRC05-S (5pcs.)

4. Description of Panels and symbols

Page 10

AD-4405 Weighing Indicator

Image 12

A&D AD-4405 manual Accessories and options, Standard accessories, Options, Supplemental accessories for printer

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Accessories and options Standard accessoriesSupplemental accessories for printer Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison Condition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and Condition F22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing Completion Setting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other Functions Key input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HC Using the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output 16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Commands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold Data UFC Commands UFC Command Parameters $DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF RS-422/RS-485, Relay OutputOP-03 TRMCOM Circuit Switching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Current Loop Output Data Format Specifications Analog Input and A/D ConversionDigital Section Interface Dimensions General Memo Memo Memo