Manuals / A&D / Personal Care / Scale

A&D AD-4405 manual Weighing Range Function

Models: AD-4405

1 80

Download 80 pages 1.51 Kb

Page 19

ESC key ..... The key to store the parameters temporarily. Proceed to the Cal 0

display.

Press and hold the ON/OFF key and press the ESC key

No parameters are changed, CanCel is displayed and the calibration mode is finished.

Step18 Press the ON/OFF key to turn the display off.

5.3. Weighing Range Function

The weighing range function can select "single range" or "dual range". Specify each weighing interval (division) for the multi-interval instrument. Each weighing interval is displayed according to a net value or gross value.

Caution

When single range is used, performing this function is not required.

Example 1

The gross display.

Specified parameters:

First range

Range = 50.00kg, division 0.02kg

Second range

Range = 100.00kg (maximum capacity), division 0.1kg

Display

0kg to 50kg :

The first range, division 0.02kg.

50kg to 100kg :

The second range, division 0.1kg.

Division = 0.02kg

Division = 0.1kg

0kg

50kg

100kg Gross

Weighing value

Example 2

The net display using a 40kg tare value.

Specified parameters:

The same parameters as example 1.

Display

-40kg to 50kg :

The first range, division 0.02kg.

50kg to 60kg :

The second range, division 0.1kg.

Division = 0.02kg

Division=0.1kg

-40kg

0kg

50kg 60kg

Net

Gross

Tare value

90kg 100kg

40kg

Weighing value

AD-4405 Weighing Indicator

Page 17

5.3. Weighing Range Function

Image 19

A&D AD-4405 manual Weighing Range Function

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Options Accessories and optionsStandard accessories Supplemental accessories for printer Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format Specifying the Second Range Capacity Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Weighing Range of the First Range Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Clearing Tare Digital Input Preset TareTare Weighing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Output and Condition Setpoint ComparisonDescription of Input parameters and Outputs F22 = 7 Check weighing Weighing Completion F22 = 9 Check weighing 3Loss in weightSimple Batch Start Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Relations to the Other Functions Setting the Hold FunctionsHold Function Display and the Data Output of Hold and Average MT, MZ, HC Key input and command in the hold stateConditions of the Average and Release TARE, ZERO, SETPOINT, Total Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time Bit Format 16.1 SpecificationsRS-232C Interface Circuit and Pin Connection Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Limit/Setpoint Value Commands to Set ParametersSet the Preset Tare Set the Unit Weight for Counting Mode Release the Hold Data Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Start Averaging to Hold UFC Command Parameters UFC Commands PF2,$DT$TM$LF$AN$SP$TL$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF ’$AN$TL$LF$LF Circuit RS-422/RS-485, Relay OutputOP-03TRM COM Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Data Format Current Loop Output Interface SpecificationsAnalog Input and A/D Conversion Digital Section General Dimensions Memo Memo Memo