Simple Batch, F22 = 9 Check weighing 3Loss in weight | A&D AD-4405

F22 = 9 (Check weighing 3:Loss in weight)

Weighing value	Tared Zero	Preset target weight
	Tared Zero

	Final	Tare
	Weighing
	Free fall
		Zero band
Calibrated Zero
Output and Condition		Time
		Time

Relay HI,	1, -Net ] - (Final - Free fall)		OFF					ON		OFF
Relay LO,	3, Gross ¢ Zero band	ON		OFF				ON		OFF

Relay OK*,	2, Gross ] Full	OFF		ON		OFF				ON

*Relay OK output can be changed to OVER or UNDER by setting f24. Triangle 2 is displayed when Gross ] Full regardless of the f24 setting.

OVER/UNDER is judged always and the result is output to the LED and the relay.

10.2.2.Simple Batch

The weighing sequences of simple batch (f22 10,11 or 12) are similar to those of Check weighing (f22 7, 8 or 9) respectively. The differences are listed below.

1	Basically ON/OFF of the relay and the LED are reversed.
2	No judgment other than Zero band and Full before input of the Start signal.
3	The weighing completion condition is set by f23 2x and it is effective after Start.

4The outputs of Preliminary and Free fall are off from weighing completion to the next start.

5 Weighing completion can be output by setting f24 and f25.

6The start signal can be accepted after weighing completion even if the weight is not within the zero band.

7 Over/Under output is set by f23 3x.

Start

Tare, when the Start is input automatically if f23 11.

The READY mark turns off when the Start is input.

Weighing Completion

The weighing completion condition is set by f23 2x.

f23 20 : Either the STOP key is pressed or the Batch stop input is on.

f23 21 : Stable is detected after reaching Final.

Before reaching Final, the STOP key or Batch stop input forces weighing completion even if f23 21.

10.2. Setpoint Comparison

Page 42

AD-4405 Weighing Indicator

Image 44

A&D AD-4405 manual Simple Batch, F22 = 9 Check weighing 3Loss in weight, Start, Weighing Completion

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Accessories and options Standard accessoriesSupplemental accessories for printer Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison LO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and Condition F22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing Completion Returns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other Functions Key input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HC Counting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output 16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Commands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold Data UFC Commands UFC Command Parameters $DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF RS-422/RS-485, Relay OutputOP-03 TRMCOM Circuit Switching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Current Loop Output Data Format Specifications Analog Input and A/D ConversionDigital Section Interface Dimensions General Memo Memo Memo