Introduction | A&D AD-4405 instruction

2.Introduction

The AD-4405 is a weighing indicator that amplifies signals from a load cell, converts it to digital data and displays it as a mass value.

This indicator has the following performance:

Input sensitivity: ......................... 0.25 mV/division.

Maximum display: ...................... 40000 divisions.

Refresh rate of the display: ........ 10 times/second approximately.

Input voltage range: ................... -1 mV ~ +15 mV.

The following standard functions are available:

The HiHi / Hi / OK / Lo / LoLo limit comparison to check a mass value. The setpoint comparison for batching applications.

The counting function for piece counting.

The preset tare function.

There are four code memories to store the above mentioned data.

The accumulation function to totalize these mass values and to count the number of accumulations.

The hold function enables weighing a living animal.

UFC (Universal Flex Coms) function to customize the protocol of the printing format as well as outputting data using the serial interface.

0 - 9 keys enables easy operation, such as setting of comparator values. Built-in calendar clock with backup battery.

There are the following interfaces:

One interface can be installed in the indicator at a time.

An RS-232C serial interface is standard, to communicate with a computer, printer or a remote display. This interface outputs data and can request weight data, enter parameters and control the state of the indicator.

RS-422/485 and 3-Relay Outputs (Option: OP-03)

RS-232C, 3-Relay Outputs and 3-Control Inputs (Option: OP-05)

RS-232C, Current Loop Output, 3-Relay Outputs and 1-Control Input (Option: OP-08)

Analog Output (4-20mA) (Option: OP-07)

There is optional dot matrix impact printer. (OP-06)

The calibration function includes the following functions:

Setting of the minimum division (weighing interval) and the maximum capacity. Zero and span calibration.

The weighing range function of the multi-interval weighing instrument (scale). Digital linearization function.

Gravity compensation function.

2. Introduction

Page 4

AD-4405 Weighing Indicator

Image 6

A&D AD-4405 manual Introduction

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Supplemental accessories for printer Accessories and optionsStandard accessories Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison Condition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and Condition Start F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing Completion Setting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other Functions TARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HC Using the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output Circuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Set the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint Value Start Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold Data UFC Commands UFC Command Parameters ’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LF COM RS-422/RS-485, Relay OutputOP-03TRM Circuit Switching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Current Loop Output Data Format Digital Section SpecificationsAnalog Input and A/D Conversion Interface Dimensions General Memo Memo Memo