Digital Linearization Function | A&D AD-4405 manual

5.3.1.Setting the Division and Range

Consider the following rules to design the weighing range.

Rule 1 Select the division and range of each weighing range so as to fit the following inequality. The first range < the second range

The division of the next weighing range is automatically set larger than the division of the lower weighing range. And the division can change.

Rule 2 When setting the dual range, the upper limit value of the second range becomes the maximum capacity.

Rule 3 Select a resolution smaller than 40000. The resolution is a value that divides the maximum capacity by the minimum division of the first range.

5.4. Digital Linearization Function

Even if the zero and span calibration have been completed, there may still remain a

linearity deviation caused by the performance of the weighing unit. The digital

linearization function can rectify or reduce the linearity deviation using weighing points

during the zero and capacity setting. Up to three weighing points can be specified.

Caution

This function does not improve repeatability or hysteresis.

Use the mass on the condition that lnr 1 < lnr 2 < lnr 3.

Do not press the

ENTER

key while the STABLE mark is off.

Step 1

Check the

Cal 0

display. Press the

MODE

key to display

lnr 0

.

Step 2 Enter the zero point. Refer to “5.2.3. Zero Calibration”.

Step 3

The value of the middle point is displayed after indicating

lnr x. x is 1, 2 or 3.

The triangle mark of the same number(x) is displayed along with the value.

Step 4

Select a middle point.

If you want to cancel the current procedure, press the

ESC

key to finish this

function. Proceed to step 7 and other points are cleared (canceled).

Select a middle point value using the 0 - 9 keys. Proceed to step 5.

Step 5

Place a mass equivalent to the displayed value on the weighing unit. Press the

ENTER

key after the STABLE mark has turned on. Proceed to step 6.

Step 6

If you include a 2nd and 3rd middle point, repeat steps 3, 4, 5 for each.

If you finish this function, proceed to step 7.

Step 7

Perform step 11 of "5.2.4. Span Calibration" immediately.

5.4. Digital Linearization Function

Page 18

AD-4405 Weighing Indicator

Image 20

A&D AD-4405 manual Digital Linearization Function, Setting the Division and Range

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Accessories and options Standard accessoriesSupplemental accessories for printer Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison LO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and Condition F22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing Completion Returns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other Functions Key input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HC Counting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output 16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Commands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold Data UFC Commands UFC Command Parameters $DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF RS-422/RS-485, Relay OutputOP-03 TRMCOM Circuit Switching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Current Loop Output Data Format Specifications Analog Input and A/D ConversionDigital Section Interface Dimensions General Memo Memo Memo