Common Printer and Data Output Items | A&D AD-4405 manual

15. Common Printer and Data Output Items

There are some similar functions and operations for the internal printer and the serial data output (RS-232C, RS-422/485 and the current loop).

Data output / print output mode

Data number (not available the current loop)

Interval data output or print out

			15.1.			Data Output / Print Mode

Description of "Stream Mode" (For data output)
Function					f37 0, f40 0
Operation					The data is output at each sampling (when refreshing the display).
					Use this mode to output data to an external display (The data may not be
					output due to timing of the baud rate and internal sampling rate). If the data

					is to printed by pressing the				PRINT	key on the printer, use the stream mode.
					The serial interface command can not be used at f40 0.
Description of "Manual Print"
Function					f37 1, f40 1, f60 1

Operation					When pressing the		PRINT	key or the external input is set to output or print,
					the stable weighing data is output and/or print just once.
					The serial interface command can be used at f40= 1.
Description of "Auto Print Mode"
					Object	f37 2 or 3, f40 2 or 3, f60 2 or 3,
Operation					When the weight data varies from the "inhibit region for output" to the
					"permission region of output", the stable data is output and/or print just once.
					If you use this mode, set f02 1 ~ 10, but not 0.
					The serial interface command can be used at f40 2 or 3.
					For weighing (and removing) each object and printing the data.


					In case of f37 2, f40 2, f60 2


					"Inhibit region for output" * +5d.						+5d < "permission region of output".
					In case of f37 3, f40 3, f60 3


					-5d * "inhibit region for output" * +5d.
					"Permission region of output" < -5d, +5d < "permission region of output".
									d: division (weighing interval) of the first range.
Description of "Accumulation Data Output/Print"
Function					f37 4, f40 4, f60 4
Operation					When accumulating by manual or automatic, data is output and/or print
					automatically with the accumulated data.
					The serial interface command can be used at f40 4.
AD-4405 Weighing Indicator								Page 53			15. Common Printer and Data Output

Image 55

A&D AD-4405 manual Common Printer and Data Output Items, Data Output / Print Mode

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Options Accessories and optionsStandard accessories Supplemental accessories for printer Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format Specifying the Second Range Capacity Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Weighing Range of the First Range Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Clearing Tare Digital Input Preset TareTare Weighing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode HI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Output and Condition Setpoint ComparisonDescription of Input parameters and Outputs F22 = 7 Check weighing Weighing Completion F22 = 9 Check weighing 3Loss in weightSimple Batch Start Toward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Relations to the Other Functions Setting the Hold FunctionsHold Function Display and the Data Output of Hold and Average MT, MZ, HC Key input and command in the hold stateConditions of the Average and Release TARE, ZERO, SETPOINT, Total Unit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time Bit Format 16.1 SpecificationsRS-232C Interface Circuit and Pin Connection Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Limit/Setpoint Value Commands to Set ParametersSet the Preset Tare Set the Unit Weight for Counting Mode Release the Hold Data Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Start Averaging to Hold UFC Command Parameters UFC Commands PF2,$DT$TM$LF$AN$SP$TL$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF ’$AN$TL$LF$LF Circuit RS-422/RS-485, Relay OutputOP-03TRM COM Switching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Data Format Current Loop Output Interface SpecificationsAnalog Input and A/D Conversion Digital Section General Dimensions Memo Memo Memo