Setting the Parameters of Setpoint Comparison | A&D AD-4405 manual

Toward the Zero band

Preliminary and Free fall output are holding the off state.

Over/Under comparison starts. If f23 30, judgment starts when Free fall turns on. The judgment is not latched and the output is according to the state at the time. The Weighing completion relay is turned on if f24 2. The on time is set by f25. The READY mark is blinking regardless of the settings of f24 and f25.

Start is may be accepted at this state.

Returns to Zero band

Over/Under and Weighing completion output is off.

The READY mark is turned on.

10.2.3.Setting the Parameters of Setpoint Comparison

Refer to "10.1.2. Setting Upper/Lower Limit Values".

The zero band value is set at f26 of the F-Functions, and the value does not belong to a specific code memory, but is used commonly.

Setting Order and Display for Setpoint Comparison and Simple batch

f22	MODE	Display	1	2	3	4	5
7	Setpoint	Setpoint	Final	Free fall	Over	Under
	Comparison	Class	Fi	FF	Hi	Lo
	1	Comparator	OK		HI	LO
		Triangle		1
8	Setpoint	Setpoint	Free fall	Preliminary	Over	Under	Under
	Comparison	Class	Fi	FF	Pr	Hi	Lo
	2	Comparator	OK			HI	LO
		Triangle		1	2
9	Setpoint	Setpoint	Final	Free fall	Full	Over	Under
	Comparison	Class	Fi	FF	Fu	Hi	Lo
	3	Comparator	OK			HI	LO
		Triangle		1	2
10	Simple	Setpoint	Final	Free fall	Over	Under
	Batch 1	Class	Fi	FF	Hi	Lo
		Comparator	OK		HI	LO
		Triangle		1
11	Simple	Setpoint	Final	Free fall	Preliminary	Over	Under
	Batch 2	Class	Fi	FF	Pr	Hi	Lo
		Comparator	OK			HI	LO
		Triangle		1	2
12	Simple	Setpoint	Final	Free fall	Full	Over	Under
	Batch 3	Class	Fi	FF	Fu	Hi	Lo
		Comparator	OK			HI	LO
		Triangle		1	2

AD-4405 Weighing Indicator

Page 43

10.2. Setpoint Comparison

Image 45

A&D AD-4405 manual Setting the Parameters of Setpoint Comparison, Toward the Zero band, Returns to Zero band

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Standard accessories Accessories and optionsSupplemental accessories for printer Options Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format To Get Stabilized Data Specifying the Second Range ResolutionSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Tare Digital Input Preset TareWeighing Tare Clearing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode Condition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode Description of Input parameters and Outputs Setpoint ComparisonF22 = 7 Check weighing Output and Condition Simple Batch F22 = 9 Check weighing 3Loss in weightStart Weighing Completion Setting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Hold Function Setting the Hold FunctionsDisplay and the Data Output of Hold and Average Relations to the Other Functions Conditions of the Average and Release Key input and command in the hold stateTARE, ZERO, SETPOINT, Total MT, MZ, HC Using the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time RS-232C Interface 16.1 SpecificationsCircuit and Pin Connection Bit Format Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Preset Tare Commands to Set ParametersSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands to Set the Data Output/ Print Format UFC Commands for the Hold FunctionStart Averaging to Hold Release the Hold Data UFC Command Parameters UFC Commands SF1,$ID$DN$CR$LF$GR$UT$CR$LF $DL’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF TRM RS-422/RS-485, Relay OutputOP-03COM Circuit Switching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Data Format Current Loop Output Analog Input and A/D Conversion SpecificationsDigital Section Interface General Dimensions Memo Memo Memo