Using the Counting Function | A&D AD-4405 specs

12. Counting Function

This function determines the number of objects in a sample based on the unit weight. The unit weight is stored in one of the code memory data in non-volatile memory, and is not lost even if the AC power supply is disconnected.

12.1. Using the Counting Function

Preparation: Set f07 1 in the F-Functions.

Select a code memory number. Refer to “9.1.1. Using Code Memory”.

Register the unit weigh. Refer to “12.2. Unit Weight Registration”.

Press the MODE key to enter the counting mode. The unit in the display changes to pcs.

In the counting mode, TARE, ZERO, NET/GROSS and other operations are the same as that in the normal weighing mode.

12.2. Unit Weight Registration

There are two methods to register the unit weight. One is to weigh the actual samples for unknown object's unit weight and the other way is by digital input of the unit weight by key or via the serial interface.

The unit weight is one item of the code memory data. Select the code memory number and start the unit weight registration in the weight display or piece count display. The unit weight registration can not be done from the code memory number display.

There is no counting accuracy improvement function by re-calculating the unit weight based on the actual weight.

Weigh Actual Samples

When the unit weight is unknown, prepare some samples to determine the unit weight.

Step 1

Enter the counting mode.

Step 2

Press the

SAMPLE

key to enter the unit weight registration.

5 0

or

5 -

is

displayed and unit pcs blinks. The left side of the display is the number of samples.

The right side of the display indicates the weight, 0

means that the weight is zero

and

-

means that the display is not at zero.

Step 3

Select the number of samples and place the samples specified on the weighing

sensor unit. Using following keys:

0 - 9 key

The key to set the number of samples. Maximum is 9999.

+/- key

The key to select the number of samples, 5, 10, 20, 50,100.

................

The key to set the zero point.

ZERO

key

................

The key to tare. When using a container.

TARE

key

12. Counting Function

Page 46

AD-4405 Weighing Indicator

Image 48

A&D AD-4405 manual Using the Counting Function, Unit Weight Registration

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Accessories and options Standard accessoriesSupplemental accessories for printer Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison Condition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and Condition F22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing Completion Setting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other Functions Key input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HC Using the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output 16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Commands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold Data UFC Commands UFC Command Parameters $DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF RS-422/RS-485, Relay OutputOP-03 TRMCOM Circuit Switching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Current Loop Output Data Format Specifications Analog Input and A/D ConversionDigital Section Interface Dimensions General Memo Memo Memo