Condition formula for Comparison, Hi, Ok, Lo, Ok | A&D AD-4405

There are 3 type of setting values for each comparison.

(1)Set the limit value (upper and lower limit / HiHI, Hi, Lo, LoLo limit).

(2)Set the Target value and an acceptable tolerance (upper and lower) in weight. The limit value is calculated automatically.

(3)Set the Target value and an acceptable tolerance (upper and lower) in percentage of the target weight. The limit value is calculated automatically.

Example. Target = 50kg, Upper limit = 51kg, Lower limit = 48kg

(1)Hi (Upper limit): 51 (kg), Lo (Lower limit): 48 (kg)

(2)TG (Target): 50 (kg), Hi (Upper acceptable tolerance): 1 (kg),

Lo (Lower acceptable tolerance): 2 (kg) not a negative value

(3)TG (Target): 50 (kg), Hi (Upper acceptable tolerance): 2 (% of Target), Lo

(Lower acceptable tolerance): 4 (% of Target) not a negative value

10.1.1.Condition formula for Comparison

Comparison is performed based on the following formula.

Upper/lower comparison

Judge	Condition Formula	Display		Output
HI	Upper limit (Hi limit) value ¢ Displayed value	HI		HI
OK	Lower limit value * Displayed value * Upper limit value	OK		OK
LO	Displayed value ¢ Lower limit (Lo limit) value	LO		LO
5-stage comparison

Judge	Condition Formula	Display		Output
HiHi	HiHi limit value ¢ Displayed value	HI,	2	HI
HI	Upper limit (Hi limit) value ¢ Displayed value	HI		HI, OK
OK	Lower limit value * Displayed value * Upper limit value	OK		OK
LO	Displayed value ¢ Lower limit (Lo limit) value	LO		LO, OK
LoLo	Displayed value ¢ LoLo limit value	LO,	3	LO

The decimal point is not considered. Example: If the upper limit value is 10.0, enter 100. These parameters are stored in non-volatile memory, and are not lost even if the AC power is disconnected or cut off (except code 0 memory).

When the displayed value becomes an overload (positive over), HI (over) is output. When the displayed value becomes an under load (negative over), LO (under) is output.

This function compares the Hi / HiHi limit value first.

This function does not check the relationship between the upper and lower limit values.

AD-4405 Weighing Indicator

Page 39

10.1. Weight Check Mode

Image 41

A&D AD-4405 manual Condition formula for Comparison, Hi, Ok, Lo, Ok

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Verifying Load Cell Output and Input Sensitivity Adjustment of the Load Cell Output Installing an Option Board Front Panel Description Description of Panels and symbols Rear Panel Description Other Displays and Symbols Standard accessories Accessories and optionsSupplemental accessories for printer Options Calibration Items of Calibration Mode Configuring a Weighing Instrument Calibration Procedure Specifying the Range and Unit Specifying the Resolution, Decimal Point Position and Format To Get Stabilized Data Specifying the Second Range ResolutionSpecifying the Weighing Range of the First Range Specifying the Second Range Capacity Span Calibration Zero Calibration Exiting the Calibration Mode Weighing Range Function Digital Linearization Function Setting the Division and Range Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Functions Changing the Function Settings OFF Functions ZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface DD/MM/YY YY/MM/DD MM/DD/YY Print Format CF-Functions Tare Digital Input Preset TareWeighing Tare Clearing Tare Accumulation Preparation and Specifications Display and Operation Parameter Code Memory Using Code Memory Comparison Weight Check Mode LO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode Description of Input parameters and Outputs Setpoint ComparisonF22 = 7 Check weighing Output and Condition Simple Batch F22 = 9 Check weighing 3Loss in weightStart Weighing Completion Returns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Hold Function Setting the Hold FunctionsDisplay and the Data Output of Hold and Average Relations to the Other Functions Conditions of the Average and Release Key input and command in the hold stateTARE, ZERO, SETPOINT, Total MT, MZ, HC Counting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Replacing the Ink Ribbon Installing the Printer Paper Special roll paper Common Printer and Data Output Items 15.1 Data Output / Print Mode Interval Data Output / Print Data Number Interval Data Output / Print output Setting the Interval Time RS-232C Interface 16.1 SpecificationsCircuit and Pin Connection Bit Format Figures Data Format Explanation of Commands Command Format Commands to Request Data Commands to Control the Indicator Changing the Code Memory Changing the Weight Unit Set the Preset Tare Commands to Set ParametersSet the Unit Weight for Counting Mode Set the Limit/Setpoint Value Commands to Set the Data Output/ Print Format UFC Commands for the Hold FunctionStart Averaging to Hold Release the Hold Data UFC Command Parameters UFC Commands SF1,$ID$DN$CR$LF$GR$UT$CR$LF $DL’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LF TRM RS-422/RS-485, Relay OutputOP-03COM Circuit Switching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Data Format Current Loop Output Analog Input and A/D Conversion SpecificationsDigital Section Interface General Dimensions Memo Memo Memo