UFC Commands, UFC Command Parameters | A&D AD-4405 instruction

16.4. UFC Commands

UFC (Universal Flexi Coms) function enables editing the serial data output format or the print out format freely using the serial interface command.

For customizing the print out of the printer or efficient data collection. Output data is not only the indicator’s data/status but also characters at will.

It can output the control code* of the printer. (* depends on the individual printer) There are 2 sets of memories for storing the parameters.

UFC Command Parameters

UFC commands such as SF1, PF1 have many parameters.

One command line can have multiple parameters. The parameters are stored in memory in order.

Multiple UFC commands are acceptable. Parameters are stored next to the last parameter stored by the last UFC command.

Clear all of the data first, if storing a new set of parameters. The parameters in the stored data can not be changed partially.

The various types of parameters and their descriptions are shown below.

Data	Weight, result of comparison, etc.
$CL	Clear previous settings. UFC command parameters can not be
	changed partially.
$WT	Displayed data
$GR	GRoss data
$NT	NeT data
$TR	TaRe data
$HD	Header of Gross/Net/Tare or Preset tare. Refer to CF06.
$UT	Weight UniT
$ST	STable/Unstable
$CP	Result of ComParison
$ID	ID number specified at F06
$DT	Date
$TM	Time
$DN	Data number increments with each output automatically
$CD	CoDe memory number
$AN	Accumulation count
$TL	TotaL weight
$CM	CoMma
$CR	CR code (0Dh)
$LF	LF code (0Ah)
$DE	DElete the last parameter
16.4. UFC Command	Page 64	AD-4405 Weighing Indicator

Image 66

A&D AD-4405 manual UFC Commands, UFC Command Parameters

Contents

Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input Sensitivity Installing an Option Board Description of Panels and symbols Front Panel Description Other Displays and Symbols Rear Panel Description Supplemental accessories for printer Accessories and optionsStandard accessories Options Items of Calibration Mode Calibration Calibration Procedure Configuring a Weighing Instrument Specifying the Resolution, Decimal Point Position and Format Specifying the Range and Unit Specifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range Capacity Zero Calibration Span Calibration Exiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization Function Gravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings Functions Functions OFF ZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YY Print Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing Tare Preparation and Specifications Accumulation Display and Operation Parameter Using Code Memory Code Memory Weight Check Mode Comparison Condition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and Condition Start F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing Completion Setting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other Functions TARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HC Using the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon 15.1 Data Output / Print Mode Common Printer and Data Output Items Data Number Interval Data Output / Print Setting the Interval Time Interval Data Output / Print output Circuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit Format Data Format Figures Command Format Explanation of Commands Commands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code Memory Set the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint Value Start Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold Data UFC Commands UFC Command Parameters ’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LF COM RS-422/RS-485, Relay OutputOP-03TRM Circuit Switching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Current Loop Output Data Format Digital Section SpecificationsAnalog Input and A/D Conversion Interface Dimensions General Memo Memo Memo