Copyright, Warranty | Agilent Technologies Agilent 81130A 400

Notice

Notice

Copyright

1998 Agilent Technologies 1998, 2000. All rights reserved.

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies Inc. as governed by United States and international copyright laws.

Notice

The material contained in this document is subject to change without notice. Agilent Technologies makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Warranty

This Agilent Technologies product has a warranty against defects in material and workmanship for a period of three years from date of shipment. During the warranty period, Agilent Technologies will, at its option, either repair or replace products that prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by Agilent Technologies. The Buyer shall pay Agilent Technologies round-trip travel expenses. For products returned to Agilent Technologies for warranty service, the Buyer shall prepay shipping charges to Agilent Technologies and Agilent Technologies shall pay shipping charges to return the product to the Buyer. However, the Buyer shall pay all shipping charges, duties and taxes for products returned to Agilent Technologies from another country.

4

Image 4

Agilent Technologies Agilent 81130A 400, 660MHz manual Copyright, Warranty

Contents

Reference Guide Front Panel Display and Softkeys Agilent 81130A 400/660 MHz Pulse/Data Generator Reference Guide Warranty Copyright Limitation of Warranty Services and SupportExclusive Remedies Certification Safety Summary Before Applying PowerGeneral Environmental Conditions Ground the Instrument FusesDo Not Operate in an Explosive Atmosphere Do Not Remove the Instrument Cover Safety Symbols Protective earth ground terminal Manuals About this Book Conventions Used in this Book Contents Agilent 81130A Specifications 102103 105 General Programming Aspects GP-IB Interface Bus General Programming Aspects Agilent 81130A Remote Control Programming Recommendations DISPlay OFF OPC? Common Command Summary Status Model Questionable Status Transition Filters Condition RegisterEvent Register Enable Register NTR PTR Status Byte Standard Event Status Group OPERation Status Group QUEStionable Status Group Programming Reference Agilent 81130A Scpi Command Summary Programming Reference DIGital Copy High Hold SOURce ROSCillator STATus OPERation EVENt? KEY Default Values, Standard Settings Parameter RST, Default Values Load TTL TRIGger COUNt PULSes LEVel TERMination SOURce Programming the Instrument Trigger Modes Continuous StartedGated Pulses Burst Pattern Manually Starting and Gating Started Scpi Instrument Command List Armlevterm Armmode Armsens Armsour Instrument with two Output channels installed Output 2 can be used in parallel Use this command to set up a counted loop across one or more To setup an infinite loop over segment 2 to segment Use this command to set up the destination segment See previous example Digpatt DigpattlooplengDigpattprbs –1 Prbs on Output DataSegment Segment 2 to Segment 4 set to all bits set to zero See DIGPATTSEGM1DATA2 #1501011 Restrictions 32, 0, 0, 0 segment 1 = 32, segments 2, 3, and 4 =Be overwritten no undo DIGPATTSEGM1234TYPE12 DIGitalSTIMulusPATTernUPDate Update the hardware with the new pattern data by sending aPattern generating hardware following a DIGSIGN12FORM Disp Query Filetype is always blank. a directory name has filesize =Event Directoryname Only select a directory name within the current directory Filename,A,copyname,ADirectory of the current directory Mmemdel Mmeminit Mmemstorstat OUTP12COMP OFF CORR12EDELay Output signals are the same at the device-under-test–25.0 ns to +25.0 ns CURR12 Execute the SOURceHOLD CURRent command to enable CURR12OFFSet∝A 50 Ω into 50 Ω Amplitude +10 mA 50 Ω into 50 Ω Execute Sourcehold CURRent command to enableLow-level –10 mA 50 Ω into 50 Ω 8V Outputs 50 Ω into short max mA typical0V Outputs 50 Ω into short max mA typical High-level –10.0 mA CURR12LIMSTAT Output limits cannot program the output-levels beyond Hz with engineering prefixes, or MHZ for Megahertz00 MHz Agilent 81131A 1 kHz to 400 MHz Connector as the frequency source Trigsour EXT Use this command to enable either of the SOURceVOLTage orFreqauto Once To 360 constrained by delay and period limits Programming the pulse phase also executes SOURcePULSeHOLDPHAS12 PULSDCYC12 Specified limits 0.1 – 99.9%, depends on Width & Period To 3.00 µs Pulse-delay PHAS2 180DEG PULSHOLD12 PULSDEL12UNITPulsper Programmed by this command. Note that the specified limits Available resolution depend on the selected sourceConnector as the frequency source Trigsour EXT2 Agilent 81131A 2.5 ns to 1 ms Agilent 81132A 1.5 ns to 1 ms PULSTRAN12UNIT PULSTRAN12 Trailing-edge = Leading-edge fixed coupled Agilent 81131A 0.8 ns or 1.6 nsWithin the defined pulse-width PULSTRIG1POS PULSTRIG1MODEPULSTRIG1VOLT To set width as dutycycle use SOURcePULSeDCYCle12 MHz, 2 MHz, 5 MHz or 10 MHz reference signal using Roscextfreq VOLT12 Agilent 81131A 0.10 Vpp to 3.80 VppAgilent 81132A 0.10 Vpp to 2.50 Vpp Execute Execute the SOURceHOLD VOLTage command to enable VOLT12HIGH VOLT12LOW Hardware, this is a software limit +500 mV–500 mV Limits are always enabled/disabled together Scpi Instrument Command List STATusPRESet Long STATusQUEStionableENABle STATusQUEStionableEVENt?STATusQUEStionableCONDition? STATusQUEStionableNTRansition Message are put into the instruments output buffer Replaced with -350meaning Queue overflowOutput example Systkey Scpi Instrument Command List Specified limits Key Description Emptied by *RST and returns the value -1 when empty Systkey 19 sets the instrument to Local mode Systpres Systsec SYSTVERS? Active Separator between the messagesTrigcoun Set by TRIGgerCOUNt. Changes of the number of pulses on BurstChanges on the channels TRIGCOUNPULS1? ⇒ TRIGCOUN? ⇒ Output 1 or Output Triglevterm Command Trigsour Scpi Instrument Command List Temperature 81132AUsed by the instrument Warranted Performance Specifications Declaration of Conformity Agilent 81130A Specifications SafetyPower requirements Maximum Dimensions H x W x D Recalibration period WeightAcoustic Noise Emission Period & Frequency Width Delay100 Compensation for different cable delays DeskewTransition Times Digital Channel Add Main Output Level Specifications External Input External Clock/PLL Reference Input Specifications of EXT INPUT/CLK-IN REF Input 104 Externally Gated Externally StartedGenerate continuous pulses, bursts, or patterns Specification of Trigger Output Output Modes Patterns and Sequences Burst Mode107 Human Interface Overprogramming Help Key Non-Volatile MemoryMemory Card Function Code All checks and display off Programming Times110 Pulse Parameter Definitions Trigger Delay Time Reference PointPulse Period Pulse Width Pulse Delay Interchannel Delay Skew Linearity Transition Time114 Jitter StabilityPulse Levels 115 Settling Time Preshoot, Overshoot, Ringing116 Repeatability 118 Index 119 120 121 Scpi 122 Front Panel Controls