Agilent Technologies J3916A Modify/View Security Values

Local Terminal Configuration

Using the Main Menu

Modify/View Security Values

To configure security values for probe access, you use the Modify/View Security

Val ue s m e nu .

1. On the Main Menu, press 2, Modify/View security values. You see the

Modify/View Security Values menu (Figure 2-4).

2. Press a number to select a field and then type the corresponding values

necessary to configure the probe to operate on your network. See “Access

Security” on page 8 for more information on security.

Allow Packet Press 1 and then type Yes to allow or No to not allow

Capture packet capture.

Allow TFTP Press 2 and then type Yes to allow or No to not allow

Firmware Downloads TFTP firmware downloading.

Modify/View Security Values Menu - Firmware Rev

[1]Allow packet capture Yes

[2]Allow TFTP firmware downloads Yes

[3]Allow Packet Generation Yes

[4]Allow duplicate and changed IP checking Yes

S.Save changes and exit

0.Cancel changes and exit

Figure 2-4: Modify/View Security Values Menu

Contents

Main Consumer Warranty Statement Page iv Operating Restrictions v Notice Safety Information Warning Symbols Used in This Book Conventions Used in this Book NOTE Trademarks Page Page Contents 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Local Terminal Configuration. . . . . . . . . . . . . . . . . . . 15 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 4 Bootp Server Configuration . . . . . . . . . . . . . . . . . . . . 71 5 Probe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 6 Download New Firmware . . . . . . . . . . . . . . . . . . . . . . 97 A Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . 113 Page Figures Page Table s Page Page Introduction Figure 1-1: The Probe Installation and Configuration Overview Local Terminal Configuration and Installation Installation and Bootp Server Configuration Probe Overview NOTE System Overview Page Supported MIBs Management Stations Access Security Table 1-1: Private MIB Access Security Privileges Status LEDs Front Panel LEDs Page Introduction Status LEDs 12 Token-Ring Telemetry Interface Status LED Figure 1-4: Rear Panel LEDs RS-232 Config. Power AUI 10Base-T/100Base-TX Status LEDs Activity HSSI WAN Interface Status LEDs CONFIG Button Included Parts Optional Accessories Page Page Probe Configuration Using a Local Terminal NOTE Page Using the Main Menu NOTE Figure 2-1: Probe Rear Panel NOTE Figure 2-2: Probe Main Menu Modify/View Configuration Values Figure 2-3: Modify/View Configuration Values Menu NOTE Modify/View Security Values Figure 2-4: Modify/View Security Values Menu Modify/View Interface Values NOTE Fast Ethernet Telemetry Interface Configuration Figure 2-5: Modify/View Interface Values Menu (Fast Ethernet) NOTE CAUTION Token-Ring Telemetry Interface Configuration Figure 2-6: Modify/View Interface Values Menu (Token Ring) Page NOTE HSSI WAN Interface Configuration Figure 2-7: Modify/View Interface Values Menu (HSSI WAN) Page Page Display Interface Summary Figure 2-8: Display Interface Summary Modify/View Serial Port Settings Figure 2-9: Modify/View Serial Port Settings Menu Page Page Exiting the Main Menu and Restarting the Probe NOTE Page Installation Selecting a Location NOTE Installing the Probe CAUTION Table Installation Rack or Cabinet Installation Page Wall Installation Page Connecting the Probe Connecting to the Network (Out-of-Band) CAUTION Figure 3-3: Probe Rear Panel (Token-Ring Option shown) Connecting to 10MB/s Ethernet Telemetry Networks NOTE Figure 3-4: Connecting the Probe to a 10MB/s Ethernet Network Connecting to 10Base-T/100Base-TX Telemetry Networks Page Connecting to Token-Ring Telemetry Networks Figure 3-5: Connecting the Probe to a 10Base-T/100Base-T Network CAUTION Figure 3-6: Connecting the Probe Using RJ-45 Connectors NOTE Figure 3-7: Connecting the Probe using a Media Filter Page Figure 3-9: HSSI System Figure 3-10: Close-up of the HSSI Interface WAN Network Ethernet In-Line HSSI Connection Figure 3-11: HSSI Monitor In-Line Connection WAN Network Ethernet NOTE Connecting to the Serial Port (Out-of-Band) Direct Connection Modem Connection Figure 3-12: Probe Direct Connection Install the Management Station Modem Figure 3-13: Probe Modem Connection CAUTION Install the Probes Modem Configure the Management Station and the Probe Page NOTE Data Switch Connection Figure 3-14: Probe Data Switch Connection Starting the Probe NOTE Verifying the Installation Out-of-Band Troubleshooting Ethernet Telemetry Interface CAUTION HSSI Troubleshooting Page Bootp Server Configuration Probe Configuration Using a Bootp Server Item Bootp Server Type HP Sun PC Table 4-1: Minimum Requirements for a Bootp Server Bootp Server Setup on an HP or Sun System NOTE Starting the Bootp Server on an HP or Sun System Page Bootp Server Setup on a PC Using Microsoft LAN Manager 2. The final screen looks like the following: Using Novell NetWare Starting the PC Bootp Server Page Configuring the Bootptab File Bootp Server: Bootptab File Location Table 4-2: Bootp Server Bootptab Files Tag Description Table 4-3: Bootptab File Tags NOTE Server Verification Process Table 4-4: Bootp Process Verification Bootp Server Configuration Configuring the Bootptab File 88 Example Bootptab File Page Page Restarting the Probe Warm Start Probe Operation Restarting the Probe Table 5-1: Probe Data and Parameters Reset by Warm or Cold Start 92 Probe Operation Restarting the Probe Table 5-1: Probe Data and Parameters Reset by Warm or Cold Start (Continued) Cycling Power Selecting the Warm Start Menu Item Figure 5-1: Probe Main Menu Cold Start Pressing the CONFIG Button Twice Selecting the Cold Start Menu Item Page Download New Firmware CAUTION Page Downloading Firmware using an HP-UX Workstation and a Terminal NOTE Install New Download Firmware on an HP-UX Workstation Download Firmware to the Probe CAUTION NOTE Figure 6-1: Probe Main Menu (HP-UX Workstation) CAUTION Figure 6-2: Probe TFTP Download Menu (HP-UX Workstation) Downloading Firmware using a Networked PC and a Terminal Setup TFTP Server for Downloading Download Firmware to the Probe CAUTION NOTE Figure 6-3: Probe Main Menu (Networked PC) CAUTION Figure 6-4: Probe TFTP Download Menu (Networked PC) Xmodem Download of Firmware Figure 6-5: Probe Main Menu (XMODEM) Figure 6-6: Probe XMODEM Download Menu CAUTION NOTE Page Page Cables and Connectors HSSI Connectors and Cables Table A-1: HSSI Interface Cable Pinout HSSI Null Modem Cable Signal Name From Pins Direction To Pins Signal Name Table A-2: HSSI Null Modem Cable Pinout Page Token-Ring Cables Serial Port Interface Cables Cable Function Cable Type Connectors Agilent Product Number Table A-4: Serial Port Interface Cable Cable Connector Pin-Outs The Probes RS-232 Port Pin-Out Table A-5: Probe RS-232 Port Pin-Out NOTE PIN US CCOTT DIN The Probes RS-232 Modem Cable Connectors 25-pin Terminal/PC Cable Connectors 9-pin Terminal/PC Cable Connectors UTP Network Connector Pin-Out STP Network Connector Pin-Out Page Specifications Network Compatibility Network Connection Software Standards Modem Page Probe Memory Allocation NOTE Specifications 129 Parameter 32MB 64MB 128MB Figure B-1: Probe Memory Allocation Page Page Glossary Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Index Symbols Numerics A B D E F H I L M N O P R S T V W X Agilent Technologies, Inc. Offices Asia-Pacific Australia/New Zealand Canada Europe