Field Name Bits Default Description
ExtendIntrToWakeTime 18:16 000b This is used in K8 system to extend the interrupt break event
status. Whenever there is an apic interrupt, this logic will
extend the break event status by the amount of time defined
by this register. This is to avoid potential race condition
between CPU issuing the C1e command and the SB seeing
an interrupt. If CPU tries to enter C state before the extension
time expires, SB will break out from the C state. Each count
represents 2 microsecond increment and it has an uncertainty
of 2 microseconds.
DrqMaskEn 19 0b Setting this bit to 1 will cause the legacy DMA request to be
blocked if the DMA channel has not been initialized properly.
This bit is applicable to ASIC revision A21 and above.
IdeIrqFilterEn 20 0b Setting this bit to 1 will cause narrow pulses (less than several
A-link clocks wide) on the IDE IRQ line to be filtered out. This
means that no interrupt will be generated. This bit is applicable
to ASIC revision A21 and above.
TmrIrqEnhanceDisable 21 0b This bit should be set to 1 for the normal operation of the 8254
timer. This setting is required by ASIC revisions A11, A12, and
A13.
PIC_APIC_coexist 22 0b This bit should be set to 1 if PIC and APIC are to be enabled
at the same time in K8 system. There is no harm done even if
they don’t coexist at the same time.
Reserved 25:23 000b
SataIntMap 28:26 000b SATA interrupt mapping to PCI interrupt
000 - INTA#, 001 - INTB#, 010 - INTC#, 011 - INTD#, 100 -
INTE#, 101 - INTF#, 110 - INTG#, 111 - INTH#
Reserved 31:29 000b
SATA_Cntrl register
MSI Mapping Capability - R - 32 bits - [PCI_Reg: B0h] Field Name Bits Default Description
Capability ID 7:0 08h This is a HyperTransport capability list item.
Capability Pointer 15:8 00h T his is the end of capability list.
MsiEnable 16 0b MSI enable programmable through PCI_Reg: ADh bit 7
Fixed 17 1b The address for mapping MSIs is fixed at
0000_0000_FEEx_xxxxh.
Reserved 26:18 000h
Capability Type 31:27 10101b This is an MSI Mapping Capability block.
MSI Mapping Capability register
PciIntGpio - RW - 16 bits - [PCI_Reg: BCh] Field Name Bits Default Description
PciIntGpioOut 3:0 0h Output data for each PCI INT# GPIO providing bits [7:4] and
[15:12] are enabled
PciIntGpioEnB 7:4 Fh Output enable for each PCI INT# GPIO (active low)
PciIntGpioStatus 11:8 - Input status for each PCI INT# GPIO [Read Only]
PciIntIsGpio 15:12 0h Set to 1 to use PCI interrupt INTH/G/F/E# as GPIO
PciIntGpio register
UsbIntMap - RW - 16 bits - [PCI_Reg: BEh] Field Name Bits Default Description
UsbInt1Map 2:0 000b (OHCI0) UsbInt1 interrupt mapping to PCI interrupt
UsbInt2Map 5:3 001b (OHCI1 & OHCI3) UsbInt2 interrupt mapping to PCI interrupt
Reserved 7:6 00b
UsbInt3Map 10:8 010b (OHCI2 & OHCI4) UsbInt3 interrupt mapping to PCI interrupt
UsbInt4Map 13:11 011b (EHCI) UsbInt4 interrupt mapping to PCI interrupt