Replacing the Timekeeper Battery | AMX NI-3101-SIG instruction

Connections and Wiring

Replacing the Timekeeper Battery

The NI-3101-SIG uses a combination lithium battery and clock crystal package called a Timekeeper. Only one Timekeeper unit is installed within a given NI-3101-SIG. The battery can be expected to have up to 3 years of usable life under very adverse conditions. Actual life is appreciably longer under normal operating conditions. This calculation is based on storing the unit without power in 50° C (120° F) temperature until battery levels are no longer acceptable. The part number for a replacement battery is 57-0032.

To replace the Timekeeper battery:

1.Discharge the static electricity from your body by touching a grounded metal object.

2.Unplug all the connectors from the device.

3.Remove the rear panel from the device, and then disconnect the NXI control cable and remove the Master card.

4.Locate the battery behind the Configuration Port on the circuit board.

5.Carefully slide the battery out of its socket and insert the new battery.

6.Plug the 2-pin 3.5 mm mini-Phoenix PWR (green) connector to reapply power. Wait approximately 1 minute, then remove the PWR connector again.

7.Carefully slide the other battery out of its socket and insert the new battery

8.Re-connect the NXI control cable to the Master card.

9.Replace and secure the rear faceplate using the mounting screws and reconnect all communication connectors.

10.Reconnect the 12 VDC power supply to the respective PWR connector and apply power.

20	NI-3101-SIG Signature Series NetLinx Integrated Controller

Image 26

AMX NI-3101-SIG manual Replacing the Timekeeper Battery

Contents

NI-3101-SIG AMX Limited Warranty and Disclaimer Introduction NetLinx Security within the Web Server NetLinx Security with a Terminal Connection 117 Troubleshooting 167 NetLinx Integrated Master Controller Features NI-3101-SIG FG2105-08 Blue LED bar lights when powered up NI-3101-SIG SpecificationsNI-3101-SIG Specifications MB Flash RS-232/422/485 Ports 1 D notation is used to represent a device number IR ports support data mode at limited baud rates and wiringDistances NI-3101-SIG Specifications Page Structure DEV DevicePortSystem DPSWhere Numberportsystem Installation into an Equipment Rack PRD Mode Settings Program Run Disable PRD modeWorking with the Configuration DIP switch PRD Mode Modes and Front Panel LED Blink Patterns Configuration Port Connections and WiringMode Description Blue White Modes and LED Blink Patterns AXlink Port and LED Off No power, or the controller is not functioning properlyPort Assignments and Functionality Rear Port Assignments are as follows Preparing captive wires Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-3101 @ 900 mA Wiring a power connection Using the 4-pin mini-Phoenix connector for data and power GND AXP/TX AXM/RX RS-232/422/485 Device Port Wiring Specifications DB9 Device Port Connections and WiringRelay Port Connections and Wiring Pin Port +12V 6 5 4 3 2 Input/Output I/O Port Connections and WiringRelay connections IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringPort Wiring Specifications NI-3101-SIG Signal Function Signals Connection Pairing Color Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Port type Description Standard Port Ethernet ports used by the Integrated ControllersEthernet Ports Used by the NetLinx Integrated Controllers On-board Master has a built-in FTP server 21/20 TCP Replacing the Timekeeper Battery Configuration and Firmware Update Master Communication Settings dialog box Communicating with the Master via the Program Port Setting the System Value COM1 Using multiple NetLinx Masters Changing the Device Address of a NetLinx Device Device Addressing dialog changing the device value Axcess Devices use Axcess standards Using the ID Button to Change the Controller’s Device ValueRecommended NetLinx Device numbers 301 Resetting the Factory Default System and Device Values Obtaining the Master’s IP Address using Dhcp Network Addresses dialog for a Dhcp IP Address Configuration and Firmware Update Assigning a Static IP to the NetLinx Master Communications Settings dialog box Communicating with the NI Device via an IP TCP/IP Settings dialog box Master Controller User Name and Password dialog box Verifying the current version of NetLinx Master Firmware Sample NetLinx Workspace window showing OnLine Tree tab Upgrading the On-board Master Firmware via an IP Firmware Kit File usage for NI Controllers After the last component fails to install, click Done Select the NI Master’s Kit file from the Files section FIG Upgrading the NI Controller Firmware via IP Configuration and Firmware Update Configuration and Firmware Update Page NetLinx Security within the Web Server Username and profile Case sensitive NetLinx Security TermsNetLinx Security Terms Accessing an Unsecured Master via an Http Address Default Security Configuration Browser Application Frames Default Security Configuration case-sensitive Account Group Master Firmware Security Access Parameters Telnet Security Web Control Managing WebControl Connections Feature Description Compatible Devices Field Security FeaturesManage WebControl Connection Page Features Internet Security System Level Security Security FeaturesFeature Description System Level Group Level System Level Security Master must provide a valid username and password Configuration/Reset, URL list settings, MasterCommunication settings, and security parameters And/or SSH Ports. SSH version 2 is only supported Setting the system security options for a NetLinx Master Section on page 49 for more detailed field descriptions Administrator group account cannot be deleted or modified Security Group Level Security Icsp AuthenticationYou are logged in as a user with Configuration Access Manage Group Communication settings, and file transfers Configure Group PropertiesIP configuration/Reset, URL list settings, Master Adding a new Group Modifying the properties of an existing Group Deleting an existing Group Manage Users Feature Description Manage UsersSecurity User Level Security To this Configure User PropertiesFeature Description Configure User Properties User Security Details Adding a new User Configure Users PropertiesFeature Description User Security Details Sensitive and must be unique Click the Back button to return to the Manage User Modifying the properties of an existing User System Settings Deleting an existing User Manage System Page Components System Settings Manage SystemFeature Description Online Tree menu Online Tree This button is available from within all Management Feature Description Management menu optionsSystem menu buttons Menus Feature Description Device menu buttons Port menu buttons Manage System System Menu Buttons System Menu Modifying the Date/Time System Menu Controlling/Emulating Devices on the Master System Menu Rebooting the MasterSystem Menu Changing the System Number Select either the Control or Emulate option Control/Emulate dialog Valid Level Data Types and Ranges Minimum Value Maximum Value Manage System Diagnostics Diagnostics dialog showing modify popup Feature Update Remove Description Setting up and removing a Diagnostic FilterDiagnostic Configuration Dialog System/Device/Port Feature Description PresetsNew Preset. Refer to of this section for more information NetLinx Security within the Web Server Manage System Server Setting the Master’s Port ConfigurationsDefault port for each service is listed to the right Server Submenu Options SSH FTP Is determined by the user Modifying the Server Port SettingsServer Port Settings SSH Port FeatureDescriptionEnabled but the value can not be changed Address field of the SSH Client application SSL Server Certificate Creation Procedures Certificate consists of two different Keys From an external source Server Certificate EntriesContained in the certificate on the target Master Desired Server Display SSL Server Certificate Information Server Creating a self-generated SSL Certificate Server Regenerating an SSL Server Certificate Request Server Creating a Request for an SSL Certificate State/province name must be fully spelled out Common Steps for Requesting a Certificate from a CA Communicating with the CA Server Exporting an SSL Certificate Request Export SSL Certificate dialog Server Importing a CA created SSL Certificate Before importing a CA server certificate Device Menu Configuring the Network Settings Manage System Device Menu Buttons DNS Address Network Settings DialogFeature Description IP Address Device Menu Developing a URL List Click the Back button to return to the main URL List dialog Device Menu Changing the Device Number URL List dialog with entries Master section on page 67 for more information Device Menu Running a Diagnostic FilterDevice Menu Controlling or Emulating a device Device Menu Viewing the Log System Settings Manage License Adding a new license Removing a license Manage NetLinx Devices System Settings Manage NetLinx DevicesFeature Clear List Refresh List Description Feature Description Device Listings After a period of time, unable to establish communication Manage NetLinx Devices Binding/Unbinding Explained Manage NetLinx Devices Displaying NDP-capable devicesClick the icon to collapse the particular Master’s listing Manage NetLinx Devices Obtaining NetLinx Device information MAC Address of the Master in FIG System Settings Manage Other Devices Manage Other Devices Feature Description Dynamic Device Discovery linksConfigure Binding Options Must always be User-Defined devices Reboot, the selection is cleared This selection is a one-time occurrence. Upon the next Deleted via the Purge Bound Modules on Reset selection What is Dynamic Device Discovery? Dynamic Device Discovery Concepts Manage Other Devices Manage Device Bindings PROGRAMNAME=DDD Configuring application-defined devicesWhat are Application Devices and their association status? Defineconstant Definetype Definevariable Manage Device Bindings NetLinx Security within the Web Server Manage Other Devices Menu Viewing Discovered Devices View Discovered Devices Module Properties displayed via a mouse-over popup dialog Amplifier DocumentCamera SlideProjector AudioConferencer SwitcherSDK-Class Types To configure a Static application interface How do I write a program that uses Dynamic Device Discovery How do I configure a Run-time installation Accessing an SSL-Enabled Master via an IP Address Security Alert and Certificate popups Certificate Import Wizard Using your NetLinx Master to control the G4 panel WebControl VNC installation and Password entry screens What to do when a Certificate Expires Connection Details dialog User has access to the Icsp communication functionality NetLinx Security FeaturesNetLinx Security Features Setup security Access Initial Setup via a Terminal ConnectionAccessing the Security configuration options Logout Close NetLinx Security with a Terminal Connection Or Enter to return to previous menu Security Options EnabledSelect to change current security option Option 2 Display system security options for NetLinx Master CommandItems in the Security Options Menu are described below Option 3 Add user Option 4 Edit User Edit User Menu Select to change current access right Command DescriptionPassword from that point forward Edit User Menu Access Rights Menu Option 5 Delete user Press Enter to display the following Edit Group menu Option 6 Show the list of authorized usersOption 7 Add Group User1 Press Enter to return to the Edit Group menuPath Results.txt Or Enter to return to previous menu Set Rights Select from the following list Administrator GroupOption 8 Edit Group Option 9 Delete Group Option 11 Set Telnet Timeout in secondsSpecify Telnet Timeout in seconds Option 10 Show List of Authorized Groups Option 13 Make changes permanent by saving to flash Option 12 Display Telnet Timeout in secondsTelnet Timeout is 10 seconds Main Security Menu Main Security MenuMain Security menu is described below Set system security options for Group Group administrator Rights All Reset DatabaseAdministrator only function Security Options FTP Security Enabled Help menu Help Menu Options NAME,STRING SET Date NAME,COMMANDSET Icsp TCP Timeout SET DNS DPS Logging Into a Session Help Security Setup SecurityLogout Page Converting Axcess Code to NetLinx Code Master SendCommandsMaster SendCommands Clock G4WC ClockcommandsSendcommand 010,~IGNOREEXTERNALCLOCKCOMMANDS Used to determine each unique listing Master IP Local Port SendCommands Master IP Local Port SendCommandsUsing the ID Button Udpsendto DevicePortSystem DPS Configuration Port CommandsPC COM Port Communication Settings NI-2x00 Port Assignments Echo OFF Configuration Port CommandsDate Echo on MSG on or MSG OFF GET Ethernet ModePort On DPS, NAME, Chan OFF DPS, or NameChan Ping IP Address PWD Name,CommandPulse DPS, or Name Name,String Master-to-Master systems Entering N no cancels the operationPrompts you to enter the new date for the Master Rent Java memory heap size as measured in Megabytes. This Subnet Mask, and Gateway IP Address Enter Y yes to approve/store the information into the Master Set queue size Use caution when adjusting these valuesSET Queue Size Set Queue Size Menu SET UPD BC Rate Displays a list of any combined devices Example Show BuffersEach queue Example Displays a list of all devices present on the bus Example Master logs all internal messages and keeps the most recent Show LOGDisplays the log of messages stored in the Masters memory If end is not entered, the last 20 messages will be shown Show MAX Buffers Lists all active TCP/IP connections Example Show SystemSystems listed are in numerical order Example Displays the current time on the Master Example Linux Telnet client ESC Pass CodesWindowsTM client programs Escape Pass Codes RS232/422/485 Ports Channels LED Disable/Enable SendCommandsLED SendCommands RS232/422/485 ports are Ports These examples DEV = device RS-232/422/485 SendCommandsRS-232/422/485 SendCommands Hson GET BaudHsoff Rxclr Txclr SET BaudTset Baud Xoff XON RS-232/422/485 SendString Escape SequencesRS-232/422/485 SendString Escape Sequences IR / Serial Ports Channels Command Description 27,20,1IR / Serial Ports Channels Sendstring DEV,27,20,1 Caroff IR/Serial SendCommandsIR/Serial SendCommands Caron Cton GET ModeCtof Iroff PON PODPOF Meters for the IR Ports PtofPton SET IO Link Sendcommand IR1, SP,25 SET ModeSendcommand IR1,SET Mode IR Short cable length 10 feet Sendcommand IR1,XCH Sendcommand DEV,XCHM extended channel modeSendcommand IR1,XCHM Xchm GET Input Input/Output SendCommandsSendCommands SET Input Troubleshooting Information TCP/IP Page It’s Your World Take Control