Declaration of CE Conformity | B&K 8510 instruction


				Declaration of CE Conformity
				according to EEC directives and NF EN 45014 norm


		Responsible Party			Alternate Manufacturing Site
Manufacturer’s Name:		B&K Precision Corporation			B&K China 1235
Manufacture’s Address:		22820 Savi Ranch Pkwy.
		Yorba Linda, CA 92887-4610
		USA
Declares that the below mentioned product
Product Name:	Electronic Load
Part Numbers:	8510

complies with the essential requirements of the following applicable European Directives:

Low Voltage Directive 73/23/EEC (19.02.73) amended by 93/68/EEC (22.07.93) Electromagnetic Compatibility (EMC) 89/336/EEC (03.05.88) amended by 92/68/EEC (22.07.93)

and conforms with the following product standards:

LVD	EN 61010-1:2001
EMC	EN 61326:1997
	EN 55011	EN 61000-3-2	EN 61000-3-3
	EN 61000-4-2	EN 61000-4-3	EN 61000-4-4
	EN 61000-4-5	EN 61000-4-6	EN 61000-4-11

This Declaration of Conformity applies to above listed products place on the EU market after:

June 1, 2006

Date	Victor Tolan
	President

Image 56

B&K 8510 instruction manual Declaration of CE Conformity

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Quick Reference Front Panel Rear Panel Front Panel Display Immediate Action Keys Front Panel MenusKey Pad Tran POWER-ON Recall Menu Operation ADC Update Rate High Lowdefault Options and Accessories General InformationDocument Orientation Getting Started Map Features and Capabilities AccessoriesDescription Front Panel Controls Constant Resistance CR Mode Constant Voltage CV ModeRemote Programming Operating Modes Continuous Constant Power CW ModeTransient Operation Pulse Trigger ModeList Operation Short On/Off Triggered OperationInput Control Protection Features Input On/OffOperation Range Over Voltage Over Power Over TemperaturePin trigger and remote sensing connectors Remote Sense Function and Trigger Function Saving and Recalling Settings Wiring diagram for remote sense Battery Testing Operation Von/Voff Operation Action for set Von/Voff value Location InstallationInspection Power Cord Outline DiagramBench Operation Input Connections Checkout Procedure Turn-On CheckoutIntroduction Trigger and Remote Sensing Connections Front Panel Operation Case of TroubleDisplay Front Panel Display Power Set set up a constant current from 0 to Max currentExample Function keys Set set up a constant power from 0 to Max power Set set up a constant resistance from 0.1Ω to 4000ΩPOWER=*.***W 000V Transition Testing Operation Set set up a constant voltage from 1.5V to Max voltageOn/Off input setting Shift + Store Pulse Transient Operation Transition Parameter SettingContinuous Transient Operation Toggled Transient Operation Steps List Operation Quick Recall Function Automatic Testing Function of Electronic LoadEdit the Testing File Enter Automatic Testing Setting the Resolution and number of decimal points Specifications Range Accuracy Resolution Remote Operation Mode Communication cableIT-E131 RS232 Communication cable IT-E132 USB Communication cable IT-E132 communication Communication between electronic load and PCFrame Format 2AH Selecting the Remote control mode（20H） Communication Protocol Selecting the input on/off state （21H） Setting / Reading max input voltage（22H/23H）Setting / Reading the max input current .（24H/25H） Setting / Reading max input power（26H/27H） Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CC mode current value（2AH/2BH）Setting / Reading CV mode voltage value.（2CH/2DH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting /Reading the list repeat mode CH/3DH Setting / Reading the number of list steps EH/3FH Setting / Reading List file name 48H/49H Setting / Reading timer value of for Load on 50H/51H） Save / Get list file in appointed area. CH/4DH Selecting / Reading trigger source H/59H Setting communication address 54HEnable/Disable Local control mode H Sending a trigger signal to trigging the electronic load AH Reading input voltage, current, power and relative state FH Enter the calibration mode（60H） BIT Getting the calibration mode state（61H） Calibrate voltage value（62H） Store the calibration data to EEPROM（66H） Setting / Reading calibration information（67H/68H）Calibrate current value（64H） Reading information in bar code 6BH Restore the factory default calibration data（69H）For example： Setting information of bar code（6CH） Service Information Limited One-Year Warranty Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA