Toggled Transient Operation, Steps | B&K 8510 manual

For example: When load receiving one trigger signal, it will switch to 10A current value, and taking 10mS to return the current value of 5A.

10A
5A	TWD	TWD
	10ms	10ms
	TRIG	TRIG
	Pulsed Transient Operation

Action

1.	Select the operation mode (CC,CV,CR or CP), and set a proper value, press					On/Off to turn off the load input.
2. Press		Shift	+	S-Tran	, set LEVER A=5A, LEVER B=10A, WIDTH B=10mS. Transition mode now is
CONTINOUS.
3.	Press ▼ till >PULSE.
4.	Press	Enter	, set transient mode is PULSE.
5.	Press	Shift	+	Tran	to activate the transient mode.
6.	Press	Shift	+ Trigger		to start another pulse. Press Shift + Trigger	, get more pulse.
7.	Press	Shift	+	Tran	again to stop the transient operation.

8. Press On/Off , the input of load is powered on.

.

Toggled Transient Operation

In this mode, after transition operation start, Load could change the input between the main level and the transient level when toggled transient operation is in effect.

For example:

When Load receives one trigger signal, Load current will switch between 5A and 10A.

10A
5A
TRG	TRG
Toggled Transient Operation

Steps

1. Press	Shift	+ S-Tran , Setting LEVER A=5A, LEVER B=10A, transition mode is TOGGLED.
2. Press	Shift	+ Tran to activate the transient mode.

30

Image 30

B&K 8510 instruction manual Toggled Transient Operation, Steps

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Quick Reference Front Panel Rear Panel Front Panel Display Key Pad Immediate Action KeysFront Panel Menus Tran POWER-ON Recall Menu Operation ADC Update Rate High Lowdefault Document Orientation Options and AccessoriesGeneral Information Getting Started Map Description Features and CapabilitiesAccessories Front Panel Controls Remote Programming Constant Resistance CR ModeConstant Voltage CV Mode Operating Modes Constant Power CW Mode Transient OperationContinuous Trigger Mode List OperationPulse Triggered Operation Input ControlShort On/Off Operation Range Protection FeaturesInput On/Off Over Voltage Pin trigger and remote sensing connectors Over PowerOver Temperature Remote Sense Function and Trigger Function Saving and Recalling Settings Wiring diagram for remote sense Battery Testing Operation Von/Voff Operation Action for set Von/Voff value Installation InspectionLocation Bench Operation Power CordOutline Diagram Input Connections Introduction Checkout ProcedureTurn-On Checkout Trigger and Remote Sensing Connections Display Front Panel OperationCase of Trouble Front Panel Display Example PowerSet set up a constant current from 0 to Max current Function keys POWER=*.***W Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω 000V On/Off input setting Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage Shift + Store Transition Parameter Setting Continuous Transient OperationPulse Transient Operation Toggled Transient Operation Steps List Operation Automatic Testing Function of Electronic Load Edit the Testing FileQuick Recall Function Enter Automatic Testing Setting the Resolution and number of decimal points Specifications Range Accuracy Resolution IT-E131 RS232 Communication cable Remote Operation ModeCommunication cable IT-E132 USB Communication cable Communication between electronic load and PC Frame FormatIT-E132 communication 2AH Selecting the Remote control mode（20H） Communication Protocol Setting / Reading max input voltage（22H/23H） Setting / Reading the max input current .（24H/25H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CC mode current value（2AH/2BH） Setting / Reading CV mode voltage value.（2CH/2DH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting /Reading the list repeat mode CH/3DH Setting / Reading the number of list steps EH/3FH Setting / Reading List file name 48H/49H Setting / Reading timer value of for Load on 50H/51H） Save / Get list file in appointed area. CH/4DH Setting communication address 54H Enable/Disable Local control mode HSelecting / Reading trigger source H/59H Sending a trigger signal to trigging the electronic load AH Reading input voltage, current, power and relative state FH Enter the calibration mode（60H） BIT Getting the calibration mode state（61H） Calibrate voltage value（62H） Setting / Reading calibration information（67H/68H） Calibrate current value（64H）Store the calibration data to EEPROM（66H） Restore the factory default calibration data（69H） For example：Reading information in bar code 6BH Setting information of bar code（6CH） Service Information Limited One-Year Warranty Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA