Bench Operation, Input Connections, Power Cord | B&K 8510 specs

Outline Diagram

Unit (mm)

Bench Operation

A fan cools the electronic load by drawing air through the button and sides and exhausting it out the back. Minimum clearances for bench operation are 25 mm along the sides.

CAUTION

Do not block the fan exhaust at the rear of the Load.

Input Connections

Power Cord

Connect the power cord to the IEC 320 connector on the rear of the unit.

WARNING

SHOCK HAZARD: the power cord provides a chassis ground through a third conductor. Be certain that your power outlet is of the three-conductor type with the correct pin connected to earth ground.

NOTE

The detachable power cord may be used as an emergency disconnecting device. Removing the power cord from the ac input connector will disconnect ac input power to the unit.

23

Image 23

B&K 8510 instruction manual Bench Operation, Input Connections, Power Cord, Outline Diagram

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Front Panel Quick Reference Front Panel Display Rear Panel Tran Immediate Action KeysFront Panel Menus Key Pad Menu Operation POWER-ON Recall ADC Update Rate High Lowdefault Getting Started Map Options and AccessoriesGeneral Information Document Orientation Front Panel Controls Features and CapabilitiesAccessories Description Operating Modes Constant Resistance CR ModeConstant Voltage CV Mode Remote Programming Continuous Constant Power CW ModeTransient Operation Pulse Trigger ModeList Operation Short On/Off Triggered OperationInput Control Over Voltage Protection FeaturesInput On/Off Operation Range Remote Sense Function and Trigger Function Over PowerOver Temperature Pin trigger and remote sensing connectors Wiring diagram for remote sense Saving and Recalling Settings Operation Battery Testing Action for set Von/Voff value Von/Voff Operation Location InstallationInspection Input Connections Power CordOutline Diagram Bench Operation Trigger and Remote Sensing Connections Checkout ProcedureTurn-On Checkout Introduction Front Panel Display Front Panel OperationCase of Trouble Display Function keys PowerSet set up a constant current from 0 to Max current Example 000V Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω POWER=*.***W Shift + Store Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage On/Off input setting Pulse Transient Operation Transition Parameter SettingContinuous Transient Operation Steps Toggled Transient Operation List Operation Quick Recall Function Automatic Testing Function of Electronic LoadEdit the Testing File Enter Setting the Resolution and number of decimal points Automatic Testing Range Accuracy Resolution Specifications IT-E132 USB Communication cable Remote Operation ModeCommunication cable IT-E131 RS232 Communication cable IT-E132 communication Communication between electronic load and PCFrame Format 2AH Communication Protocol Selecting the Remote control mode（20H） Selecting the input on/off state （21H） Setting / Reading max input voltage（22H/23H）Setting / Reading the max input current .（24H/25H） Setting / Reading max input power（26H/27H） Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CC mode current value（2AH/2BH）Setting / Reading CV mode voltage value.（2CH/2DH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting / Reading the number of list steps EH/3FH Setting /Reading the list repeat mode CH/3DH Setting / Reading List file name 48H/49H Save / Get list file in appointed area. CH/4DH Setting / Reading timer value of for Load on 50H/51H） Selecting / Reading trigger source H/59H Setting communication address 54HEnable/Disable Local control mode H Reading input voltage, current, power and relative state FH Sending a trigger signal to trigging the electronic load AH BIT Enter the calibration mode（60H） Calibrate voltage value（62H） Getting the calibration mode state（61H） Store the calibration data to EEPROM（66H） Setting / Reading calibration information（67H/68H）Calibrate current value（64H） Reading information in bar code 6BH Restore the factory default calibration data（69H）For example： Setting information of bar code（6CH） Limited One-Year Warranty Service Information Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA