Quick Reference, Front Panel | B&K 8510 instruction

Quick Reference

The Front Panel

1

2

3

4

5

6

1

2

3

4

5

6

16-character display shows voltage and current measurements. Rotary knob

Power switch ON/OFF

Entry keys:（numeric keys）

Enter values.

Increasing or decreasing the setup values. Menu commands.

Keypad: Enable/disable input.

Setup the current, resistance and voltage modes. Set and reset protection functions.

Scroll through front panel. Input terminals.

Note: Each terminal is able to sink 120A, the maximum current supported by the instrument. Either one of the 2 negative or 2 positive terminals can be used, it is not necessary to double up on the wires when driving a high current.

6

Image 6

B&K 8510 instruction manual Quick Reference, Front Panel

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Quick Reference Front Panel Rear Panel Front Panel Display Key Pad Immediate Action KeysFront Panel Menus Tran POWER-ON Recall Menu Operation ADC Update Rate High Lowdefault Document Orientation Options and AccessoriesGeneral Information Getting Started Map Description Features and CapabilitiesAccessories Front Panel Controls Remote Programming Constant Resistance CR ModeConstant Voltage CV Mode Operating Modes Constant Power CW Mode Transient OperationContinuous Trigger Mode List OperationPulse Triggered Operation Input ControlShort On/Off Operation Range Protection FeaturesInput On/Off Over Voltage Pin trigger and remote sensing connectors Over PowerOver Temperature Remote Sense Function and Trigger Function Saving and Recalling Settings Wiring diagram for remote sense Battery Testing Operation Von/Voff Operation Action for set Von/Voff value Installation InspectionLocation Bench Operation Power CordOutline Diagram Input Connections Introduction Checkout ProcedureTurn-On Checkout Trigger and Remote Sensing Connections Display Front Panel OperationCase of Trouble Front Panel Display Example PowerSet set up a constant current from 0 to Max current Function keys POWER=*.***W Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω 000V On/Off input setting Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage Shift + Store Transition Parameter Setting Continuous Transient OperationPulse Transient Operation Toggled Transient Operation Steps List Operation Automatic Testing Function of Electronic Load Edit the Testing FileQuick Recall Function Enter Automatic Testing Setting the Resolution and number of decimal points Specifications Range Accuracy Resolution IT-E131 RS232 Communication cable Remote Operation ModeCommunication cable IT-E132 USB Communication cable Communication between electronic load and PC Frame FormatIT-E132 communication 2AH Selecting the Remote control mode（20H） Communication Protocol Setting / Reading max input voltage（22H/23H） Setting / Reading the max input current .（24H/25H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CC mode current value（2AH/2BH） Setting / Reading CV mode voltage value.（2CH/2DH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting /Reading the list repeat mode CH/3DH Setting / Reading the number of list steps EH/3FH Setting / Reading List file name 48H/49H Setting / Reading timer value of for Load on 50H/51H） Save / Get list file in appointed area. CH/4DH Setting communication address 54H Enable/Disable Local control mode HSelecting / Reading trigger source H/59H Sending a trigger signal to trigging the electronic load AH Reading input voltage, current, power and relative state FH Enter the calibration mode（60H） BIT Getting the calibration mode state（61H） Calibrate voltage value（62H） Setting / Reading calibration information（67H/68H） Calibrate current value（64H）Store the calibration data to EEPROM（66H） Restore the factory default calibration data（69H） For example：Reading information in bar code 6BH Setting information of bar code（6CH） Service Information Limited One-Year Warranty Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA