Automatic Testing | B&K 8510 guide

15)Repeat 9)～14), and set the other process step by step as follows:

A.CONST CURRENT,0A,SHORT OFF, READ BACK V, 5.9V, 6.4V,1S

B.CONST VOLTAGE, 5V, SHORT OFF,READ BACK A, 0.205A, 0.245A,1S

C.CONST VOLTAGE, 3V, SHORT OFF, READ BACK A, 0.205A,0.245A,1S

D.CONST VOLTAGE, 2V,SHORT OFF, READ BACK A, 0.205A,0.245A, 1S

E.CONST CURRENT, 0A, SHORT ON, READ BACK A,0A,0.245A, 1S

16)VFD displays SHORT TEST FILE*, which requests saving the files edited to EEPROM, automatically testing files and LIST files use a common memory area, and the area can contain 8 groups of automatic testing files for

next usage. Here, the testing file could be saved in the first group, press 1 and press Enter to confirm.

17) When the edition of automatic testing file is finished, press Enter two times to back the menu.

Taking out the Testing File Rapidly

1)	Press	Shift	+ Menu to enter into menu, VFD displays>CONFIG
2) Press▼ and move the menu to>LIST SET
3) Press		Enter	to enter into submenu, VFD displays>MODE SET
4)	Press▼ and move the menu to>CALL TEST FILE
5)	Press	Enter	and recall the file edited

Automatic Testing

After editing the automatic testing file, the automatic testing could be carried out by the below steps.

1) Press	Shift	+ I-set	to enter into automatic testing, VFD displays the name of current file: NAME: TEST
FILE1
2) Press	Enter	to observe the voltage and current we inputted, and also can observe the step number of testing.
3) Press	Shift	+ Trigger	and begin to operate, when the automatic testing is pause (the current prolong time of
one step is 25.5S), press			Shift + Trigger also can make the testing continue.

4)When the automatic testing is finished, the buzzer will hint by tweet (buzzer), VFD reads the result of testing. If the testing passed, VFD reads PASS, or reads FAULT. Press▲、▼ also to observe the numerical value and result of every step.

5)Press ESC to back the automatic testing.

Setting the Resolution and number of decimal points

By selecting the low range and high range, you can measure the voltage and current more precisely.

34

Image 34

B&K 8510 instruction manual Automatic Testing, Setting the Resolution and number of decimal points

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Quick Reference Front Panel Rear Panel Front Panel Display Key Pad Immediate Action KeysFront Panel Menus Tran POWER-ON Recall Menu Operation ADC Update Rate High Lowdefault Document Orientation Options and AccessoriesGeneral Information Getting Started Map Description Features and CapabilitiesAccessories Front Panel Controls Remote Programming Constant Resistance CR ModeConstant Voltage CV Mode Operating Modes Transient Operation Constant Power CW ModeContinuous List Operation Trigger ModePulse Input Control Triggered OperationShort On/Off Operation Range Protection FeaturesInput On/Off Over Voltage Pin trigger and remote sensing connectors Over PowerOver Temperature Remote Sense Function and Trigger Function Saving and Recalling Settings Wiring diagram for remote sense Battery Testing Operation Von/Voff Operation Action for set Von/Voff value Inspection InstallationLocation Bench Operation Power CordOutline Diagram Input Connections Introduction Checkout ProcedureTurn-On Checkout Trigger and Remote Sensing Connections Display Front Panel OperationCase of Trouble Front Panel Display Example PowerSet set up a constant current from 0 to Max current Function keys POWER=*.***W Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω 000V On/Off input setting Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage Shift + Store Continuous Transient Operation Transition Parameter SettingPulse Transient Operation Toggled Transient Operation Steps List Operation Edit the Testing File Automatic Testing Function of Electronic LoadQuick Recall Function Enter Automatic Testing Setting the Resolution and number of decimal points Specifications Range Accuracy Resolution IT-E131 RS232 Communication cable Remote Operation ModeCommunication cable IT-E132 USB Communication cable Frame Format Communication between electronic load and PCIT-E132 communication 2AH Selecting the Remote control mode（20H） Communication Protocol Setting / Reading the max input current .（24H/25H） Setting / Reading max input voltage（22H/23H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CV mode voltage value.（2CH/2DH） Setting / Reading CC mode current value（2AH/2BH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting /Reading the list repeat mode CH/3DH Setting / Reading the number of list steps EH/3FH Setting / Reading List file name 48H/49H Setting / Reading timer value of for Load on 50H/51H） Save / Get list file in appointed area. CH/4DH Enable/Disable Local control mode H Setting communication address 54HSelecting / Reading trigger source H/59H Sending a trigger signal to trigging the electronic load AH Reading input voltage, current, power and relative state FH Enter the calibration mode（60H） BIT Getting the calibration mode state（61H） Calibrate voltage value（62H） Calibrate current value（64H） Setting / Reading calibration information（67H/68H）Store the calibration data to EEPROM（66H） For example： Restore the factory default calibration data（69H）Reading information in bar code 6BH Setting information of bar code（6CH） Service Information Limited One-Year Warranty Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA