Von/Voff Operation, Action for set Von/Voff value | B&K 8510

to confirm

to confirm

VBattery Voltage

Min voltage

t

ILoad Sink Current

t

Von/Voff Operation

You can set voltage value Von/Voff to control the input state on/off for electronic load. When the input voltage reaches the Von value, the load’s input state is on. When the input voltage reaches the Voff value, the load’s input state is off.

Action for set Von/Voff value:

（1） Press Shift + Menu into menu

（2） VFD displays >CONFIG, presskey to choose >SYSTEM SET, press Enter to confirm

（3） VFD displays >MAX CURRENT SET, presskey to choose>VOLTAGE ON SET, press Enter key to

confirm

（4） VFD displays >VOLT.ON=0.00V, press numeric keys to set Von value (0.1V to max voltage value), press Enter

（5） Presskey to choose >VOLTAGE OFF SET, press Enter to confirm

（6） VFD displays >VOLT.OFF=0.00V, press numeric keys to set Voff value (0V to max voltage value), press Enter

21

Image 21

B&K 8510 instruction manual Von/Voff Operation, Action for set Von/Voff value

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Front Panel Quick Reference Front Panel Display Rear Panel Front Panel Menus Immediate Action KeysKey Pad Tran Menu Operation POWER-ON Recall ADC Update Rate High Lowdefault General Information Options and AccessoriesDocument Orientation Getting Started Map Accessories Features and CapabilitiesDescription Front Panel Controls Constant Voltage CV Mode Constant Resistance CR ModeRemote Programming Operating Modes Constant Power CW Mode Transient OperationContinuous Trigger Mode List OperationPulse Triggered Operation Input ControlShort On/Off Input On/Off Protection FeaturesOperation Range Over Voltage Over Temperature Over PowerPin trigger and remote sensing connectors Remote Sense Function and Trigger Function Wiring diagram for remote sense Saving and Recalling Settings Operation Battery Testing Action for set Von/Voff value Von/Voff Operation Installation InspectionLocation Outline Diagram Power CordBench Operation Input Connections Turn-On Checkout Checkout ProcedureIntroduction Trigger and Remote Sensing Connections Case of Trouble Front Panel OperationDisplay Front Panel Display Set set up a constant current from 0 to Max current PowerExample Function keys Set set up a constant resistance from 0.1Ω to 4000Ω Set set up a constant power from 0 to Max powerPOWER=*.***W 000V Set set up a constant voltage from 1.5V to Max voltage Transition Testing OperationOn/Off input setting Shift + Store Transition Parameter Setting Continuous Transient OperationPulse Transient Operation Steps Toggled Transient Operation List Operation Automatic Testing Function of Electronic Load Edit the Testing FileQuick Recall Function Enter Setting the Resolution and number of decimal points Automatic Testing Range Accuracy Resolution Specifications Communication cable Remote Operation ModeIT-E131 RS232 Communication cable IT-E132 USB Communication cable Communication between electronic load and PC Frame FormatIT-E132 communication 2AH Communication Protocol Selecting the Remote control mode（20H） Setting / Reading max input voltage（22H/23H） Setting / Reading the max input current .（24H/25H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CC mode current value（2AH/2BH） Setting / Reading CV mode voltage value.（2CH/2DH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting / Reading the number of list steps EH/3FH Setting /Reading the list repeat mode CH/3DH Setting / Reading List file name 48H/49H Save / Get list file in appointed area. CH/4DH Setting / Reading timer value of for Load on 50H/51H） Setting communication address 54H Enable/Disable Local control mode HSelecting / Reading trigger source H/59H Reading input voltage, current, power and relative state FH Sending a trigger signal to trigging the electronic load AH BIT Enter the calibration mode（60H） Calibrate voltage value（62H） Getting the calibration mode state（61H） Setting / Reading calibration information（67H/68H） Calibrate current value（64H）Store the calibration data to EEPROM（66H） Restore the factory default calibration data（69H） For example：Reading information in bar code 6BH Setting information of bar code（6CH） Limited One-Year Warranty Service Information Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA