Remote Programming, Operating Modes | B&K 8510 specs

Remote Programming

The electronic load may be remotely programmed from the computer via the IT-E131 isolated communication cable.

Operating Modes

The four modes of operation are:

1:Constant current (CC).

2:Constant voltage (CV).

3:Constant resistance (CR).

4:Constant power (CW)

Constant Current（CC）Mode

In this mode, the electronic load will sink a current in accordance with the programmed value regardless of the input voltage. CC mode can be set with front panel keys. The CC mode parameters are discussed in the following paragraphs.

I

CURRENT

LOADSETTING

CURRENT

LOAD INPUT	V
VOLTAGE

CONSTANTCURRENT MODE

Constant Resistance (CR) Mode

In this mode, the module will sink a current linearly proportional to the input voltage in accordance with the programmed resistance. The CR mode can be set at the front panel. The CR mode parameters are described in the following paragraph.

I
LOAD	SLOPE
CURRENT	RESISTANCE
	SETTING
LOAD INPUT	V
VOLTAGE

CONSTANT RESISTANCE MODE

Constant Voltage (CV) Mode

In this mode, the electronic load will attempt to sink enough current to control the source voltage to the programmed value. The module acts as a shunt voltage regulator when operating in the CV mode. The CV mode can be set at the front panel. The CV mode parameters are described in the following paragraphs.

13

Image 13

B&K 8510 instruction manual Remote Programming, Operating Modes, Constant Current（CC）Mode, Constant Resistance CR Mode

Contents

Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Front Panel Quick Reference Front Panel Display Rear Panel Front Panel Menus Immediate Action KeysKey Pad Tran Menu Operation POWER-ON Recall ADC Update Rate High Lowdefault General Information Options and AccessoriesDocument Orientation Getting Started Map Accessories Features and CapabilitiesDescription Front Panel Controls Constant Voltage CV Mode Constant Resistance CR ModeRemote Programming Operating Modes Transient Operation Constant Power CW ModeContinuous List Operation Trigger ModePulse Input Control Triggered OperationShort On/Off Input On/Off Protection FeaturesOperation Range Over Voltage Over Temperature Over PowerPin trigger and remote sensing connectors Remote Sense Function and Trigger Function Wiring diagram for remote sense Saving and Recalling Settings Operation Battery Testing Action for set Von/Voff value Von/Voff Operation Inspection InstallationLocation Outline Diagram Power CordBench Operation Input Connections Turn-On Checkout Checkout ProcedureIntroduction Trigger and Remote Sensing Connections Case of Trouble Front Panel OperationDisplay Front Panel Display Set set up a constant current from 0 to Max current PowerExample Function keys Set set up a constant resistance from 0.1Ω to 4000Ω Set set up a constant power from 0 to Max powerPOWER=*.***W 000V Set set up a constant voltage from 1.5V to Max voltage Transition Testing OperationOn/Off input setting Shift + Store Continuous Transient Operation Transition Parameter SettingPulse Transient Operation Steps Toggled Transient Operation List Operation Edit the Testing File Automatic Testing Function of Electronic LoadQuick Recall Function Enter Setting the Resolution and number of decimal points Automatic Testing Range Accuracy Resolution Specifications Communication cable Remote Operation ModeIT-E131 RS232 Communication cable IT-E132 USB Communication cable Frame Format Communication between electronic load and PCIT-E132 communication 2AH Communication Protocol Selecting the Remote control mode（20H） Setting / Reading the max input current .（24H/25H） Setting / Reading max input voltage（22H/23H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CV mode voltage value.（2CH/2DH） Setting / Reading CC mode current value（2AH/2BH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting / Reading the number of list steps EH/3FH Setting /Reading the list repeat mode CH/3DH Setting / Reading List file name 48H/49H Save / Get list file in appointed area. CH/4DH Setting / Reading timer value of for Load on 50H/51H） Enable/Disable Local control mode H Setting communication address 54HSelecting / Reading trigger source H/59H Reading input voltage, current, power and relative state FH Sending a trigger signal to trigging the electronic load AH BIT Enter the calibration mode（60H） Calibrate voltage value（62H） Getting the calibration mode state（61H） Calibrate current value（64H） Setting / Reading calibration information（67H/68H）Store the calibration data to EEPROM（66H） For example： Restore the factory default calibration data（69H）Reading information in bar code 6BH Setting information of bar code（6CH） Limited One-Year Warranty Service Information Declaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA