Syntax show sflow | Brocade Communications Systems 6650 instruction

11 sFlow

Brocade#show sflow Flow version: 5

sFlow services are enabled.

sFlow agent IPv6 address: 2001:DB8:2

2 collector destinations configured: Collector IPv6 2001:DB8:1, UDP 6343 Collector IP 10.37.224.233, UDP 6343 Configured UDP source port: 2000 Polling interval is 20 seconds.

Configured default sampling rate: 1 per 100 packets.

Actual default sampling rate: 1 per 100 packets.

The maximum sFlow sample size: 1300. exporting cpu-traffic is enabled. exporting cpu-traffic sample rate: 10. 83715 UDP packets exported

8931 sFlow flow samples collected.

sFlow ports: ethe 1/1/11 ethe 1/1/32 ethe 1/2/1 Module Sampling Rates

---------------------

Port Sampling Rates

-------------------

Port=1/1/11, configured rate=25, actual rate=25 Port=1/1/32, configured rate=10, actual rate=10 Port=1/2/1, configured rate=10, actual rate=10

Syntax: show sflow

The show sflow command displays the following information.

TABLE 56	sFlow information

Parameter		Definition

sFlow version		The version of sFlow enabled on the device, which can be one of the
		following:
		•	2
		•	5

sFlow services		The feature state, which can be one of the following:
		•	disabled
		•	enabled

sFlow agent IP address		The IP address that sFlow is using in the agent_address field of packets
		sent to the collectors. Refer to “sFlow and source address” on page 256.

Collector		The collector information. The following information is displayed for each
		collector:
		•	IP address
		•	UDP port
		If more than one collector is configured, the line above the collectors
		indicates how many have been configured.

Configured UDP source port		The UDP source port used to send data to the collector.

Polling interval		The port counter polling interval.

Configured default sampling rate		The configured global sampling rate. If you changed the global sampling
		rate, the value you entered is shown here. The actual rate calculated by
		the software based on the value you entered is listed on the next line,
		”Actual default sampling rate”.

Actual default sampling rate		The actual default sampling rate.

268	Brocade ICX 6650 Administration Guide
	53-1002600-01

Image 286

Brocade Communications Systems 6650 manual Syntax show sflow, Parameter Definition

Contents

Brocade ICX 6650 Administration Guide Brocade ICX 6650 Administration Guide Title Publication number Summary of changes Date Contents Chapter Operations, Administration, and Maintenance Chapter Ports on Demand Licensing Chapter IPv6 Configuration on Brocade ICX 6650 Switch Full Layer 3 IPv6 feature support Chapter Snmp Access Snmp overview Displaying FDP information FDP configurationFDP Overview Clearing FDP and CDP information Displaying information about installed media Digital optical monitoring configuration limitationsSetting the alarm interval Digital optical monitoring Viewing system information Viewing configuration informationBasic system management Viewing port statistics Local user password changes NIAP-CCEVS certified Brocade equipment Ironware releases Xii Brocade ICX 6650 Administration Guide 53-1002600-01 Supported hardware and software AudienceBrocade ICX 6650 slot and port numbering Document conventions Command syntax conventionsCommand Option, option Argument, arg Arguments Text formatting Show WWN Additional information Related publicationsBrocade resources Document feedback Getting technical helpOther industry resources Brocade ICX 6650 slot and port numbering Management port overview FeatureThis chapter How the management port works Syntax show interfaces management num CLI Commands for use with the management portSyntax show running-config interface management num Syntax show interfaces brief management num Syntax show statistics management num Logging on through the CLISyntax show statistics brief management num Online help Command completionScroll control Line editing commands Using slot number, and port number with CLI commandsCtrl+Key combination Description CLI nomenclature on Brocade ICX 6650 models Searching and filtering output from CLI commandsSearching and filtering output from Show commands Displaying lines containing a specified string Displaying lines starting with a specified string Searching and filtering output at the --More-- promptResults of the search are displayed Filtered results are displayed Using special characters in regular expressionsCharacter Operation Character Operation Syntax unalias alias-name Creating an alias for a CLI commandConfiguration notes for creating a command alias Syntax alias Brocade ICX 6650 Administration Guide 53-1002600-01 Using slot number, and port number with CLI commands Basic System Parameters Basic Port Parameters Basic system parameter configuration Basic system parameter configuration Entering system administration informationSnmp parameter configuration Specifying an Snmp trap receiver Specifying a single trap source Syntax snmp-server host ip-addr0 1 string port value Disabling Snmp traps Setting the Snmp trap holddown timeSyntax no snmp-server enable traps holddown-time secs Snmp Layer 2 traps Syntax no enable snmp ve-statistics Disabling Syslog messages and traps for CLI accessSyntax no snmp-server enable traps trap-type Displaying virtual routing interface statistics Syntax show logging Examples of Syslog messages for CLI accessDisabling the Syslog messages and traps Syntax no logging enable user-login Cancelling an outbound Telnet sessionSpecifying an Sntp server Syntax show sntp associations Syntax no sntp poll-intervalField Description Output from the show sntp associations details command Syntax show sntp associations details Configuring the device as an Sntp server Configuring the device as an Sntp serverSyntax show sntp status Sntp server-mode authentication-key 2 $QHMiR3NzQA= Displaying Sntp server information Enabling broadcast mode for an Sntp clientOutput from the show sntp server-modecommand Syntax show sntp server-mode Setting the system clock Syntax sntp broadcast client Syntax sntp sync System time for daylight saving time. commandNew start and end dates for US daylight saving time Syntax no clock summer-time Limiting broadcast, multicast, and unknown unicast traffic CLI banner configurationSetting a message of the day banner Syntax no clock timezone us timezone-type Use the no form of the command to disable the requirement Syntax no banner motd require-enter-key Syntax no banner execmode delimiting-character Setting a privileged Exec CLI level bannerLocal MAC address for Layer 2 management traffic Syntax no banner incoming delimiting-character Syntax no use-local-management-mac Basic port parameter configurationAssigning a port name Syntax port-name text Basic port parameter configuration Port speed and duplex mode modificationPort speed and duplex mode configuration syntax Syntax speed-duplex value Syntax no speed-duplex 10g-full 1000-full-master Value can be one of the following Full Half Auto default Modifying port duplex modePort duplex mode configuration syntax Maximum port speed application notes Disabling or re-enabling a port Flow control configurationFlow control configuration notes Disabling or re-enabling flow control Syntax no flow-control Negotiation and advertisement of flow controlSyntax no flow-control neg-on Symmetric flow control on Brocade ICX 6650 devices Displaying flow-control status 1G or 10G ports About XON and Xoff thresholds40G ports IPG configuration notes Interpacket Gap IPG on a Brocade ICX 6650 switchChanging the Gbps fiber negotiation mode Enabling and disabling symmetric flow control Syntax gig-default neg-full-auto auto-gig neg-off Port flap dampening configurationPort flap dampening configuration notes Port priority QoS modification Re-enabling a port disabled by port flap dampening Configuring port flap dampening on an interfaceConfiguring port flap dampening on a trunk Displaying ports configured with port flap dampening Syslog messages for port flap dampening Syntax show link-error-disable allColumn Description Port loop detection Recovering disabled portsPort loopback detection configuration notes Types of loop detection Enabling loop detection Configuring a global loop detection intervalConfiguring the device to automatically re-enable ports Syntax no loop-detection Syntax no errdisable recovery interval seconds Specifying the recovery time intervalSyntax no errdisable recovery cause loop-detection Clearing loop-detection Syntax show loop-detection resource Displaying loop detection resource informationFieldDescription Syslog message due to disabled port in loop detection Loop Detection is Enabled Basic port parameter configuration Operations, Administration, and Maintenance Feature Brocade ICX 6650 Determining the flash image version running on the device Software versions installed and running on a deviceOAM Overview Brocade ICX 6650 devices Software versions installed and running on a device Displaying the boot image version running on the deviceDisplaying the image versions installed in flash memory Boot code version is shown in bold type Use the following command syntax to verify the flash image Flash image CLI commandsFlash image verification Viewing the contents of flash files Software upgradesImage file types Syntax show dir Using Snmp to upgrade softwareUsing Snmp to upgrade software Syntax copy flash console filename Snmp-server community string ro rw Software boot configuration notes Software rebootDisplaying the boot preference Software reboot Loading and saving configuration files Loading and saving configuration filesSyntax show boot-preference Logging changes to the startup-config file Syntax no logging enable config-changed Dynamic configuration usage considerations Copying a configuration file to or from a Tftp serverDynamic configuration loading Preparing the configuration file CLI responds like this Following command line will not initiate batch mode Copying a file from the running or startup configuration Loading and saving configuration files with IPv6Using the IPv6 copy command Copying a file to an IPv6 Tftp server Copying a file from an IPv6 Tftp server Copying a file to the running or startup configurationLoading and saving configuration files with IPv6 Copying a file to flash memory IPv6 ncopy command IPv6 Tftp server file upload Using Snmp to save and load configuration information Reloading at a specific time Erasing image and configuration filesSystem reload scheduling Syntax reload at hhmmss mm-dd-yyprimary secondary Error Message Explanation and action Code Diagnostic error codes and remedies for Tftp transfersCanceling a scheduled reload Reloading after a specific amount of time Network connectivity testing Network connectivity testingPinging an IPv4 address Network connectivity testing Tracing an IPv4 route Network connectivity testing Feature Brocade ICX Ports on Demand Overview PoD licensing rules PoD licensing configuration tasksPorts on Demand terminology Ports on Demand terminology Configuration task Reference Obtaining a PoD license Shows the Software Portal Login window Brocade Software Portal Login window License Management Welcome window PoD licensing configuration tasks Brocade ICX 6650 Administration Guide 53-1002600-01 LID Shows an example of the license query results Ports on Demand Licensing Transferring a PoD licenseSyslog message information Front panel PoD PoD licenses Rear panel Flexible Ports on DemandPorts on Demand Licensing Trial licenses are not available for PoD licensing Enabling ports on the front panelPorts on Demand Licensing PoD licenses License SKU License Name Function Example, the license is copied to unit Syntax scp licensefileonhost user@IPaddresslicenseunit id Deleting a ICX6650-10G-LIC-POD license Example above, the license is copied to unit Syntax show pod Enabling ports on the rear panelIPaddress variable is the address of the IPv4 Tftp server Syntax no fpod-40g-enable group groupID Enable ports in group Enter the following command to disable the ports in groupEnable ports for group Disabling the FPoD ports on the rear panel Deleting a 10 GbE or 40 GbE license Viewing information about PoD licenses Syntax license delete unit unitid all index licenseindex Viewing information about PoD licenses Displaying general license information for PoD portsSyntax show license Syntax show license unit unitid Syntax show license unit unitid index indexnumber Field Description Lic-Used Field Description 40GigabitEthernet1/2/1 is up, line protocol is up Viewing information about PoD licenses IPv6 Configuration on Brocade ICX 6650 Switch IPv6 copy Using the IPv6 copy command on Full Layer 3 IPv6 feature support IPv6 addressing overview IPv6 address types IPv6 addressing overview IPv6 address types Address Description Address structure Type IPv6 stateless auto-configuration IPv6 CLI command supportIPv6 command Description Switch code Router code Description Switch code Router code IPv6 host address on a Layer 2 switch Syntax no ipv6 enable Syntax ipv6 address ipv6-addresslink-local Enabling IPv6 routing Configuring basic IPv6 connectivity on a Layer 3 switchIPv6 configuration on each router interface Syntax no ipv6 unicast-routing Ospf Configuring a link-local IPv6 address on an interface Configuring basic IPv6 connectivity on a Layer 3 switch Configuring an IPv6 anycast address on an interface Configuring IPv4 and IPv6 protocol stacksSyntax ip address ip-addresssub-net-masksecondary Configuring IPv6 management ACLs Syntax no ipv6 access-list ACL name Configuring Sntp over IPv6 Restricting Snmp access to an IPv6 nodeConfiguring Snmp V3 over IPv6 Specifying an IPv6 Snmp trap receiver IPv6 traceroute IPv6 TelnetEstablishing a Telnet session from an IPv6 host Syntax traceroute ipv6 ipv6-address Defining an IPv6 DNS entrySyntax no ipv6 dns domain-name domain name Pinging an IPv6 address Configuring an IPv6 Syslog server Viewing IPv6 Snmp server addresses Disabling IPv6 on a Layer 2 switch Static IPv6 route configurationDisabling router advertisement and solicitation messages Configuring a static IPv6 route Dest-ipv6-prefix parameter Parameter Configuration details StatusPrefix-length parameter IPv6 over IPv4 tunnels IPv6 over IPv4 tunnel configuration notesConfiguring a manual IPv6 tunnel IPv6 over IPv4 tunnels Clearing IPv6 tunnel statistics Displaying tunnel interface information Displaying IPv6 tunnel informationDisplaying a summary of tunnel information Syntax clear ipv6 tunnel number Displaying interface level IPv6 settings Syntax show interfaces tunnel number Display command above reflects the following configuration Ecmp load sharing for IPv6 Ecmp load sharing for IPv6 Changing the maximum load sharing paths for IPv6 Disabling or re-enabling Ecmp load sharing for IPv6Displaying Ecmp load-sharing information for IPv6 IPv6 Icmp feature configuration IPv6 Icmp feature configurationConfiguring Icmp rate limiting Syntax ipv6 icmp error-interval interval number-of-tokens Enabling IPv6 Icmp redirect messages IPv6 neighbor discovery configurationIPv6 neighbor discovery configuration Syntax no ipv6 redirects Neighbor solicitation and advertisement messages IPv6 neighbor discovery configuration notesNeighbor discovery is not supported on tunnel interfaces Router advertisement and solicitation messages Neighbor redirect messages Setting IPv6 router advertisement parameters Here is another example with a specified range Prefixes advertised in IPv6 router advertisement messages Enabling and disabling IPv6 router advertisements Setting flags in IPv6 router advertisement messagesSyntax no ipv6 nd suppress-ra IPv6 MTU Configuring reachable time for remote IPv6 nodesConfiguration notes and feature limitations for IPv6 MTU IPv6 MTU Changing the IPv6 MTU Static neighbor entries configurationSyntax no ipv6 mtu bytes Clearing global IPv6 information Limiting the number of hops an IPv6 packet can traverseIPv6 source routing security enhancements Syntax no ipv6 hop-limit number Clearing IPv6 neighbor information Clearing the IPv6 cacheClearing global IPv6 information Clearing IPv6 traffic statistics Displaying global IPv6 informationClearing IPv6 routes from the IPv6 route table Displaying IPv6 cache information Displaying IPv6 interface information 142 Brocade ICX 6650 Administration Guide 53-1002600-01 Icmp Displaying IPv6 neighbor information Displaying the IPv6 route table Displaying local IPv6 routers Syntax show ipv6 router Displaying IPv6 TCP informationPort Syntax show ipv6 tcp connections Free TCP = percentage General IPv6 TCP connection fields = percentage Location of the TCP Syntax show ipv6 traffic Displaying IPv6 traffic statisticsField Description IPv6 statistics ICMP6 statistics Applies to received only TCP statistics Snmp Access Snmp overview Adding an Snmp community string Snmp community stringsEncryption of Snmp community strings Snmp community strings Snmp-server community 1 encrypted-string rw Displaying the Snmp community strings Syntax show snmp server User-based security model Configuring your NMSConfiguring Snmp version 3 on Brocade ICX 6650 devices Defining the engine id Defining an Snmp group Snmp version 3. If you want commandSyntax no snmp-server engineid local hex-string Defining an Snmp user account 162 Brocade ICX 6650 Administration Guide 53-1002600-01 Syntax system-max view number-of-views Defining Snmp viewsSyntax no snmp-server view name mibtree included excluded Snmp version 3 traps To delete a view, use the no parameter before the commandSnmp version 3 traps Defining the UDP port for Snmp v3 traps Trap MIB changes Snmp v3 over IPv6 Restricting Snmp Access to an IPv6 NodeSpecifying an IPv6 host as an Snmp trap receiver Backward compatibility with SMIv1 trap format Displaying Snmp Information Displaying Snmp InformationDisplaying the Engine ID Syntax show snmp engineid Interpreting varbinds in report packets Displaying Snmp groupsDisplaying user information Syntax show snmp group More detailed Snmp v3 configuration Snmp v3 configuration examplesSimple Snmp v3 configuration Snmp v3 configuration examples 170 Brocade ICX 6650 Administration Guide 53-1002600-01 FDP Overview FDP Overview CDP packets Enabling FDP globally FDP configurationChanging the FDP update timer Enabling FDP at the interface level Changing the FDP hold time Syntax no fdp timer secsDisplaying FDP information Displaying neighbor information This line Displays Entry addresses Brocade ICX 6650 Administration Guide 175 53-1002600-01 Displaying FDP and CDP statistics Clearing FDP and CDP informationDisplaying FDP information for an interface Clearing FDP and CDP neighbor information Enabling interception of CDP packets on an interface CDP packetsEnabling interception of CDP packets globally Clearing FDP and CDP statistics Displaying CDP information Displaying neighbors Displaying CDP entries Syntax show fdp entry * device-id Clearing CDP information To clear CDP statistics, enter the following commandDisplaying CDP statistics Lldp and LLDP-MED Lldp terms used in this chapter Supported Lldp features Lldp terms used in this chapter Lldp overview Illustrates Lldp connectivity Benefits of Lldp LLDP-MED overviewLLDP-MED overview Benefits of LLDP-MED LLDP-MED connectivity LLDP-MED class Lldp transmit modeGeneral Lldp operating principles Lldp operating modes Lldp receive mode Lldp packets Lldp TLVs TLV supportOrganizationally-specific TLVs Chassis ID LLDP-MED TLVsMandatory TLVs Chassis ID TLV is always the first TLV in the Lldpdu Port ID TLV packet format TTL value Syslog messages MIB supportMIB support TTL TLV format is shown below Lldp configuration Lldp configurationLldp configuration notes and considerations Global task Default behavior / value when Lldp is enabled Enabling and disabling Lldp Changing a port Lldp operating modeEnabling support for tagged Lldp packets Enabling and disabling receive only mode Enabling and Disabling Transmit Only Mode Specifying the maximum number Lldp neighbors per device Maximum number of Lldp neighborsSyntax no lldp max-total-neighbors value Specifying the maximum number Lldp neighbors per port Enabling Lldp Snmp notifications and Syslog messagesSyntax no lldp max-neighbors-per-port value Changing the minimum time between Lldp transmissions Syntax no lldp transmit-delay secondsSyntax no lldp snmp-notification-interval seconds Syntax no lldp transmit-interval seconds Changing the interval between regular Lldp transmissionsChanging the holdtime multiplier for transmit TTL Syntax no lldp transmit-hold value Lldp TLVs advertised by the Brocade device Syntax no lldp reinit-delay secondsChanging the minimum time between port reinitializations General system information for Lldp Management Address Port description System capabilities System description System name CapabilitiesVlan name Untagged Vlan ID Link aggregation TLV MAC and PHY configuration status This section provides the details for configuring LLDP-MED LLDP-MED configurationLLDP-MED configuration Maximum frame size Default behavior / value Changing the fast start repeat count Syntax no lldp med fast-start-repeat-count value Defining a location id Coordinate-based location Example coordinate-based location configuration Example coordinate-based location advertisement Configuring civic address location Type value elem CA type value elem CA type value LLDP-MED configuration Elements used with civic address Description Acceptable values / examples Type Example civic address location advertisement Configuring emergency call serviceNumber variable is a number from 10 to 25 digits in length Defining an LLDP-MED network policy LLDP-MED network policy configuration syntaxExample ECS Elin location advertisements 216 Brocade ICX 6650 Administration Guide 53-1002600-01 LLDP-MED attributes advertised by the Brocade device LLDP-MED capabilities Lldp configuration summary Displaying Lldp statistics and configuration settingsLLDP-MED attributes advertised by the Brocade device Displaying Lldp statistics Syntax show lldp Clear lldp statistics all command was issued Syntax show lldp statistics Displaying Lldp neighbors Syntax show lldp neighbors Displaying Lldp configuration details Displaying Lldp neighbors detail Resetting Lldp statistics Clearing cached Lldp neighbor information Enabling digital optical monitoring Digital optical monitoring configuration limitationsDigital optical monitoring Syntax no optical-monitor Displaying information about installed media Setting the alarm intervalSyntax no optical-monitor alarm-interval Empty Viewing optical monitoring information Syntax show media slot slot ethernet stack-unit/slot/port Viewing optical transceiver thresholds Status value Description Syslog messages for optical transceivers Syntax show optic threshold stack-unit/slot/port Syslog About Syslog messages Displaying Syslog messages Syntax no logging console Enabling real-time display of Syslog messagesEnabling real-time display for a Telnet or SSH session Syntax terminal monitor Syslog service configuration Syslog service configurationDisplaying the Syslog configuration Displaying real-time Syslog messages Static and dynamic buffers Field Definition Time stamps Clearing log entriesSyntax clear logging dynamic-buffer static-buffer Brocade ICX 6650 Administration Guide 237 53-1002600-01 Specifying a Syslog server To specify a Syslog server, enter the logging host commandDisabling or re-enabling Syslog Syntax no logging on udp-port Changing the number of entries the local buffer can hold Specifying an additional Syslog serverDisabling logging of a message level Syntax no logging buffered level num-entries Changing the log facility Local buffer configuration notesSyntax logging facility facility-name Displaying TCP or UDP port numbers in Syslog messages Displaying interface names in Syslog messagesSyntax no Ip show-portname Syslog reboot configuration considerations Retaining Syslog messages after a soft rebootClearing the Syslog messages from the local buffer Basic system management Viewing system information Viewing configuration information Syntax show version Syntax show statistics ethernet stack-unit/slot/port Viewing port statisticsSyntax show option Port statistics Parameter Description Basic system management Port statisticsStatistics Viewing STP statistics Clearing statistics Syntax clear option Viewing egress queue counters Syntax show interface ethernet stack-unit/slot/port Clearing the egress queue counters Rmon supportMaximum number of entries allowed Rmon control table Syntax clear statistics ethernet stack-unit/slot/port Syntax show rmon statistics ethernet stack-unit/slot/port Statistics Rmon groupRmon support ParameterDefinition Rmon support Export configuration and statistics Parameter Definition History Rmon group Alarm Rmon groupEvent Rmon group SFlow SFlow version Extended router information SFlow support for IPv6 packetsExtended gateway information SFlow and hardware support SFlow configuration considerationsIPv6 packet sampling SFlow and CPU utilization SFlow and source port Configuring and enabling sFlowSFlow and sampling rate Specifying an sFlow collector on IPv4 devices Specifying the collectorSyntax no sflow destination ip-addrdest-udp-port Specifying an sFlow collector on IPv6 devices Changing the polling intervalChanging the sampling rate Syntax no sflow destination ipv6 ip-addrdest-udp-port Change to global rate Configuration considerationsConfigured rate and actual rate Module rate Changing the sampling rate of a module Changing the default sampling rateSyntax no sflow sample num Changing the sampling rate on a port Changing the sampling rate for a trunk port Changing the sFlow source port Command syntax for enabling sFlow forwardingEnabling sFlow forwarding Syntax no sflow source-port num SFlow version 5 feature configuration Syntax no sflow enable Syntax no sflow forwarding Specifying the version used for exporting sFlow data Specifying the sFlow version formatSpecifying the sFlow agent IP address Syntax no sflow agent-ip ipv4-addr Syntax no sflow max-packet-size size Specifying the maximum flow sample sizeSyntax no sflow version 2 Syntax no sflow export system-info Syntax no sflow export cpu-traffic Displaying sFlow informationEnabling the sFlow agent to export CPU-directed data Specifying the sampling rate for exported CPU-directed data Syntax show sflow SFlow SFlow information Clearing sFlow statisticsSyntax clear statistics Utilization list for an uplink port Utilization list for an uplink port command syntaxUtilization list for an uplink port Displaying utilization percentages for an uplink Syntax show relative-utilization num 272 Brocade ICX 6650 Administration Guide 53-1002600-01 Fan num, location , failed Brocade Syslog messagesMessage Explanation Mac-address on portnum Syslog messages Brocade Syslog messages PCI-device-number, Reg Offset PCI-config-register-offsetPCI-bus-number, Dev Addr memory-address From session-id Message level ExplanationLevel shutdown-degrees C degrees Username from session-id filter User username from session-id Root ID root-id Stp-state Vlan-id MAC address any MAC address any, dst mac = DestinationIP=ipaddr Port-number Fan speed Unit/slot/port on vlan-id Unit/slot/port toUnit/slot/port on VLANs vlan-id to Vlan-id Unit/slot/port on Vlan vlan-id Vlan vlan-id interface portnum STP Mac-address MgmtPriChgMac-address MsgAgeExpiry Mac-address RootPort portnum Portnum DOT1X Port portid Mac macaddress Rid router-id, intf addr ip-addr Macaddress on port portidState ospf-state 286 Brocade ICX 6650 Administration Guide 53-1002600-01 Pkt type pkt-type Ip-addr, pkt type type Type Rid router-id, limit num LSA id lsa-id, LSA rid lsa-router-idArea area-id, LSA type lsa-type Ospf-state Brocade ICX 6650 Administration Guide 291 53-1002600-01 Interface configuration error has occurred Rid router-id, area area-id Nbr ip-addr, state ospf-state Rid router-id, nbr addr ip-addr Mac-address State vrrp-stateMac-addr interface portnum Eportnum, address mac-address List ACL-num denied ip-protoEthernet portnum mac-addr Portnum src macaddr mac-addr Chassis temperature has risen above the warning level 298 Brocade ICX 6650 Administration Guide 53-1002600-01 NIAP-CCEVS certified Brocade equipment Ironware releases Local user password changesBrocade product Brocade IronWare Discussed Software version 300 Brocade ICX 6650 Administration Guide 53-1002600-01 Index Ipv6 nd prefix-advertisement,134 Lldp advertise mac-phy-config-status portsLldp enable receive ports Clear fdp table, 176 Brocade ICX 6650 Administration Guide 303 53-1002600-01 FDP Icmp 131 LLDP-MED 266 Snmp SSH XON and Xoff thresholds 312 Brocade ICX 6650 Administration Guide 53-1002600-01